Re: [PATCH v1] clocksource/timer-atmel-pit:- Fix resource leaks in error paths.

[Alexandre Belloni <alexandre.belloni@free-electrons.com>]

On 18/05/2017 at 16:03:48 +0530, Arvind Yadav wrote:
> Hi,
> Yes i have tested on board SBC6045 with Atmel SoC.
> 

Ok, thanks.

> Commit message  " Handle return error in at91sam926x_pit_dt_init.
> at91sam926x_pit_dt_init can fail here. We must have released memory
> and clock "
> 
> is this fine?
> 

Sure.

My point is that currently, if any of it fails, your board will not boot
anyway ;).

> Regards
> -Arvind
> 
> On Thursday 18 May 2017 02:56 PM, Alexandre Belloni wrote:
> > Hi,
> > 
> > This needs a proper commit message. Also, can you tell us on which SoC
> > you tested your changes?
> > 
> > On 05/05/2017 at 18:21:48 +0530, Arvind Yadav wrote:
> > > Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
> > > ---
> > >   drivers/clocksource/timer-atmel-pit.c | 30 +++++++++++++++++++++++-------
> > >   1 file changed, 23 insertions(+), 7 deletions(-)
> > > 
> > > diff --git a/drivers/clocksource/timer-atmel-pit.c b/drivers/clocksource/timer-atmel-pit.c
> > > index c0b5df3..28b0cd3 100644
> > > --- a/drivers/clocksource/timer-atmel-pit.c
> > > +++ b/drivers/clocksource/timer-atmel-pit.c
> > > @@ -180,26 +180,29 @@ static int __init at91sam926x_pit_dt_init(struct device_node *node)
> > >   	data->base = of_iomap(node, 0);
> > >   	if (!data->base) {
> > >   		pr_err("Could not map PIT address\n");
> > > -		return -ENXIO;
> > > +		ret = -ENXIO;
> > > +		goto error_free;
> > >   	}
> > >   	data->mck = of_clk_get(node, 0);
> > >   	if (IS_ERR(data->mck)) {
> > >   		pr_err("Unable to get mck clk\n");
> > > -		return PTR_ERR(data->mck);
> > > +		ret = PTR_ERR(data->mck);
> > > +		goto error_iounmap;
> > >   	}
> > >   	ret = clk_prepare_enable(data->mck);
> > >   	if (ret) {
> > >   		pr_err("Unable to enable mck\n");
> > > -		return ret;
> > > +		goto error_clk_put;
> > >   	}
> > >   	/* Get the interrupts property */
> > >   	data->irq = irq_of_parse_and_map(node, 0);
> > >   	if (!data->irq) {
> > >   		pr_err("Unable to get IRQ from DT\n");
> > > -		return -EINVAL;
> > > +		ret = -EINVAL;
> > > +		goto error_clk_disable;
> > >   	}
> > >   	/*
> > > @@ -223,11 +226,11 @@ static int __init at91sam926x_pit_dt_init(struct device_node *node)
> > >   	data->clksrc.rating = 175;
> > >   	data->clksrc.read = read_pit_clk;
> > >   	data->clksrc.flags = CLOCK_SOURCE_IS_CONTINUOUS;
> > > -	
> > > +
> > >   	ret = clocksource_register_hz(&data->clksrc, pit_rate);
> > >   	if (ret) {
> > >   		pr_err("Failed to register clocksource");
> > > -		return ret;
> > > +		goto error_clk_disable;
> > >   	}
> > >   	/* Set up irq handler */
> > > @@ -236,7 +239,7 @@ static int __init at91sam926x_pit_dt_init(struct device_node *node)
> > >   			  "at91_tick", data);
> > >   	if (ret) {
> > >   		pr_err("Unable to setup IRQ\n");
> > > -		return ret;
> > > +		goto error_unregister_clk;
> > >   	}
> > >   	/* Set up and register clockevents */
> > > @@ -254,6 +257,19 @@ static int __init at91sam926x_pit_dt_init(struct device_node *node)
> > >   	clockevents_register_device(&data->clkevt);
> > >   	return 0;
> > > +
> > > +error_unregister_clk:
> > > +	clocksource_unregister(&data->clksrc);
> > > +error_clk_disable:
> > > +	clk_disable_unprepare(data->mck);
> > > +error_clk_put:
> > > +	clk_put(data->mck);
> > > +error_iounmap:
> > > +	iounmap(data->base);
> > > +error_free:
> > > +	kfree(data);
> > > +
> > > +	return ret;
> > >   }
> > >   CLOCKSOURCE_OF_DECLARE(at91sam926x_pit, "atmel,at91sam9260-pit",
> > >   		       at91sam926x_pit_dt_init);
> > > -- 
> > > 1.9.1
> > > 
> > > 
> 

-- 
Alexandre Belloni, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com