mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Biao Huang <biao.huang@mediatek.com>
To: <davem@davemloft.net>, Rob Herring <robh+dt@kernel.org>,
	Andrew Lunn <andrew@lunn.ch>
Cc: Mark Rutland <mark.rutland@arm.com>,
	Giuseppe Cavallaro <peppe.cavallaro@st.com>,
	Alexandre Torgue <alexandre.torgue@st.com>,
	Jose Abreu <joabreu@synopsys.com>,
	Maxime Coquelin <mcoquelin.stm32@gmail.com>,
	Matthias Brugger <matthias.bgg@gmail.com>,
	Biao Huang <biao.huang@mediatek.com>, <netdev@vger.kernel.org>,
	<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
	<linux-stm32@st-md-mailman.stormreply.com>,
	<linux-arm-kernel@lists.infradead.org>,
	<linux-mediatek@lists.infradead.org>, <yt.shen@mediatek.com>
Subject: [v2, PATCH 1/2] net-next: stmmac: mediatek: add more support for RMII
Date: Mon, 16 Dec 2019 13:39:57 +0800	[thread overview]
Message-ID: <20191216053958.26130-2-biao.huang@mediatek.com> (raw)
In-Reply-To: <20191216053958.26130-1-biao.huang@mediatek.com>

MT2712 SoC can provide the rmii reference clock, and the clock
will output from TXC pin only, which means ref_clk pin of external
PHY should connect to TXC pin in this case.
Add corresponding clock and timing settings.

Signed-off-by: Biao Huang <biao.huang@mediatek.com>
---
 .../ethernet/stmicro/stmmac/dwmac-mediatek.c  | 89 +++++++++++++------
 1 file changed, 60 insertions(+), 29 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
index bdb80421acac..9e4b83832938 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
@@ -55,6 +55,8 @@ struct mediatek_dwmac_plat_data {
 	struct regmap *peri_regmap;
 	struct device *dev;
 	phy_interface_t phy_mode;
+	int num_clks_to_config;
+	bool rmii_clk_from_mac;
 	bool rmii_rxc;
 };
 
@@ -73,21 +75,33 @@ struct mediatek_dwmac_variant {
 
 /* list of clocks required for mac */
 static const char * const mt2712_dwmac_clk_l[] = {
-	"axi", "apb", "mac_main", "ptp_ref"
+	"axi", "apb", "mac_main", "ptp_ref", "rmii_internal"
 };
 
 static int mt2712_set_interface(struct mediatek_dwmac_plat_data *plat)
 {
+	int rmii_clk_from_mac = plat->rmii_clk_from_mac ? RMII_CLK_SRC_INTERNAL : 0;
 	int rmii_rxc = plat->rmii_rxc ? RMII_CLK_SRC_RXC : 0;
 	u32 intf_val = 0;
 
