From: Antoine Tenart <antoine.tenart@bootlin.com>
To: davem@davemloft.net, kishon@ti.com, linux@armlinux.org.uk,
gregory.clement@bootlin.com, andrew@lunn.ch,
jason@lakedaemon.net, sebastian.hesselbarth@gmail.com
Cc: Antoine Tenart <antoine.tenart@bootlin.com>,
netdev@vger.kernel.org, linux-kernel@vger.kernel.org,
thomas.petazzoni@bootlin.com, maxime.chevallier@bootlin.com,
miquel.raynal@bootlin.com, nadavh@marvell.com,
stefanc@marvell.com, ymarkman@marvell.com, mw@semihalf.com,
linux-arm-kernel@lists.infradead.org
Subject: [PATCH net-next 06/10] net: mvpp2: 1000baseX support
Date: Fri, 16 Mar 2018 11:33:47 +0100 [thread overview]
Message-ID: <20180316103351.16616-7-antoine.tenart@bootlin.com> (raw)
In-Reply-To: <20180316103351.16616-1-antoine.tenart@bootlin.com>
This patch adds the 1000Base-X PHY mode support in the Marvell PPv2
driver. 1000Base-X is quite close the SGMII and uses nearly the same
code path.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
---
drivers/net/ethernet/marvell/mvpp2.c | 74 +++++++++++++++++++++++++-----------
1 file changed, 52 insertions(+), 22 deletions(-)
diff --git a/drivers/net/ethernet/marvell/mvpp2.c b/drivers/net/ethernet/marvell/mvpp2.c
index 8e8e7afcd437..f6c35b688af4 100644
--- a/drivers/net/ethernet/marvell/mvpp2.c
+++ b/drivers/net/ethernet/marvell/mvpp2.c
@@ -4896,6 +4896,7 @@ static int mvpp22_gop_init(struct mvpp2_port *port)
mvpp22_gop_init_rgmii(port);
break;
case PHY_INTERFACE_MODE_SGMII:
+ case PHY_INTERFACE_MODE_1000BASEX:
mvpp22_gop_init_sgmii(port);
break;
case PHY_INTERFACE_MODE_10GKR:
@@ -4933,7 +4934,8 @@ static void mvpp22_gop_unmask_irq(struct mvpp2_port *port)
u32 val;
if (phy_interface_mode_is_rgmii(port->phy_interface) ||
- port->phy_interface == PHY_INTERFACE_MODE_SGMII) {
+ port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
/* Enable the GMAC link status irq for this port */
val = readl(port->base + MVPP22_GMAC_INT_SUM_MASK);
val |= MVPP22_GMAC_INT_SUM_MASK_LINK_STAT;
@@ -4963,7 +4965,8 @@ static void mvpp22_gop_mask_irq(struct mvpp2_port *port)
}
if (phy_interface_mode_is_rgmii(port->phy_interface) ||
- port->phy_interface == PHY_INTERFACE_MODE_SGMII) {
+ port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
val = readl(port->base + MVPP22_GMAC_INT_SUM_MASK);
val &= ~MVPP22_GMAC_INT_SUM_MASK_LINK_STAT;
writel(val, port->base + MVPP22_GMAC_INT_SUM_MASK);
@@ -4975,7 +4978,8 @@ static void mvpp22_gop_setup_irq(struct mvpp2_port *port)
u32 val;
if (phy_interface_mode_is_rgmii(port->phy_interface) ||
- port->phy_interface == PHY_INTERFACE_MODE_SGMII) {
+ port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
val = readl(port->base + MVPP22_GMAC_INT_MASK);
val |= MVPP22_GMAC_INT_MASK_LINK_STAT;
writel(val, port->base + MVPP22_GMAC_INT_MASK);
@@ -5000,6 +5004,7 @@ static int mvpp22_comphy_init(struct mvpp2_port *port)
switch (port->phy_interface) {
case PHY_INTERFACE_MODE_SGMII:
+ case PHY_INTERFACE_MODE_1000BASEX:
mode = PHY_MODE_SGMII;
break;
case PHY_INTERFACE_MODE_10GKR:
