From: Faiz Abbas <faiz_abbas@ti.com>
To: <linux-kernel@vger.kernel.org>, <devicetree@vger.kernel.org>,
<linux-omap@vger.kernel.org>
Cc: <mark.rutland@arm.com>, <robh+dt@kernel.org>, <tony@atomide.com>,
<bcousson@baylibre.com>, <ulf.hansson@linaro.org>,
<adrian.hunter@intel.com>
Subject: [PATCH] ARM: dts: am57xx-idk: Remove support for voltage switching for SD card
Date: Thu, 2 May 2019 14:17:48 +0530 [thread overview]
Message-ID: <20190502084748.22518-1-faiz_abbas@ti.com> (raw)
If UHS speed modes are enabled, a compatible SD card switches down to
1.8V during enumeration. If after this a software reboot/crash takes
place and on-chip ROM tries to enumerate the SD card, the difference in
IO voltages (host @ 3.3V and card @ 1.8V) may end up damaging the card.
The fix for this is to have support for power cycling the card in
hardware (with a PORz/soft-reset line causing a power cycle of the
card). Since am571x-, am572x- and am574x-idk don't have this
capability, disable voltage switching for these boards.
The major effect of this is that the maximum supported speed
mode is now high speed(50 MHz) down from SDR104(200 MHz).
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
---
arch/arm/boot/dts/am57xx-idk-common.dtsi | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/boot/dts/am57xx-idk-common.dtsi b/arch/arm/boot/dts/am57xx-idk-common.dtsi
index f7bd26458915..42e433da79ec 100644
--- a/arch/arm/boot/dts/am57xx-idk-common.dtsi
+++ b/arch/arm/boot/dts/am57xx-idk-common.dtsi
@@ -420,6 +420,7 @@
vqmmc-supply = <&ldo1_reg>;
bus-width = <4>;
cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; /* gpio 219 */
+ no-1-8-v;
};
&mmc2 {
--
2.19.2
next reply other threads:[~2019-05-02 8:47 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-05-02 8:47 Faiz Abbas [this message]
2019-05-02 14:20 ` Tony Lindgren
2019-05-02 14:30 ` Faiz Abbas
2019-05-02 14:35 ` Tony Lindgren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190502084748.22518-1-faiz_abbas@ti.com \
--to=faiz_abbas@ti.com \
--cc=adrian.hunter@intel.com \
--cc=bcousson@baylibre.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=tony@atomide.com \
--cc=ulf.hansson@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®