mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Maxime Chevallier <maxime.chevallier@bootlin.com>
To: davem@davemloft.net
Cc: Yan Markman <ymarkman@marvell.com>,
	netdev@vger.kernel.org, linux-kernel@vger.kernel.org,
	Antoine Tenart <antoine.tenart@bootlin.com>,
	thomas.petazzoni@bootlin.com, gregory.clement@bootlin.com,
	miquel.raynal@bootlin.com, nadavh@marvell.com,
	stefanc@marvell.com, mw@semihalf.com,
	Maxime Chevallier <maxime.chevallier@bootlin.com>
Subject: [PATCH net-next] net: mvpp2: Use relaxed I/O in data path
Date: Tue, 27 Mar 2018 16:49:05 +0200	[thread overview]
Message-ID: <20180327144905.23499-1-maxime.chevallier@bootlin.com> (raw)

From: Yan Markman <ymarkman@marvell.com>

Use relaxed I/O on the hot path. This achieves significant performance
improvements. On a 10G link, this makes a basic iperf TCP test go from
an average of 4.5 Gbits/sec to about 9.40 Gbits/sec.

Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Maxime: Commit message, cosmetic changes]
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
David, this patch should not conflict with other the pending PPv2 series I sent
earlier ("[PATCH net-next 0/2] net: mvpp2: Remove unnecessary dynamic allocs")

 drivers/net/ethernet/marvell/mvpp2.c | 43 +++++++++++++++++++++++++-----------
 1 file changed, 30 insertions(+), 13 deletions(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2.c b/drivers/net/ethernet/marvell/mvpp2.c
index f8bc3d4a39ff..5a68e00e9c5b 100644
--- a/drivers/net/ethernet/marvell/mvpp2.c
+++ b/drivers/net/ethernet/marvell/mvpp2.c
@@ -1359,6 +1359,10 @@ static u32 mvpp2_read(struct mvpp2 *priv, u32 offset)
 	return readl(priv->swth_base[0] + offset);
 }
 
+static u32 mvpp2_read_relaxed(struct mvpp2 *priv, u32 offset)
+{
+	return readl_relaxed(priv->swth_base[0] + offset);
+}
 /* These accessors should be used to access:
  *
  * - per-CPU registers, where each CPU has its own copy of the
@@ -1407,6 +1411,18 @@ static u32 mvpp2_percpu_read(struct mvpp2 *priv, int cpu,
 	return readl(priv->swth_base[cpu] + offset);
 }
 
+static void mvpp2_percpu_write_relaxed(struct mvpp2 *priv, int cpu,
+				       u32 offset, u32 data)
+{
+	writel_relaxed(data, priv->swth_base[cpu] + offset);
+}
+
+static u32 mvpp2_percpu_read_relaxed(struct mvpp2 *priv, int cpu,
+				     u32 offset)
+{
+	return readl_relaxed(priv->swth_base[cpu] + offset);
+}
+
 static dma_addr_t mvpp2_txdesc_dma_addr_get(struct mvpp2_port *port,
 					    struct mvpp2_tx_desc *tx_desc)
 {
@@ -4488,8 +4504,8 @@ static inline void mvpp2_bm_pool_put(struct mvpp2_port *port, int pool,
 				<< MVPP22_BM_ADDR_HIGH_VIRT_RLS_SHIFT) &
 				MVPP22_BM_ADDR_HIGH_VIRT_RLS_MASK;
 
-		mvpp2_percpu_write(port->priv, cpu,
-				   MVPP22_BM_ADDR_HIGH_RLS_REG, val);
+		mvpp2_percpu_write_relaxed(port->priv, cpu,
+					   MVPP22_BM_ADDR_HIGH_RLS_REG, val);
 	}
 