@@ -5079,7 +5084,8 @@ static void mvpp2_port_loopback_set(struct mvpp2_port *port,
else
val &= ~MVPP2_GMAC_GMII_LB_EN_MASK;
- if (port->phy_interface == PHY_INTERFACE_MODE_SGMII)
+ if (port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX)
val |= MVPP2_GMAC_PCS_LB_EN_MASK;
else
val &= ~MVPP2_GMAC_PCS_LB_EN_MASK;
@@ -6288,7 +6294,8 @@ static irqreturn_t mvpp2_link_status_isr(int irq, void *dev_id)
link = true;
}
} else if (phy_interface_mode_is_rgmii(port->phy_interface) ||
- port->phy_interface == PHY_INTERFACE_MODE_SGMII) {
+ port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
val = readl(port->base + MVPP22_GMAC_INT_STAT);
if (val & MVPP22_GMAC_INT_STAT_LINK) {
event = true;
@@ -8055,21 +8062,25 @@ static void mvpp2_phylink_validate(struct net_device *dev,
phylink_set(mask, Pause);
phylink_set(mask, Asym_Pause);
- phylink_set(mask, 10baseT_Half);
- phylink_set(mask, 10baseT_Full);
- phylink_set(mask, 100baseT_Half);
- phylink_set(mask, 100baseT_Full);
- phylink_set(mask, 1000baseT_Full);
- phylink_set(mask, 1000baseX_Full);
- phylink_set(mask, 10000baseT_Full);
-
- if (state->interface == PHY_INTERFACE_MODE_10GKR) {
+ switch (state->interface) {
+ case PHY_INTERFACE_MODE_10GKR:
phylink_set(mask, 10000baseCR_Full);
phylink_set(mask, 10000baseSR_Full);
phylink_set(mask, 10000baseLR_Full);
phylink_set(mask, 10000baseLRM_Full);
phylink_set(mask, 10000baseER_Full);
phylink_set(mask, 10000baseKR_Full);
+ /* Fall-through */
+ default:
+ phylink_set(mask, 10baseT_Half);
+ phylink_set(mask, 10baseT_Full);
+ phylink_set(mask, 100baseT_Half);
+ phylink_set(mask, 100baseT_Full);
+ phylink_set(mask, 10000baseT_Full);
+ /* Fall-through */
+ case PHY_INTERFACE_MODE_1000BASEX:
+ phylink_set(mask, 1000baseT_Full);
+ phylink_set(mask, 1000baseX_Full);
}
bitmap_and(supported, supported, mask, __ETHTOOL_LINK_MODE_MASK_NBITS);
@@ -8108,12 +8119,18 @@ static void mvpp2_gmac_link_state(struct mvpp2_port *port,
state->link = !!(val & MVPP2_GMAC_STATUS0_LINK_UP);
state->duplex = !!(val & MVPP2_GMAC_STATUS0_FULL_DUPLEX);
- if (val & MVPP2_GMAC_STATUS0_GMII_SPEED)
+ switch (port->phy_interface) {
+ case PHY_INTERFACE_MODE_1000BASEX:
state->speed = SPEED_1000;
- else if (val & MVPP2_GMAC_STATUS0_MII_SPEED)
- state->speed = SPEED_100;
- else
- state->speed = SPEED_10;
+ break;
+ default:
+ if (val & MVPP2_GMAC_STATUS0_GMII_SPEED)
+ state->speed = SPEED_1000;
+ else if (val & MVPP2_GMAC_STATUS0_MII_SPEED)
+ state->speed = SPEED_100;
+ else
+ state->speed = SPEED_10;
+ }
state->pause = 0;
if (val & MVPP2_GMAC_STATUS0_RX_PAUSE)
@@ -8204,7 +8221,18 @@ static void mvpp2_gmac_config(struct mvpp2_port *port, unsigned int mode,
ctrl0 &= ~MVPP2_GMAC_PORT_TYPE_MASK;
ctrl2 &= ~(MVPP2_GMAC_PORT_RESET_MASK | MVPP2_GMAC_PCS_ENABLE_MASK);
- an |= MVPP2_GMAC_AN_SPEED_EN | MVPP2_GMAC_FLOW_CTRL_AUTONEG;
+ if (state->interface == PHY_INTERFACE_MODE_1000BASEX) {
+ /* 1000BaseX port cannot negotiate speed nor can it negotiate
+ * duplex: they are always operating with a fixed speed of
+ * 1000Mbps in full duplex, so force 1000 speed and full duplex
+ * here.