+	/* The clock labeled as "rmii_internal" in mt2712_dwmac_clk_l is needed
+	 * only in RMII(when MAC provides the reference clock), and useless for
+	 * RGMII/MII/RMII(when PHY provides the reference clock).
+	 * num_clks_to_config indicates the real number of clocks should be
+	 * configured, equals to (plat->variant->num_clks - 1) in default for all the case,
+	 * then +1 for rmii_clk_from_mac case.
+	 */
+	plat->num_clks_to_config = plat->variant->num_clks - 1;
+
 	/* select phy interface in top control domain */
 	switch (plat->phy_mode) {
 	case PHY_INTERFACE_MODE_MII:
 		intf_val |= PHY_INTF_MII;
 		break;
 	case PHY_INTERFACE_MODE_RMII:
-		intf_val |= (PHY_INTF_RMII | rmii_rxc);
+		if (plat->rmii_clk_from_mac)
+			plat->num_clks_to_config++;
+		intf_val |= (PHY_INTF_RMII | rmii_rxc | rmii_clk_from_mac);
 		break;
 	case PHY_INTERFACE_MODE_RGMII:
 	case PHY_INTERFACE_MODE_RGMII_TXID:
@@ -173,35 +187,50 @@ static int mt2712_set_delay(struct mediatek_dwmac_plat_data *plat)
 		delay_val |= FIELD_PREP(ETH_DLY_RXC_INV, mac_delay->rx_inv);
 		break;
 	case PHY_INTERFACE_MODE_RMII:
-		/* the rmii reference clock is from external phy,
-		 * and the property "rmii_rxc" indicates which pin(TXC/RXC)
-		 * the reference clk is connected to. The reference clock is a
-		 * received signal, so rx_delay/rx_inv are used to indicate
-		 * the reference clock timing adjustment
-		 */
-		if (plat->rmii_rxc) {
-			/* the rmii reference clock from outside is connected
-			 * to RXC pin, the reference clock will be adjusted
-			 * by RXC delay macro circuit.
-			 */
-			delay_val |= FIELD_PREP(ETH_DLY_RXC_ENABLE, !!mac_delay->rx_delay);
-			delay_val |= FIELD_PREP(ETH_DLY_RXC_STAGES, mac_delay->rx_delay);
-			delay_val |= FIELD_PREP(ETH_DLY_RXC_INV, mac_delay->rx_inv);
-		} else {
-			/* the rmii reference clock from outside is connected
-			 * to TXC pin, the reference clock will be adjusted
-			 * by TXC delay macro circuit.
+		if (plat->rmii_clk_from_mac) {
+			/* case 1: mac provides the rmii reference clock,
+			 * and the clock output to TXC pin.
+			 * The egress timing can be adjusted by GTXC delay macro circuit.
+			 * The ingress timing can be adjusted by TXC delay macro circuit.
 			 */
 			delay_val |= FIELD_PREP(ETH_DLY_TXC_ENABLE, !!mac_delay->rx_delay);
 			delay_val |= FIELD_PREP(ETH_DLY_TXC_STAGES, mac_delay->rx_delay);
 			delay_val |= FIELD_PREP(ETH_DLY_TXC_INV, mac_delay->rx_inv);
+
+			delay_val |= FIELD_PREP(ETH_DLY_GTXC_ENABLE, !!mac_delay->tx_delay);
+			delay_val |= FIELD_PREP(ETH_DLY_GTXC_STAGES, mac_delay->tx_delay);
+			delay_val |= FIELD_PREP(ETH_DLY_GTXC_INV, mac_delay->tx_inv);
+		} else {
+			/* case 2: the rmii reference clock is from external phy,
+			 * and the property "rmii_rxc" indicates which pin(TXC/RXC)
+			 * the reference clk is connected to. The reference clock is a
+			 * received signal, so rx_delay/rx_inv are used to indicate
+			 * the reference clock timing adjustment
+			 */
+			if (plat->rmii_rxc) {
+				/* the rmii reference clock from outside is connected
+				 * to RXC pin, the reference clock will be adjusted
+				 * by RXC delay macro circuit.
+				 */
+				delay_val |= FIELD_PREP(ETH_DLY_RXC_ENABLE, !!mac_delay->rx_delay);
+				delay_val |= FIELD_PREP(ETH_DLY_RXC_STAGES, mac_delay->rx_delay);
+				delay_val |= FIELD_PREP(ETH_DLY_RXC_INV, mac_delay->rx_inv);
+			} else {
+				/* the rmii reference clock from outside is connected
+				 * to TXC pin, the reference clock will be adjusted
+				 * by TXC delay macro circuit.
+				 */
+				delay_val |= FIELD_PREP(ETH_DLY_TXC_ENABLE, !!mac_delay->rx_delay);
+				delay_val |= FIELD_PREP(ETH_DLY_TXC_STAGES, mac_delay->rx_delay);
+				delay_val |= FIELD_PREP(ETH_DLY_TXC_INV, mac_delay->rx_inv);
+			}
+			/* tx_inv will inverse the tx clock inside mac relateive to
+			 * reference clock from external phy,
+			 * and this bit is located in the same register with fine-tune
+			 */
+			if (mac_delay->tx_inv)
+				fine_val = ETH_RMII_DLY_TX_INV;
 		}
-		/* tx_inv will inverse the tx clock inside mac relateive to
-		 * reference clock from external phy,
-		 * and this bit is located in the same register with fine-tune
-		 */
-		if (mac_delay->tx_inv)
-			fine_val = ETH_RMII_DLY_TX_INV;
 		break;
 	case PHY_INTERFACE_MODE_RGMII:
 	case PHY_INTERFACE_MODE_RGMII_TXID:
@@ -278,6 +307,7 @@ static int mediatek_dwmac_config_dt(struct mediatek_dwmac_plat_data *plat)
 	mac_delay->tx_inv = of_property_read_bool(plat->np, "mediatek,txc-inverse");
 	mac_delay->rx_inv = of_property_read_bool(plat->np, "mediatek,rxc-inverse");
 	plat->rmii_rxc = of_property_read_bool(plat->np, "mediatek,rmii-rxc");
+	plat->rmii_clk_from_mac = of_property_read_bool(plat->np, "mediatek,rmii-clk-from-mac");
 
