[PATCH v4 0/3] spi-nor: Add support for Intel SPI serial flash controller

[Mika Westerberg <mika.westerberg@linux.intel.com>]

This is fourth version of the series. Previous versions can be found:

  v3: https://lwn.net/Articles/697231/
  v2: http://lists.infradead.org/pipermail/linux-mtd/2016-June/068277.html
  v1: https://lkml.org/lkml/2016/6/14/269

This patch series adds support for the Intel SPI serial flash controller
found on many recent Intel CPUs including Baytrail and Braswell. This
driver makes it possible to access the BIOS and other platform data which
is stored on the SPI serial flash. It is also possible to upgrade the BIOS
using this driver if it has not been protected by special hardware bits.

The patch [1/3] includes documentation how to upgrade BIOS on MinnowBoard
MAX.

Since poking the SPI serial flash can brick the machine, this driver can
only be enabled when CONFIG_EXPERT=y and even then it will remain read-only
unless instructed othwerwise by module parameter.

This missed v4.8 and v4.9 so it would be really nice to get it finally
included in v4.10.

Changes from v3:

[1/3] spi-nor: Add support for Intel SPI serial flash controller
  
  * No changes

[2/3] mfd: lpc_ich: Add support for SPI serial flash host controller

  * Added ACK from Lee Jones.

[3/3] mfd: lpc_ich: Add support for Intel Apollo Lake SoC
   
  * Use bus instead of dev->bus in PCI accesses
  * Added ACK from Lee Jones.

Changes from v2:

  * Rebased on top of v4.8-rc2

  * Updated intel_spi_read/write() according spi-nor core changes which
    drops retlen parameter and returns number of bytes read/written.

Changes from v1:

[1/3] spi-nor: Add support for Intel SPI serial flash controller

  * Older hardware does not support 64k erase command so added erase_64k
    flag which is set only for Broxton (BXT).

  * Fix protection range offset for Broxton. Now there is ispi->pregs
    pointing to the start of the protection registers.

  * Change naming of constants from BCR_BYT -> BYT_BCR and so on.

[2/3] mfd: lpc_ich: Add support for SPI serial flash host controller

  * Drop lpc_ich_finalize_spi_cell() and initialize cell directly in
    lpc_ich_init_spi().

  * Use info->type in switch in lpc_ich_init_spi().

  * Add defines for magic numbers used in lpc_ich_init_spi().

  * Use PLATFORM_DEVID_NONE with mfd_add_devices().

[3/3] mfd: lpc_ich: Add support for Intel Apollo Lake SoC

  * No changes

Mika Westerberg (3):
  spi-nor: Add support for Intel SPI serial flash controller
  mfd: lpc_ich: Add support for SPI serial flash host controller
  mfd: lpc_ich: Add support for Intel Apollo Lake SoC

 Documentation/mtd/intel-spi.txt          |  88 ++++
 drivers/mfd/lpc_ich.c                    | 131 ++++++
 drivers/mtd/spi-nor/Kconfig              |  20 +
 drivers/mtd/spi-nor/Makefile             |   2 +
 drivers/mtd/spi-nor/intel-spi-platform.c |  57 +++
 drivers/mtd/spi-nor/intel-spi.c          | 780 +++++++++++++++++++++++++++++++
 drivers/mtd/spi-nor/intel-spi.h          |  24 +
 include/linux/mfd/lpc_ich.h              |   3 +
 include/linux/platform_data/intel-spi.h  |  31 ++
 9 files changed, 1136 insertions(+)
 create mode 100644 Documentation/mtd/intel-spi.txt
 create mode 100644 drivers/mtd/spi-nor/intel-spi-platform.c
 create mode 100644 drivers/mtd/spi-nor/intel-spi.c
 create mode 100644 drivers/mtd/spi-nor/intel-spi.h
 create mode 100644 include/linux/platform_data/intel-spi.h

-- 
2.9.3