 	/* MVPP2_BM_VIRT_RLS_REG is not interpreted by HW, and simply
@@ -4497,10 +4513,10 @@ static inline void mvpp2_bm_pool_put(struct mvpp2_port *port, int pool,
 	 * descriptor. Instead of storing the virtual address, we
 	 * store the physical address
 	 */
-	mvpp2_percpu_write(port->priv, cpu,
-			   MVPP2_BM_VIRT_RLS_REG, buf_phys_addr);
-	mvpp2_percpu_write(port->priv, cpu,
-			   MVPP2_BM_PHY_RLS_REG(pool), buf_dma_addr);
+	mvpp2_percpu_write_relaxed(port->priv, cpu,
+				   MVPP2_BM_VIRT_RLS_REG, buf_phys_addr);
+	mvpp2_percpu_write_relaxed(port->priv, cpu,
+				   MVPP2_BM_PHY_RLS_REG(pool), buf_dma_addr);
 
 	put_cpu();
 }
@@ -5592,7 +5608,8 @@ static int mvpp2_aggr_desc_num_check(struct mvpp2 *priv,
 	if ((aggr_txq->count + num) > MVPP2_AGGR_TXQ_SIZE) {
 		/* Update number of occupied aggregated Tx descriptors */
 		int cpu = smp_processor_id();
-		u32 val = mvpp2_read(priv, MVPP2_AGGR_TXQ_STATUS_REG(cpu));
+		u32 val = mvpp2_read_relaxed(priv,
+					     MVPP2_AGGR_TXQ_STATUS_REG(cpu));
 
 		aggr_txq->count = val & MVPP2_AGGR_TXQ_PENDING_MASK;
 	}
@@ -5616,9 +5633,9 @@ static int mvpp2_txq_alloc_reserved_desc(struct mvpp2 *priv,
 	int cpu = smp_processor_id();
 
 	val = (txq->id << MVPP2_TXQ_RSVD_REQ_Q_OFFSET) | num;
-	mvpp2_percpu_write(priv, cpu, MVPP2_TXQ_RSVD_REQ_REG, val);
+	mvpp2_percpu_write_relaxed(priv, cpu, MVPP2_TXQ_RSVD_REQ_REG, val);
 
-	val = mvpp2_percpu_read(priv, cpu, MVPP2_TXQ_RSVD_RSLT_REG);
+	val = mvpp2_percpu_read_relaxed(priv, cpu, MVPP2_TXQ_RSVD_RSLT_REG);
 
 	return val & MVPP2_TXQ_RSVD_RSLT_MASK;
 }
@@ -5723,8 +5740,8 @@ static inline int mvpp2_txq_sent_desc_proc(struct mvpp2_port *port,
 	u32 val;
 
 	/* Reading status reg resets transmitted descriptor counter */
-	val = mvpp2_percpu_read(port->priv, smp_processor_id(),
-				MVPP2_TXQ_SENT_REG(txq->id));
+	val = mvpp2_percpu_read_relaxed(port->priv, smp_processor_id(),
+					MVPP2_TXQ_SENT_REG(txq->id));
 
 	return (val & MVPP2_TRANSMITTED_COUNT_MASK) >>
 		MVPP2_TRANSMITTED_COUNT_OFFSET;
@@ -7090,8 +7107,8 @@ static int mvpp2_poll(struct napi_struct *napi, int budget)
 	 *
 	 * Each CPU has its own Rx/Tx cause register
 	 */
-	cause_rx_tx = mvpp2_percpu_read(port->priv, qv->sw_thread_id,
-					MVPP2_ISR_RX_TX_CAUSE_REG(port->id));
+	cause_rx_tx = mvpp2_percpu_read_relaxed(port->priv, qv->sw_thread_id,
+						MVPP2_ISR_RX_TX_CAUSE_REG(port->id));
 
 	cause_misc = cause_rx_tx & MVPP2_CAUSE_MISC_SUM_MASK;
 	if (cause_misc) {
-- 
2.11.0

             reply	other threads:[~2018-03-27 14:50 UTC|newest]

Thread overview: 3+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-03-27 14:49 Maxime Chevallier [this message]
2018-03-27 17:16 ` David Miller
2018-03-27 17:18   ` [EXT] " Yan Markman

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20180327144905.23499-1-maxime.chevallier@bootlin.com \
    --to=maxime.chevallier@bootlin.com \
    --cc=antoine.tenart@bootlin.com \
    --cc=davem@davemloft.net \
    --cc=gregory.clement@bootlin.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=miquel.raynal@bootlin.com \
    --cc=mw@semihalf.com \
    --cc=nadavh@marvell.com \
    --cc=netdev@vger.kernel.org \
    --cc=stefanc@marvell.com \
    --cc=thomas.petazzoni@bootlin.com \
    --cc=ymarkman@marvell.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®