From: Rob Herring <robh@kernel.org>
To: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org, "Nishanth Menon" <nm@ti.com>,
devicetree@vger.kernel.org, "Paul Walmsley" <paul@pwsan.com>,
"Dave Gerlach" <d-gerlach@ti.com>,
"Tomi Valkeinen" <tomi.valkeinen@ti.com>,
"Matthijs van Duin" <matthijsvanduin@gmail.com>,
linux-kernel@vger.kernel.org,
"Liam Girdwood" <lgirdwood@gmail.com>,
"Tero Kristo" <t-kristo@ti.com>,
"Mark Brown" <broonie@kernel.org>,
"Sakari Ailus" <sakari.ailus@iki.fi>,
"Laurent Pinchart" <laurent.pinchart@ideasonboard.com>,
"Benoît Cousson" <bcousson@baylibre.com>,
"Mark Rutland" <mark.rutland@arm.com>,
"Mauro Carvalho Chehab" <mchehab@kernel.org>,
linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH 1/9] dt-bindings: ti-sysc: Update binding for timers and capabilities
Date: Sat, 16 Dec 2017 12:31:04 -0600 [thread overview]
Message-ID: <20171216183059.ipsftfnvsyamv6fd@rob-hp-laptop> (raw)
In-Reply-To: <20171215180900.3243-2-tony@atomide.com>
On Fri, Dec 15, 2017 at 10:08:52AM -0800, Tony Lindgren wrote:
> The ti-sysc binding does not yet describe the capabilities of the
> interconnect target module. So to make the ti-sysc binding usable
> for configuring the interconnect target module, we need to add few
> more properties:
>
> 1. To detect between omap2 and omap4 timers, let's add compatibles
> for them for "ti,sysc-omap2-timer" and,sysc-omap4-timer". This
> makes it easier to pick up the already initialized system timers
> later on
>
> 2. Let's add "ti,sysc-mask" for a mask of features supported by the
> interconnect target module. This describes what we have available
> in the various SYSCONFIG registers
>
> 3. Let's add "ti,sysc-midle" and "ti,sysc-sidle" lists for the master
> and slave idle modes supported by the interconnect target module.
> These describe the values available for MIDLE and SIDLE bits in
> the SYSCONFIG registers
>
> 4. Some interconnect target modules need a short delay after reset
> before they can be accessed, let's use "ti,sysc-delay-us" for
> that
>
> 5. Let's add "ti,syss-mask" bit to describe the optional SYSSTATUS
> register bits for reset done bits
>
> 6. Let's support the two existing custom quirk properties already
> listed in Documentation/devicetree/bindings/arm/omap/omap.txt for
> "ti,no-reset-on-init" and "ti,no-idle-on-init"
>
> 7. And finally, let's add a header for the binding for the dts
> files and the driver to use
>
> Cc: Benoît Cousson <bcousson@baylibre.com>
> Cc: Dave Gerlach <d-gerlach@ti.com>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Cc: Liam Girdwood <lgirdwood@gmail.com>
> Cc: Mark Brown <broonie@kernel.org>
> Cc: Mark Rutland <mark.rutland@arm.com>
> Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
> Cc: Nishanth Menon <nm@ti.com>
> Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
> Cc: Paul Walmsley <paul@pwsan.com>
> Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
> Cc: Sakari Ailus <sakari.ailus@iki.fi>
> Cc: Suman Anna <s-anna@ti.com>
> Cc: Tero Kristo <t-kristo@ti.com>
> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
> Signed-off-by: Tony Lindgren <tony@atomide.com>
> ---
> Documentation/devicetree/bindings/bus/ti-sysc.txt | 36 +++++++++++++++++++++++
> include/dt-bindings/bus/ti-sysc.h | 22 ++++++++++++++
> 2 files changed, 58 insertions(+)
> create mode 100644 include/dt-bindings/bus/ti-sysc.h
>
> diff --git a/Documentation/devicetree/bindings/bus/ti-sysc.txt b/Documentation/devicetree/bindings/bus/ti-sysc.txt
