From: Bjorn Andersson <bjorn.andersson@linaro.org>
To: Andy Gross <agross@kernel.org>, David Brown <david.brown@linaro.org>
Cc: Ohad Ben-Cohen <ohad@wizery.com>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
linux-arm-msm@vger.kernel.org, linux-remoteproc@vger.kernel.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: [PATCH v2 5/8] arm64: dts: qcom: qcs404: Fully describe the CDSP
Date: Thu, 9 May 2019 21:34:18 -0700 [thread overview]
Message-ID: <20190510043421.31393-6-bjorn.andersson@linaro.org> (raw)
In-Reply-To: <20190510043421.31393-1-bjorn.andersson@linaro.org>
Add all the properties needed to describe the CDSP for both the
Trustzone and non-Trustzone based remoteproc case, allowing any child
devices to be described once by just overriding the compatible to match
the firmware available on the board.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
arch/arm64/boot/dts/qcom/qcs404.dtsi | 82 +++++++++++++++++-----------
1 file changed, 51 insertions(+), 31 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/qcs404.dtsi b/arch/arm64/boot/dts/qcom/qcs404.dtsi
index 3eb6089c8024..896f95817f23 100644
--- a/arch/arm64/boot/dts/qcom/qcs404.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404.dtsi
@@ -113,37 +113,6 @@
};
};
- remoteproc_cdsp: remoteproc-cdsp {
- compatible = "qcom,qcs404-cdsp-pas";
-
- interrupts-extended = <&intc GIC_SPI 229 IRQ_TYPE_EDGE_RISING>,
- <&cdsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
- <&cdsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
- <&cdsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
- <&cdsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
- interrupt-names = "wdog", "fatal", "ready",
- "handover", "stop-ack";
-
- clocks = <&xo_board>;
- clock-names = "xo";
-
- memory-region = <&cdsp_fw_mem>;
-
- qcom,smem-states = <&cdsp_smp2p_out 0>;
- qcom,smem-state-names = "stop";
-
- status = "disabled";
-
- glink-edge {
- interrupts = <GIC_SPI 141 IRQ_TYPE_EDGE_RISING>;
-
- qcom,remote-pid = <5>;
- mboxes = <&apcs_glb 12>;
-
- label = "cdsp";
- };
- };
-
remoteproc_wcss: remoteproc-wcss {
compatible = "qcom,qcs404-wcss-pas";
@@ -288,6 +257,57 @@
clock-names = "core";
};
+ remoteproc_cdsp: remoteproc@b00000 {
+ compatible = "qcom,qcs404-cdsp-pas";
+ reg = <0x00b00000 0x4040>;
+
+ interrupts-extended = <&intc GIC_SPI 229 IRQ_TYPE_EDGE_RISING>,
+ <&cdsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&cdsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&cdsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&cdsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog", "fatal", "ready",
+ "handover", "stop-ack";
+
+ clocks = <&xo_board>,
+ <&gcc GCC_CDSP_CFG_AHB_CLK>,
+ <&gcc GCC_CDSP_TBU_CLK>,
+ <&gcc GCC_BIMC_CDSP_CLK>,
+ <&turingcc TURING_WRAPPER_AON_CLK>,
+ <&turingcc TURING_Q6SS_AHBS_AON_CLK>,
+ <&turingcc TURING_Q6SS_AHBM_AON_CLK>,
+ <&turingcc TURING_Q6SS_Q6_AXIM_CLK>;
+ clock-names = "xo",
+ "sway",
+ "tbu",
+ "bimc",
+ "ahb_aon",
+ "q6ss_slave",
+ "q6ss_master",
+ "q6_axim";
+
+ resets = <&gcc GCC_CDSP_RESTART>;
+ reset-names = "restart";
+
+ qcom,halt-regs = <&tcsr 0x19004>;
+
+ memory-region = <&cdsp_fw_mem>;
+
+ qcom,smem-states = <&cdsp_smp2p_out 0>;
+ qcom,smem-state-names = "stop";
+
+ status = "disabled";
+
+ glink-edge {
+ interrupts = <GIC_SPI 141 IRQ_TYPE_EDGE_RISING>;
+
+ qcom,remote-pid = <5>;
+ mboxes = <&apcs_glb 12>;
+
+ label = "cdsp";
+ };
+ };
+
tlmm: pinctrl@1000000 {
compatible = "qcom,qcs404-pinctrl";
reg = <0x01000000 0x200000>,
--
2.18.0
next prev parent reply other threads:[~2019-05-10 4:34 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-05-10 4:34 [PATCH v2 0/8] Qualcomm QCS404 CDSP improvements and fastrpc Bjorn Andersson
2019-05-10 4:34 ` [PATCH v2 1/8] dt-bindings: remoteproc: Rename and amend Hexagon v56 binding Bjorn Andersson
2019-05-13 15:23 ` Rob Herring
2019-05-10 4:34 ` [PATCH v2 2/8] remoteproc: qcom: qdsp6-adsp: Add support for QCS404 CDSP Bjorn Andersson
2019-05-10 4:34 ` [PATCH v2 3/8] arm64: dts: qcom: qcs404-evb: Mark CDSP clocks protected Bjorn Andersson
2019-05-10 4:34 ` [PATCH v2 4/8] arm64: dts: qcom: qcs404: Add TCSR node Bjorn Andersson
2019-05-10 4:34 ` Bjorn Andersson [this message]
2019-05-10 4:34 ` [PATCH v2 6/8] arm64: dts: qcom: qcs404: Move lpass and q6 into soc Bjorn Andersson
2019-05-10 4:34 ` [PATCH v2 7/8] arm64: dts: qcom: qcs404: Define APPS IOMMU Bjorn Andersson
2019-05-13 4:54 ` Vinod Koul
2019-05-13 18:28 ` Bjorn Andersson
2019-05-10 4:34 ` [PATCH v2 8/8] arm64: dts: qcom: qcs404: Add fastrpc nodes Bjorn Andersson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190510043421.31393-6-bjorn.andersson@linaro.org \
--to=bjorn.andersson@linaro.org \
--cc=agross@kernel.org \
--cc=david.brown@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-remoteproc@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=ohad@wizery.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®