From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1751783AbdFIQF6 (ORCPT ); Fri, 9 Jun 2017 12:05:58 -0400 Received: from mirror2.csie.ntu.edu.tw ([140.112.30.76]:53940 "EHLO wens.csie.org" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1751562AbdFIQF5 (ORCPT ); Fri, 9 Jun 2017 12:05:57 -0400 From: Chen-Yu Tsai To: Maxime Ripard Cc: Chen-Yu Tsai , devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, linux-sunxi@googlegroups.com Subject: [PATCH] ARM: sun6i: a31s: primo81: Change USB OTG to OTG mode Date: Sat, 10 Jun 2017 00:05:48 +0800 Message-Id: <20170609160549.3566-1-wens@csie.org> X-Mailer: git-send-email 2.11.0 Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Now that we have support for the AXP221 PMIC's USB VBUS detection and DRIVEVBUS vbus control, we can use the USB OTG port in proper OTG mode. This patch enables the aforementioned PMIC functions, adds the OTG ID detection pin to the USB PHY node, and changes the mode of USB OTG to "otg". Signed-off-by: Chen-Yu Tsai --- arch/arm/boot/dts/sun6i-a31s-primo81.dts | 16 ++++++++++++++-- 1 file changed, 14 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/sun6i-a31s-primo81.dts b/arch/arm/boot/dts/sun6i-a31s-primo81.dts index f3712753fa42..73b163a7d9dd 100644 --- a/arch/arm/boot/dts/sun6i-a31s-primo81.dts +++ b/arch/arm/boot/dts/sun6i-a31s-primo81.dts @@ -158,6 +158,7 @@ reg = <0x68>; interrupt-parent = <&nmi_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + x-powers,drive-vbus-en; }; }; @@ -226,6 +227,11 @@ regulator-name = "vddio-csi"; }; +®_drivevbus { + regulator-name = "usb0-vbus"; + status = "okay"; +}; + ®_eldo3 { regulator-min-microvolt = <1080000>; regulator-max-microvolt = <1320000>; @@ -238,12 +244,18 @@ }; &usb_otg { - /* otg support requires support for AXP221 usb-power-supply and GPIO */ - dr_mode = "host"; + dr_mode = "otg"; + status = "okay"; +}; + +&usb_power_supply { status = "okay"; }; &usbphy { + usb0_id_det-gpio = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 */ + usb0_vbus_power-supply = <&usb_power_supply>; + usb0_vbus-supply = <®_drivevbus>; usb1_vbus-supply = <®_dldo1>; status = "okay"; }; -- 2.11.0