From: Jon Mason <jdmason@kudzu.us>
To: Serge Semin <fancer.lancer@gmail.com>
Cc: dave.jiang@intel.com, allenbh@gmail.com,
Sergey.Semin@t-platforms.ru, linux-ntb@googlegroups.com,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH 0/4] ntb: idt: Add hwmon temperature sensor interface
Date: Wed, 31 Oct 2018 17:27:22 -0400 [thread overview]
Message-ID: <20181031212721.GA2565@kudzu.us> (raw)
In-Reply-To: <20180714115834.3350-1-fancer.lancer@gmail.com>
On Sat, Jul 14, 2018 at 02:58:30PM +0300, Serge Semin wrote:
> IDT PCIe-switches are equipped with an embedded temperature sensor. It
> works within the range [0; 127.5]C with a resolution of 0.5C. It can
> be used to monitor the chip core temperature so to have prevent it from
> possible overheating. It might be very topical for the chip, since it
> gets heated like in hell especially if ASPM isn't enabled.
>
> Other than the current sampled temperatur, the sensor interface exposes
> history registors with lowest and highest measured temperature, thresholds
> and alarm IRQs enabled/disable bits, ADC/filter settings. The device manual
> states that the switch is able to generate a msi interrupt on PCIe upstreams
> if the temperature crosses one of three configurable thresholds. But in
> practice we discovered that the enable/disable threshold IRQs bits interface
> is very broken (see the third patch commit message), so it can't be used
> to create the hwmon alarm interface. As the result we had to remove the
> already available temperature sensor IRQ handler and disable the corresponding
> interrupt.
>
> Current version of the driver provides following standard hwmon sysfs
> files: temperature input, lowest and highest measured temperature
> with possibility to reset the history, temperature offset. The rest of the
> nodes can't be safely implemented for the chip due to the described issues.
>
> Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
FYI, I'm waiting on you to correct the kbuild issues. I have been
assuming you knew this, but given the lack of follow-up patches I am
beginning to this you might believe I'm ignoring them. I'm not :)
Thanks,
Jon
>
> Serge Semin (4):
> ntb: idt: Alter temperature read method
> ntb: idt: Add basic hwmon sysfs interface
> ntb: idt: Discard temperature sensor IRQ handler
> ntb: idt: Alter the driver info comments
>
> drivers/ntb/hw/idt/Kconfig | 4 +-
> drivers/ntb/hw/idt/ntb_hw_idt.c | 317 ++++++++++++++++++++++++++++++++++------
> drivers/ntb/hw/idt/ntb_hw_idt.h | 87 ++++++++++-
> 3 files changed, 353 insertions(+), 55 deletions(-)
>
> --
> 2.12.0
>
prev parent reply other threads:[~2018-10-31 21:27 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-07-14 11:58 Serge Semin
2018-07-14 11:58 ` [PATCH 1/4] ntb: idt: Alter temperature read method Serge Semin
2018-07-14 11:58 ` [PATCH 2/4] ntb: idt: Add basic hwmon sysfs interface Serge Semin
2018-07-17 1:28 ` kbuild test robot
2018-07-17 1:28 ` kbuild test robot
2018-07-14 11:58 ` [PATCH 3/4] ntb: idt: Discard temperature sensor IRQ handler Serge Semin
2018-07-14 11:58 ` [PATCH 4/4] ntb: idt: Alter the driver info comments Serge Semin
2018-07-17 9:24 ` [PATCH v2 0/4] ntb: idt: Add hwmon temperature sensor interface Serge Semin
2018-07-17 9:24 ` [PATCH v2 1/4] ntb: idt: Alter temperature read method Serge Semin
2018-07-17 9:24 ` [PATCH v2 2/4] ntb: idt: Add basic hwmon sysfs interface Serge Semin
2018-07-17 9:24 ` [PATCH v2 3/4] ntb: idt: Discard temperature sensor IRQ handler Serge Semin
2018-07-17 9:24 ` [PATCH v2 4/4] ntb: idt: Alter the driver info comments Serge Semin
2018-11-01 14:35 ` [PATCH v2 0/4] ntb: idt: Add hwmon temperature sensor interface Jon Mason
2018-10-31 21:27 ` Jon Mason [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20181031212721.GA2565@kudzu.us \
--to=jdmason@kudzu.us \
--cc=Sergey.Semin@t-platforms.ru \
--cc=allenbh@gmail.com \
--cc=dave.jiang@intel.com \
--cc=fancer.lancer@gmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-ntb@googlegroups.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
Powered by JetHome