From: Brian Masney <masneyb@onstation.org>
To: linus.walleij@linaro.org, sboyd@kernel.org,
bjorn.andersson@linaro.org, andy.gross@linaro.org,
marc.zyngier@arm.com, lee.jones@linaro.org
Cc: tglx@linutronix.de, shawnguo@kernel.org, dianders@chromium.org,
linux-gpio@vger.kernel.org, nicolas.dechesne@linaro.org,
niklas.cassel@linaro.org, david.brown@linaro.org,
robh+dt@kernel.org, mark.rutland@arm.com,
thierry.reding@gmail.com, linux-arm-msm@vger.kernel.org,
linux-kernel@vger.kernel.org, devicetree@vger.kernel.org
Subject: [PATCH 6/9] arm: dts: qcom: apq8064: add interrupt controller properties
Date: Fri, 25 Jan 2019 11:22:59 -0500 [thread overview]
Message-ID: <20190125162302.14036-7-masneyb@onstation.org> (raw)
In-Reply-To: <20190125162302.14036-1-masneyb@onstation.org>
Add interrupt controller properties now that ssbi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.
This change was not tested on any hardware but the same change was
tested on qcom-pm8941.dtsi with spmi-gpio using a LG Nexus 5
(hammerhead) phone with no issues.
Signed-off-by: Brian Masney <masneyb@onstation.org>
---
arch/arm/boot/dts/qcom-apq8064.dtsi | 46 ++---------------------------
1 file changed, 2 insertions(+), 44 deletions(-)
diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi
index 48c3cf427610..4744fe757cf4 100644
--- a/arch/arm/boot/dts/qcom-apq8064.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8064.dtsi
@@ -705,50 +705,8 @@
compatible = "qcom,pm8921-gpio",
"qcom,ssbi-gpio";
reg = <0x150>;
- interrupts = <192 IRQ_TYPE_NONE>,
- <193 IRQ_TYPE_NONE>,
- <194 IRQ_TYPE_NONE>,
- <195 IRQ_TYPE_NONE>,
- <196 IRQ_TYPE_NONE>,
- <197 IRQ_TYPE_NONE>,
- <198 IRQ_TYPE_NONE>,
- <199 IRQ_TYPE_NONE>,
- <200 IRQ_TYPE_NONE>,
- <201 IRQ_TYPE_NONE>,
- <202 IRQ_TYPE_NONE>,
- <203 IRQ_TYPE_NONE>,
- <204 IRQ_TYPE_NONE>,
- <205 IRQ_TYPE_NONE>,
- <206 IRQ_TYPE_NONE>,
- <207 IRQ_TYPE_NONE>,
- <208 IRQ_TYPE_NONE>,
- <209 IRQ_TYPE_NONE>,
- <210 IRQ_TYPE_NONE>,
- <211 IRQ_TYPE_NONE>,
- <212 IRQ_TYPE_NONE>,
- <213 IRQ_TYPE_NONE>,
- <214 IRQ_TYPE_NONE>,
- <215 IRQ_TYPE_NONE>,
- <216 IRQ_TYPE_NONE>,
- <217 IRQ_TYPE_NONE>,
- <218 IRQ_TYPE_NONE>,
- <219 IRQ_TYPE_NONE>,
- <220 IRQ_TYPE_NONE>,
- <221 IRQ_TYPE_NONE>,
- <222 IRQ_TYPE_NONE>,
- <223 IRQ_TYPE_NONE>,
- <224 IRQ_TYPE_NONE>,
- <225 IRQ_TYPE_NONE>,
- <226 IRQ_TYPE_NONE>,
- <227 IRQ_TYPE_NONE>,
- <228 IRQ_TYPE_NONE>,
- <229 IRQ_TYPE_NONE>,
- <230 IRQ_TYPE_NONE>,
- <231 IRQ_TYPE_NONE>,
- <232 IRQ_TYPE_NONE>,
- <233 IRQ_TYPE_NONE>,
- <234 IRQ_TYPE_NONE>,
- <235 IRQ_TYPE_NONE>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
gpio-controller;
#gpio-cells = <2>;
--
2.17.2
next prev parent reply other threads:[~2019-01-25 16:23 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-01-25 16:22 [PATCH 0/9] qcom: ssbi-gpio: add support for hierarchical IRQ chip Brian Masney
2019-01-25 16:22 ` [PATCH 1/9] pinctrl: qcom: ssbi-gpio: hardcode IRQ counts Brian Masney
2019-02-06 9:38 ` Linus Walleij
2019-02-06 12:01 ` Linus Walleij
2019-01-25 16:22 ` [PATCH 2/9] genirq: introduce irq_domain_translate_twocell Brian Masney
2019-01-30 13:54 ` Marc Zyngier
2019-01-25 16:22 ` [PATCH 3/9] mfd: pm8xxx: convert to v2 irq interfaces to support hierarchical IRQ chips Brian Masney
2019-01-30 13:27 ` Lee Jones
2019-02-04 10:20 ` Brian Masney
2019-02-06 10:02 ` Linus Walleij
2019-02-06 13:07 ` Linus Walleij
2019-02-06 14:10 ` Brian Masney
2019-02-06 14:37 ` Linus Walleij
2019-01-25 16:22 ` [PATCH 4/9] mfd: pm8xxx: disassociate old virq if hwirq mapping already exists Brian Masney
2019-01-30 13:31 ` Lee Jones
2019-01-25 16:22 ` [PATCH 5/9] qcom: ssbi-gpio: add support for hierarchical IRQ chip Brian Masney
2019-01-25 16:22 ` Brian Masney [this message]
2019-01-25 16:23 ` [PATCH 7/9] arm: dts: qcom: msm8660: add interrupt controller properties Brian Masney
2019-01-25 16:23 ` [PATCH 8/9] arm: dts: qcom: mdm9615: " Brian Masney
2019-01-25 16:23 ` [PATCH 9/9] mfd: pm8xxx: revert "disassociate old virq if hwirq mapping already exists" Brian Masney
2019-02-06 15:21 ` [PATCH 0/9] qcom: ssbi-gpio: add support for hierarchical IRQ chip Linus Walleij
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190125162302.14036-7-masneyb@onstation.org \
--to=masneyb@onstation.org \
--cc=andy.gross@linaro.org \
--cc=bjorn.andersson@linaro.org \
--cc=david.brown@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=dianders@chromium.org \
--cc=lee.jones@linaro.org \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=marc.zyngier@arm.com \
--cc=mark.rutland@arm.com \
--cc=nicolas.dechesne@linaro.org \
--cc=niklas.cassel@linaro.org \
--cc=robh+dt@kernel.org \
--cc=sboyd@kernel.org \
--cc=shawnguo@kernel.org \
--cc=tglx@linutronix.de \
--cc=thierry.reding@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®