 	return 0;
 }
@@ -294,6 +324,8 @@ static int mediatek_dwmac_clk_init(struct mediatek_dwmac_plat_data *plat)
 	for (i = 0; i < num; i++)
 		plat->clks[i].id = variant->clk_list[i];
 
+	plat->num_clks_to_config = variant->num_clks;
+
 	return devm_clk_bulk_get(plat->dev, num, plat->clks);
 }
 
@@ -321,7 +353,7 @@ static int mediatek_dwmac_init(struct platform_device *pdev, void *priv)
 		return ret;
 	}
 
-	ret = clk_bulk_prepare_enable(variant->num_clks, plat->clks);
+	ret = clk_bulk_prepare_enable(plat->num_clks_to_config, plat->clks);
 	if (ret) {
 		dev_err(plat->dev, "failed to enable clks, err = %d\n", ret);
 		return ret;
@@ -336,9 +368,8 @@ static int mediatek_dwmac_init(struct platform_device *pdev, void *priv)
 static void mediatek_dwmac_exit(struct platform_device *pdev, void *priv)
 {
 	struct mediatek_dwmac_plat_data *plat = priv;
-	const struct mediatek_dwmac_variant *variant = plat->variant;
 
-	clk_bulk_disable_unprepare(variant->num_clks, plat->clks);
+	clk_bulk_disable_unprepare(plat->num_clks_to_config, plat->clks);
 
 	pm_runtime_put_sync(&pdev->dev);
 	pm_runtime_disable(&pdev->dev);
-- 
2.18.0

  reply	other threads:[~2019-12-16  5:40 UTC|newest]

Thread overview: 4+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-12-16  5:39 [v2, PATCH 0/2] net-next: stmmac: dwmac-mediatek: " Biao Huang
2019-12-16  5:39 ` Biao Huang [this message]
2019-12-16  5:39 ` [v2, PATCH 2/2] net-next: dt-binding: dwmac-mediatek: add more description " Biao Huang
2019-12-17 21:48 ` [v2, PATCH 0/2] net-next: stmmac: dwmac-mediatek: add more support " David Miller

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20191216053958.26130-2-biao.huang@mediatek.com \
    --to=biao.huang@mediatek.com \
    --cc=alexandre.torgue@st.com \
    --cc=andrew@lunn.ch \
    --cc=davem@davemloft.net \
    --cc=devicetree@vger.kernel.org \
    --cc=joabreu@synopsys.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mediatek@lists.infradead.org \
    --cc=linux-stm32@st-md-mailman.stormreply.com \
    --cc=mark.rutland@arm.com \
    --cc=matthias.bgg@gmail.com \
    --cc=mcoquelin.stm32@gmail.com \
    --cc=netdev@vger.kernel.org \
    --cc=peppe.cavallaro@st.com \
    --cc=robh+dt@kernel.org \
    --cc=yt.shen@mediatek.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®