From: Karl Palsson <karlp@tweak.net.au>
To: robh+dt@kernel.org, mark.rutland@arm.com,
maxime.ripard@bootlin.com, wens@csie.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org
Cc: Karl Palsson <karlp@tweak.net.au>
Subject: [PATCH 2/3] ARM: dts: sun8i: add FriendlyARM NanoPi Duo2
Date: Tue, 18 Dec 2018 21:24:56 +0000 [thread overview]
Message-ID: <20181218212457.30382-2-karlp@tweak.net.au> (raw)
In-Reply-To: <20181218212457.30382-1-karlp@tweak.net.au>
This is an Allwinner H3 based board, with 512MB ram, a USB OTG port,
microsd slot, an onboard AP6212A wifi/bluetooth module, and a CSI
connector.
Full details and schematic available from vendor:
http://wiki.friendlyarm.com/wiki/index.php/NanoPi_Duo2
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dts | 148 +++++++++++++++++++++++++++++
2 files changed, 149 insertions(+)
create mode 100644 arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 78551c4375d5..7f296bfea94a 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1063,6 +1063,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-h3-beelink-x2.dtb \
sun8i-h3-libretech-all-h3-cc.dtb \
sun8i-h3-mapleboard-mp130.dtb \
+ sun8i-h3-nanopi-duo2.dtb \
sun8i-h3-nanopi-m1.dtb \
sun8i-h3-nanopi-m1-plus.dtb \
sun8i-h3-nanopi-neo.dtb \
diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dts
new file mode 100644
index 000000000000..07d2f1bebd56
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dts
@@ -0,0 +1,148 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2018 Karl Palsson <karlp@tweak.net.au>
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "FriendlyARM NanoPi Duo2";
+ compatible = "friendlyarm,nanopi-duo2", "allwinner,sun8i-h3";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ status {
+ label = "nanopi:green:status";
+ gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ pwr {
+ label = "nanopi:red:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+
+ r_gpio_keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&sw_r_npi>;
+
+ k1 {
+ label = "k1";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ reg_vdd_cpux: vdd-cpux-regulator {
+ compatible = "regulator-gpio";
+ regulator-name = "vdd-cpux";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-ramp-delay = <50>; /* 4ms */
+
+ gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+ enable-active-high;
+ gpios-states = <0x1>;
+ states = <1100000 0x0
+ 1300000 0x1>;
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+ };
+
+};
+
+&cpu0 {
+ cpu-supply = <®_vdd_cpux>;
+};
+
+&usb_otg {
+ status = "okay";
+ dr_mode = "otg";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+®_usb0_vbus {
+ gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
+ status = "okay";
+};
+
+&r_pio {
+ sw_r_npi: key_pins {
+ pins = "PL3";
+ function = "gpio_in";
+ };
+};
+
+&usbphy {
+ usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+ usb0_vbus-supply = <®_usb0_vbus>;
+ status = "okay";
+};
+
+&mmc0 {
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+ status = "okay";
+ vmmc-supply = <®_vcc3v3>;
+};
+
+&mmc1 {
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ sdio_wifi: sdio_wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&pio>;
+ interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
+ interrupt-names = "host-wake";
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>, <&uart2_rts_cts_pins>;
+ uart-has-rtscts;
+ status = "okay";
+
+ /* bluetooth goes here */
+};
--
2.14.5
next prev parent reply other threads:[~2018-12-18 21:35 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-12-18 21:24 [PATCH 1/3] ARM: dts: sunxi: h3/h5: add missing uart2 rts/cts pins Karl Palsson
2018-12-18 21:24 ` Karl Palsson [this message]
2018-12-19 7:08 ` [PATCH 2/3] ARM: dts: sun8i: add FriendlyARM NanoPi Duo2 Maxime Ripard
2018-12-18 21:24 ` [PATCH 3/3] ARM: dts: sun8i: add FriendlyARM NanoPi Duo2-IoT Box Karl Palsson
2019-10-31 23:12 [PATCH 2/3] ARM: dts: sun8i: add FriendlyARM NanoPi Duo2 Karl Palsson
2019-11-01 3:01 ` Chen-Yu Tsai
2019-11-01 10:00 ` Karl Palsson
2019-11-01 9:08 ` Maxime Ripard
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20181218212457.30382-2-karlp@tweak.net.au \
--to=karlp@tweak.net.au \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=maxime.ripard@bootlin.com \
--cc=robh+dt@kernel.org \
--cc=wens@csie.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®