> --- a/Documentation/devicetree/bindings/bus/ti-sysc.txt
> +++ b/Documentation/devicetree/bindings/bus/ti-sysc.txt
> @@ -26,6 +26,8 @@ Required standard properties:
> or one of the following derivative types for hardware
> needing special workarounds:
>
> + "ti,sysc-omap2-timer"
> + "ti,sysc-omap4-timer"
> "ti,sysc-omap3430-sr"
> "ti,sysc-omap3630-sr"
> "ti,sysc-omap4-sr"
> @@ -49,6 +51,26 @@ Required standard properties:
>
> Optional properties:
>
> +- ti,sysc-mask shall contain mask of supported register bits for the
> + SYSCONFIG register as documented in the Technical Reference
> + Manual (TRM) for the interconnect target module
> +
> +- ti,sysc-midle list of master idle modes supported by the interconnect
> + target module as documented in the TRM for SYSCONFIG
> + register MIDLEMODE bits
> +
> +- ti,sysc-sidle list of slave idle modes supported by the interconnect
> + target module as documented in the TRM for SYSCONFIG
> + register SIDLEMODE bits
> +
> +- ti,sysc-delay-us delay needed after OCP softreset before accssing
> + SYSCONFIG register again
> +
> +- ti,syss-mask optional mask of reset done status bits as described in the
> + TRM for SYSSTATUS registers, typically 1 with some devices
> + having separate reset done bits for children like OHCI and
> + EHCI
> +
Seems like a lot of this should be implied by specific compatible
strings.
Are the bits you've defined all of them or there's more?
Rob
next prev parent reply other threads:[~2017-12-16 18:31 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-12-15 18:08 [PATCH 0/9] Update ti-sysc driver to use dts for capabilities Tony Lindgren
2017-12-15 18:08 ` [PATCH 1/9] dt-bindings: ti-sysc: Update binding for timers and capabilities Tony Lindgren
2017-12-16 18:31 ` Rob Herring [this message]
2017-12-16 19:22 ` Tony Lindgren
2017-12-20 18:10 ` Rob Herring
2017-12-21 15:29 ` Tony Lindgren
2017-12-15 18:08 ` [PATCH 2/9] ARM: dts: Add generic ti,sysc compatible in addition to the custom ones Tony Lindgren
2017-12-16 18:34 ` [PATCH 2/9] ARM: dts: Add generic ti, sysc " Rob Herring
2017-12-16 19:54 ` Tony Lindgren
2017-12-15 18:08 ` [PATCH 3/9] ARM: OMAP2+: Move all omap_hwmod_sysc_fields to omap_hwmod_common_data.c Tony Lindgren
2017-12-15 18:08 ` [PATCH 4/9] bus: ti-sysc: Make omap_hwmod_sysc_fields into sysc_regbits platform data Tony Lindgren
2017-12-15 18:08 ` [PATCH 5/9] bus: ti-sysc: Add register bits for interconnect target modules Tony Lindgren
2017-12-15 18:08 ` [PATCH 6/9] bus: ti-sysc: Detect i2c interconnect target module based on register layout Tony Lindgren
2017-12-15 18:08 ` [PATCH 7/9] bus: ti-sysc: Handle module quirks based dts configuration Tony Lindgren
2017-12-15 18:08 ` [PATCH 8/9] bus: ti-sysc: Add parsing of module capabilities Tony Lindgren
2017-12-15 18:09 ` [PATCH 9/9] ARM: dts: Update ti-sysc data for existing users Tony Lindgren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20171216183059.ipsftfnvsyamv6fd@rob-hp-laptop \
--to=robh@kernel.org \
--cc=bcousson@baylibre.com \
--cc=broonie@kernel.org \
--cc=d-gerlach@ti.com \
--cc=devicetree@vger.kernel.org \
--cc=laurent.pinchart@ideasonboard.com \
--cc=lgirdwood@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=matthijsvanduin@gmail.com \
--cc=mchehab@kernel.org \
--cc=nm@ti.com \
--cc=paul@pwsan.com \
--cc=sakari.ailus@iki.fi \
--cc=t-kristo@ti.com \
--cc=tomi.valkeinen@ti.com \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®