From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1755457AbdEMOgg (ORCPT ); Sat, 13 May 2017 10:36:36 -0400 Received: from mx2.suse.de ([195.135.220.15]:37215 "EHLO mx1.suse.de" rhost-flags-OK-OK-OK-FAIL) by vger.kernel.org with ESMTP id S1754422AbdEMOdv (ORCPT ); Sat, 13 May 2017 10:33:51 -0400 From: =?UTF-8?q?Andreas=20F=C3=A4rber?= To: linux-amlogic@lists.infradead.org Cc: Carlo Caione , Kevin Hilman , linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, =?UTF-8?q?Andreas=20F=C3=A4rber?= , Rob Herring , Mark Rutland , Catalin Marinas , Will Deacon , devicetree@vger.kernel.org Subject: [PATCH v2 11/18] arm64: dts: meson-gxbb-odroidc2: Fix node order Date: Sat, 13 May 2017 16:33:30 +0200 Message-Id: <20170513143337.14278-12-afaerber@suse.de> X-Mailer: git-send-email 2.12.0 In-Reply-To: <20170513143337.14278-1-afaerber@suse.de> References: <20170513143337.14278-1-afaerber@suse.de> MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Sort nodes referenced by label alphabetically. Signed-off-by: Andreas Färber --- v1 -> v2: * Rebased (new nodes added) .../arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts | 108 ++++++++++----------- 1 file changed, 54 insertions(+), 54 deletions(-) diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts index 54a9c6a6b392..d147c853ab05 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts @@ -137,16 +137,6 @@ }; }; -&scpi_clocks { - status = "disabled"; -}; - -&uart_AO { - status = "okay"; - pinctrl-0 = <&uart_ao_a_pins>; - pinctrl-names = "default"; -}; - ðmac { status = "okay"; pinctrl-0 = <ð_rgmii_pins>; @@ -172,6 +162,33 @@ }; }; +&gpio_ao { + /* + * WARNING: The USB Hub on the Odroid-C2 needs a reset signal + * to be turned high in order to be detected by the USB Controller + * This signal should be handled by a USB specific power sequence + * in order to reset the Hub when USB bus is powered down. + */ + usb-hub { + gpio-hog; + gpios = ; + output-high; + line-name = "usb-hub-reset"; + }; +}; + +&i2c_A { + status = "okay"; + pinctrl-0 = <&i2c_a_pins>; + pinctrl-names = "default"; +}; + +&ir { + status = "okay"; + pinctrl-0 = <&remote_input_ao_pins>; + pinctrl-names = "default"; +}; + &pinctrl_aobus { gpio-line-names = "UART TX", "UART RX", "VCCK En", "TF 3V3/1V8 En", "USB HUB nRESET", "USB OTG Power En", @@ -223,55 +240,15 @@ ""; }; -&ir { - status = "okay"; - pinctrl-0 = <&remote_input_ao_pins>; - pinctrl-names = "default"; -}; - -&i2c_A { - status = "okay"; - pinctrl-0 = <&i2c_a_pins>; - pinctrl-names = "default"; -}; - -&gpio_ao { - /* - * WARNING: The USB Hub on the Odroid-C2 needs a reset signal - * to be turned high in order to be detected by the USB Controller - * This signal should be handled by a USB specific power sequence - * in order to reset the Hub when USB bus is powered down. - */ - usb-hub { - gpio-hog; - gpios = ; - output-high; - line-name = "usb-hub-reset"; - }; -}; - -&usb0_phy { - status = "okay"; - phy-supply = <&usb_otg_pwr>; -}; - -&usb1_phy { - status = "okay"; -}; - -&usb0 { - status = "okay"; -}; - -&usb1 { - status = "okay"; -}; - &saradc { status = "okay"; vref-supply = <&vcc1v8>; }; +&scpi_clocks { + status = "disabled"; +}; + /* SD */ &sd_emmc_b { status = "okay"; @@ -309,3 +286,26 @@ vmmc-supply = <&vcc3v3>; vqmmc-supply = <&vcc1v8>; }; + +&uart_AO { + status = "okay"; + pinctrl-0 = <&uart_ao_a_pins>; + pinctrl-names = "default"; +}; + +&usb0_phy { + status = "okay"; + phy-supply = <&usb_otg_pwr>; +}; + +&usb1_phy { + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; + +&usb1 { + status = "okay"; +}; -- 2.12.0