From: Vinod Koul <vkoul@kernel.org>
To: Niklas Cassel <niklas.cassel@linaro.org>
Cc: Andy Gross <agross@kernel.org>,
linux-arm-msm@vger.kernel.org,
Bjorn Andersson <bjorn.andersson@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Stephen Boyd <sboyd@kernel.org>,
Sibi Sankar <sibis@codeaurora.org>,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH v2 2/8] arm64: dts: qcom: pm8150: Add Base DTS file
Date: Tue, 20 Aug 2019 18:04:43 +0530 [thread overview]
Message-ID: <20190820123443.GA12733@vkoul-mobl.Dlink> (raw)
In-Reply-To: <20190820122719.GD31261@centauri>
On 20-08-19, 14:27, Niklas Cassel wrote:
> On Tue, Aug 20, 2019 at 12:12:10PM +0530, Vinod Koul wrote:
> > Add base DTS file for pm8150 along with GPIOs, power-on, rtc and vadc
> > nodes
> >
> > Signed-off-by: Vinod Koul <vkoul@kernel.org>
> > ---
> > arch/arm64/boot/dts/qcom/pm8150.dtsi | 95 ++++++++++++++++++++++++++++
> > 1 file changed, 95 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/qcom/pm8150.dtsi
> >
> > diff --git a/arch/arm64/boot/dts/qcom/pm8150.dtsi b/arch/arm64/boot/dts/qcom/pm8150.dtsi
> > new file mode 100644
> > index 000000000000..4a678be46d37
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/qcom/pm8150.dtsi
> > @@ -0,0 +1,95 @@
> > +// SPDX-License-Identifier: BSD-3-Clause
> > +// Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
> > +// Copyright (c) 2019, Linaro Limited
> > +
> > +#include <dt-bindings/input/input.h>
> > +#include <dt-bindings/interrupt-controller/irq.h>
> > +#include <dt-bindings/spmi/spmi.h>
> > +#include <dt-bindings/iio/qcom,spmi-vadc.h>
> > +
> > +&spmi_bus {
> > + pm8150_0: pmic@0 {
> > + compatible = "qcom,pm8150", "qcom,spmi-pmic";
> > + reg = <0x0 SPMI_USID>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + pon: power-on@800 {
> > + compatible = "qcom,pm8916-pon";
> > + reg = <0x0800>;
> > + pwrkey {
> > + compatible = "qcom,pm8941-pwrkey";
> > + interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
>
> Here you use 0 for 3rd cell
>
> > + debounce = <15625>;
> > + bias-pull-up;
> > + linux,code = <KEY_POWER>;
> > +
> > + status = "disabled";
> > + };
> > + };
> > +
> > + pm8150_adc: adc@3100 {
> > + compatible = "qcom,spmi-adc5";
> > + reg = <0x3100>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + #io-channel-cells = <1>;
> > + interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
>
> Here you use 0x0 for 3rd cell, be consistent.
Will make it either at this and other places, thanks for pointing!
--
~Vinod
next prev parent reply other threads:[~2019-08-20 12:35 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-08-20 6:42 [PATCH v2 0/8] arm64: dts: qcom: sm8150: Add SM8150 DTS Vinod Koul
2019-08-20 6:42 ` [PATCH v2 1/8] arm64: dts: qcom: sm8150: add base dts file Vinod Koul
2019-08-20 12:27 ` Niklas Cassel
2019-08-20 12:33 ` Vinod Koul
2019-08-20 13:33 ` Amit Kucheria
2019-08-20 16:37 ` Vinod Koul
2019-08-20 6:42 ` [PATCH v2 2/8] arm64: dts: qcom: pm8150: Add Base DTS file Vinod Koul
2019-08-20 12:27 ` Niklas Cassel
2019-08-20 12:34 ` Vinod Koul [this message]
2019-08-20 6:42 ` [PATCH v2 3/8] arm64: dts: qcom: pm8150b: " Vinod Koul
2019-08-20 12:27 ` Niklas Cassel
2019-08-20 12:35 ` Vinod Koul
2019-08-20 6:42 ` [PATCH v2 4/8] arm64: dts: qcom: pm8150l: " Vinod Koul
2019-08-20 6:42 ` [PATCH v2 5/8] arm64: dts: qcom: sm8150-mtp: add base dts file Vinod Koul
2019-08-20 12:26 ` Niklas Cassel
2019-08-20 12:36 ` Vinod Koul
2019-08-20 6:42 ` [PATCH v2 6/8] arm64: dts: qcom: sm8150-mtp: Add regulators Vinod Koul
2019-08-20 12:26 ` Niklas Cassel
2019-08-20 12:37 ` Vinod Koul
2019-08-20 6:42 ` [PATCH v2 7/8] arm64: dts: qcom: sm8150: Add reserved-memory regions Vinod Koul
2019-08-20 12:24 ` Niklas Cassel
2019-08-20 6:42 ` [PATCH v2 8/8] arm64: dts: qcom: sm8150: Add apps shared nodes Vinod Koul
2019-08-20 12:28 ` [PATCH v2 0/8] arm64: dts: qcom: sm8150: Add SM8150 DTS Niklas Cassel
2019-08-20 12:39 ` Vinod Koul
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190820123443.GA12733@vkoul-mobl.Dlink \
--to=vkoul@kernel.org \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=niklas.cassel@linaro.org \
--cc=robh+dt@kernel.org \
--cc=sboyd@kernel.org \
--cc=sibis@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®