From: Raul E Rangel <rrangel@chromium.org>
To: linux-mmc@vger.kernel.org
Cc: djkurtz@chromium.org, zwisler@chromium.org,
Raul E Rangel <rrangel@chromium.org>,
Avri Altman <avri.altman@wdc.com>,
hongjiefang <hongjiefang@asrmicro.com>,
linux-kernel@vger.kernel.org,
Shawn Lin <shawn.lin@rock-chips.com>,
Kyle Roeschley <kyle.roeschley@ni.com>,
Ulf Hansson <ulf.hansson@linaro.org>
Subject: [PATCH v2] mmc: core: Verify SD bus width
Date: Tue, 16 Apr 2019 12:57:05 -0600 [thread overview]
Message-ID: <20190416185705.256369-1-rrangel@chromium.org> (raw)
The SD Physical Layer Spec says the following: Since the SD Memory Card
shall support at least the two bus modes 1-bit or 4-bit width, then any SD
Card shall set at least bits 0 and 2 (SD_BUS_WIDTH="0101").
This change verifies the card has specified a bus width.
AMD SDHC Device 7806 can get into a bad state after a card disconnect
where anything transferred via the DATA lines will always result in a
zero filled buffer. Currently the driver will continue without error if
the HC is in this condition. A block device will be created, but reading
from it will result in a zero buffer. This makes it seem like the SD
device has been erased, when in actuality the data is never getting
copied from the DATA lines to the data buffer.
SCR is the first command in the SD initialization sequence that uses the
DATA lines. By checking that the response was invalid, we can abort
mounting the card.
Acked-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
---
This patch currently requires the SD trace events patch to be applied
first for it to apply cleanly.
See: https://patchwork.kernel.org/cover/10903761
This is because I want the check to happen after the trace call. This
way the invalid valid response is traced.
I can also change the base so it applies cleanly to master if that is
desired.
Here is the testing I did:
Good Trace: https://paste.fedoraproject.org/paste/oVEI5b0IzHD23Yo7CDZgEg
[ 30.103686] mmc0: new high speed SDHC card at address 0001
[ 30.105262] mmcblk0: mmc0:0001 00000 7.41 GiB
[ 30.108258] mmcblk0: p1
[ 31.947250] mmc0: card 0001 removed
Bad Trace (before patch): https://paste.fedoraproject.org/paste/jBWfpFBM8gdEmGOzxij~hw
Bad Trace (after patch): https://paste.fedoraproject.org/paste/8gB8MLYOKEUZEgHXmQ0W1Q
[ 33.810760] mmc0: invalid bus width
[ 33.810782] mmc0: error -22 whilst initialising SD card
[ 34.068818] mmc0: invalid bus width
[ 34.068839] mmc0: error -22 whilst initialising SD card
[ 34.329521] mmc0: invalid bus width
[ 34.329543] mmc0: error -22 whilst initialising SD card
[ 34.592061] mmc0: invalid bus width
[ 34.592084] mmc0: error -22 whilst initialising SD card
In the traces you can see sd_scr is different
Changes in v2:
- Made the bus width check stricter. It now requires the value to match
the spec.
- Rebased on SD Trace Event patch
drivers/mmc/core/sd.c | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c
index 3b2e09fa72c5..a73f3dbb6029 100644
--- a/drivers/mmc/core/sd.c
+++ b/drivers/mmc/core/sd.c
@@ -229,6 +229,13 @@ static int mmc_decode_scr(struct mmc_card *card)
trace_sd_scr(card, scr);
+ /* SD Spec says: any SD Card shall set at least bits 0 and 2 */
+ if (!(scr->bus_widths & SD_SCR_BUS_WIDTH_1) ||
+ !(scr->bus_widths & SD_SCR_BUS_WIDTH_4)) {
+ pr_err("%s: invalid bus width\n", mmc_hostname(card->host));
+ return -EINVAL;
+ }
+
return 0;
}
--
2.21.0.392.gf8f6787159e-goog
next reply other threads:[~2019-04-16 18:57 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-04-16 18:57 Raul E Rangel [this message]
2019-04-18 6:20 ` Avri Altman
2019-04-24 15:56 ` Raul Rangel
2019-04-29 10:00 ` Ulf Hansson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190416185705.256369-1-rrangel@chromium.org \
--to=rrangel@chromium.org \
--cc=avri.altman@wdc.com \
--cc=djkurtz@chromium.org \
--cc=hongjiefang@asrmicro.com \
--cc=kyle.roeschley@ni.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=shawn.lin@rock-chips.com \
--cc=ulf.hansson@linaro.org \
--cc=zwisler@chromium.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®