From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1751792AbdFIPew (ORCPT ); Fri, 9 Jun 2017 11:34:52 -0400 Received: from mirror2.csie.ntu.edu.tw ([140.112.30.76]:53914 "EHLO wens.csie.org" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1751543AbdFIPeu (ORCPT ); Fri, 9 Jun 2017 11:34:50 -0400 From: Chen-Yu Tsai To: Maxime Ripard Cc: Chen-Yu Tsai , devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, linux-sunxi@googlegroups.co, Corentin Labbe Subject: [PATCH] ARM: sun8i: h3: Enable EMAC with external PHY on Orange Pi Plus 2E Date: Fri, 9 Jun 2017 23:34:36 +0800 Message-Id: <20170609153436.18370-1-wens@csie.org> X-Mailer: git-send-email 2.11.0 Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org The Orange Pi Plus 2E, unlike the Orange Pi PC and PC Plus which its schematics are based on, uses an external Realtek RTL8211E PHY in RGMII mode, with a GPIO enabling the regulator for I/O signalling power supplies. The PHY's main power supply is enabled by the main 5V power supply. Add the regulator and PHY nodes, and override the PHY phandle under the EMAC node, so that the EMAC works properly on this board. Signed-off-by: Chen-Yu Tsai --- arch/arm/boot/dts/sun8i-h3-orangepi-plus2e.dts | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-plus2e.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-plus2e.dts index 5851a47a3089..80026f3caafc 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-plus2e.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-plus2e.dts @@ -50,4 +50,30 @@ / { model = "Xunlong Orange Pi Plus 2E"; compatible = "xunlong,orangepi-plus2e", "allwinner,sun8i-h3"; + + reg_gmac_3v3: gmac-3v3 { + compatible = "regulator-fixed"; + regulator-name = "gmac-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + startup-delay-us = <100000>; + enable-active-high; + gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */ + }; +}; + +&emac { + pinctrl-names = "default"; + pinctrl-0 = <&emac_rgmii_pins>; + phy-supply = <®_gmac_3v3>; + phy-handle = <&ext_rgmii_phy>; + phy-mode = "rgmii"; + status = "okay"; +}; + +&mdio { + ext_rgmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; }; -- 2.11.0