[PATCH AUTOSEL for 3.18 16/53] [media] media/dvb-core: Race condition when writing to CAM

[Sasha Levin <Alexander.Levin@microsoft.com>]

From: Jasmin J <jasmin@anw.at>

[ Upstream commit e7080d4471d805d921a9ea21b32f911a91e248cb ]

It started with a sporadic message in syslog: "CAM tried to send a
buffer larger than the ecount size" This message is not the fault
itself, but a consecutive fault, after a read error from the CAM. This
happens only on several CAMs, several hardware, and of course sporadic.

It is a consecutive fault, if the last read from the CAM did fail. I
guess this will not happen on all CAMs, but at least it did on mine.
There was a write error to the CAM and during the re-initialization
procedure, the CAM finished the last read, although it got a RS.

The write error to the CAM happened because a race condition between HC
write, checking DA and FR.

This patch added an additional check for DA(RE), just after checking FR.
It is important to read the CAMs status register again, to give the CAM
the necessary time for a proper reaction to HC. Please note the
description within the source code (patch below).

[mchehab@s-opensource.com: make checkpatch happy]

Signed-off-by: Jasmin jessich <jasmin@anw.at>
Tested-by: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/media/dvb-core/dvb_ca_en50221.c | 23 +++++++++++++++++++++++
 1 file changed, 23 insertions(+)

diff --git a/drivers/media/dvb-core/dvb_ca_en50221.c b/drivers/media/dvb-core/dvb_ca_en50221.c
index 0aac3096728e..051bdfac6a1d 100644
--- a/drivers/media/dvb-core/dvb_ca_en50221.c
+++ b/drivers/media/dvb-core/dvb_ca_en50221.c
@@ -749,6 +749,29 @@ static int dvb_ca_en50221_write_data(struct dvb_ca_private *ca, int slot, u8 * b
 		goto exit;
 	}
 
+	/*
+	 * It may need some time for the CAM to settle down, or there might
+	 * be a race condition between the CAM, writing HC and our last
+	 * check for DA. This happens, if the CAM asserts DA, just after
+	 * checking DA before we are setting HC. In this case it might be
+	 * a bug in the CAM to keep the FR bit, the lower layer/HW
+	 * communication requires a longer timeout or the CAM needs more
+	 * time internally. But this happens in reality!
+	 * We need to read the status from the HW again and do the same
+	 * we did for the previous check for DA
+	 */
+	status = ca->pub->read_cam_control(ca->pub, slot, CTRLIF_STATUS);
+	if (status < 0)
+		goto exit;
+
+	if (status & (STATUSREG_DA | STATUSREG_RE)) {
+		if (status & STATUSREG_DA)
+			dvb_ca_en50221_thread_wakeup(ca);
+
+		status = -EAGAIN;
+		goto exit;
+	}
+
 	/* send the amount of data */
 	if ((status = ca->pub->write_cam_control(ca->pub, slot, CTRLIF_SIZE_HIGH, bytes_write >> 8)) != 0)
 		goto exit;
-- 
2.14.1