+ */
+ ctrl0 |= MVPP2_GMAC_PORT_TYPE_MASK;
+ an |= MVPP2_GMAC_CONFIG_GMII_SPEED |
+ MVPP2_GMAC_CONFIG_FULL_DUPLEX;
+ } else {
+ an |= MVPP2_GMAC_AN_SPEED_EN | MVPP2_GMAC_FLOW_CTRL_AUTONEG;
+ }
if (state->duplex)
an |= MVPP2_GMAC_CONFIG_FULL_DUPLEX;
@@ -8213,7 +8241,8 @@ static void mvpp2_gmac_config(struct mvpp2_port *port, unsigned int mode,
if (phylink_test(state->advertising, Asym_Pause))
an |= MVPP2_GMAC_FC_ADV_ASM_EN;
- if (state->interface == PHY_INTERFACE_MODE_SGMII) {
+ if (state->interface == PHY_INTERFACE_MODE_SGMII ||
+ state->interface == PHY_INTERFACE_MODE_1000BASEX) {
an |= MVPP2_GMAC_IN_BAND_AUTONEG;
ctrl2 |= MVPP2_GMAC_INBAND_AN_MASK | MVPP2_GMAC_PCS_ENABLE_MASK;
@@ -8275,7 +8304,8 @@ static void mvpp2_mac_config(struct net_device *dev, unsigned int mode,
if (state->interface == PHY_INTERFACE_MODE_10GKR)
mvpp2_xlg_config(port, mode, state);
else if (phy_interface_mode_is_rgmii(state->interface) ||
- state->interface == PHY_INTERFACE_MODE_SGMII)
+ state->interface == PHY_INTERFACE_MODE_SGMII ||
+ state->interface == PHY_INTERFACE_MODE_1000BASEX)
mvpp2_gmac_config(port, mode, state);
if (port->priv->hw_version == MVPP21 && port->flags & MVPP2_F_LOOPBACK)
--
2.14.3
next prev parent reply other threads:[~2018-03-16 10:35 UTC|newest]
Thread overview: 34+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-03-16 10:33 [PATCH net-next 00/10] net: mvpp2: phylink conversion Antoine Tenart
2018-03-16 10:33 ` [PATCH net-next 01/10] net: mvpp2: align the ethtool ops definition Antoine Tenart
2018-03-16 10:33 ` [PATCH net-next 02/10] net: phy: phylink: allow 10GKR interface to use in-band negotiation Antoine Tenart
2018-03-16 15:53 ` Russell King - ARM Linux
2018-03-19 8:52 ` Antoine Tenart
2018-03-19 11:12 ` Russell King - ARM Linux
2018-03-19 12:52 ` Antoine Tenart
2018-03-19 12:59 ` Andrew Lunn
2018-03-19 13:03 ` [EXT] " Stefan Chulski
2018-03-19 13:08 ` Andrew Lunn
2018-03-19 13:13 ` Antoine Tenart
2018-03-19 13:24 ` Andrew Lunn
2018-03-19 13:19 ` Stefan Chulski
2018-03-19 13:23 ` Andrew Lunn
2018-03-19 13:42 ` Russell King - ARM Linux
2018-03-19 13:10 ` Antoine Tenart
2018-03-19 13:18 ` Russell King - ARM Linux
2018-03-19 13:26 ` Antoine Tenart
2018-03-19 12:58 ` [EXT] " Stefan Chulski
2018-03-19 13:01 ` Yan Markman
2018-03-19 13:05 ` Russell King - ARM Linux
2018-03-16 10:33 ` [PATCH net-next 03/10] net: mvpp2: phylink support Antoine Tenart
2018-03-16 16:03 ` Russell King - ARM Linux
2018-03-19 8:45 ` Antoine Tenart
2018-03-16 10:33 ` [PATCH net-next 04/10] phy: add 2.5G SGMII mode to the phy_mode enum Antoine Tenart
2018-03-19 9:46 ` Kishon Vijay Abraham I
2018-03-16 10:33 ` [PATCH net-next 05/10] phy: cp110-comphy: 2.5G SGMII mode Antoine Tenart
2018-03-18 4:42 ` Baruch Siach
2018-03-19 8:44 ` Antoine Tenart
2018-03-16 10:33 ` Antoine Tenart [this message]
2018-03-16 10:33 ` [PATCH net-next 07/10] net: mvpp2: 2500baseX support Antoine Tenart
2018-03-16 10:33 ` [PATCH net-next 08/10] arm64: dts: marvell: 7040-db: set the 10G interface management to in-band Antoine Tenart
2018-03-16 10:33 ` [PATCH net-next 09/10] arm64: dts: marvell: 8040-db: set the 10G interfaces " Antoine Tenart
2018-03-16 10:33 ` [PATCH net-next 10/10] arm64: dts: marvell: mcbin: enable the fourth network interface Antoine Tenart
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180316103351.16616-7-antoine.tenart@bootlin.com \
--to=antoine.tenart@bootlin.com \
--cc=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=gregory.clement@bootlin.com \
--cc=jason@lakedaemon.net \
--cc=kishon@ti.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=maxime.chevallier@bootlin.com \
--cc=miquel.raynal@bootlin.com \
--cc=mw@semihalf.com \
--cc=nadavh@marvell.com \
--cc=netdev@vger.kernel.org \
--cc=sebastian.hesselbarth@gmail.com \
--cc=stefanc@marvell.com \
--cc=thomas.petazzoni@bootlin.com \
--cc=ymarkman@marvell.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®