Re: [RESEND PATCH v10 02/10] vmx: spp: Add control flags for Sub-Page Protection(SPP)

[Yang Weijiang <weijiang.yang@intel.com>]

On Fri, Jan 10, 2020 at 08:58:59AM -0800, Sean Christopherson wrote:
> On Thu, Jan 02, 2020 at 02:13:11PM +0800, Yang Weijiang wrote:
> > diff --git a/arch/x86/kvm/vmx/vmx.c b/arch/x86/kvm/vmx/vmx.c
> > index e3394c839dea..5713e8a6224c 100644
> > --- a/arch/x86/kvm/vmx/vmx.c
> > +++ b/arch/x86/kvm/vmx/vmx.c
> > @@ -60,6 +60,7 @@
> >  #include "vmcs12.h"
> >  #include "vmx.h"
> >  #include "x86.h"
> > +#include "../mmu/spp.h"
> 
> The ".." should be unnecessary, e.g. x86.h is obviously a level up.
>
Sean, thanks a lot for the feedback! Will change this.
> >  MODULE_AUTHOR("Qumranet");
> >  MODULE_LICENSE("GPL");
> > @@ -111,6 +112,7 @@ module_param_named(pml, enable_pml, bool, S_IRUGO);
> >  
> >  static bool __read_mostly dump_invalid_vmcs = 0;
> >  module_param(dump_invalid_vmcs, bool, 0644);
> > +static bool __read_mostly spp_supported = 0;
> 
> s/spp_supported/enable_spp to be consistent with all the other booleans.
> 
> Is there a reason this isn't exposed as a module param?
> 
Yes, in original versions, SPP is enbled by a module param, so called
"static enable", considering the SPP bitmap pre-allocated is a bit
large, the from v3, it's changed to "dynamic enable", i.e., user
application need to enable SPP via init_spp IOCTL(later changed to via
ENABLE_CAP) to remove the pre-allocation, so the flag now is used to
cross-check SPP status between functions. Will change the name.

> And if this is to be on by default, then the flag itself should be
> initialized to '1' so that it's clear to readers that the feature is
> enabled by default (if it's supported).  Looking at only this code, I would
> think that SPP is forced off and can't be enabled.
> 
> That being said, turning on the enable_spp control flag should be the last
> patch in the series, i.e. it shouldn't be turned on until all the
> underlying support code is in place.  So, I would keep this as is, but
> invert the code in hardware_setup() below.  That way the flag exists and
> is checked, but can't be turned on without modifying the code.  Then when
> all is said and done, you can add a patch to introduce the module param
> and turn on the flag by default (if that's indeed what we want).
> 
You're right, I'll re-order the patch to enable SPP bit in the last
patch, thanks!

> >  #define MSR_BITMAP_MODE_X2APIC		1
> >  #define MSR_BITMAP_MODE_X2APIC_APICV	2
> > @@ -2391,6 +2393,7 @@ static __init int setup_vmcs_config(struct vmcs_config *vmcs_conf,
> >  			SECONDARY_EXEC_RDSEED_EXITING |
> >  			SECONDARY_EXEC_RDRAND_EXITING |
> >  			SECONDARY_EXEC_ENABLE_PML |
> > +			SECONDARY_EXEC_ENABLE_SPP |
> >  			SECONDARY_EXEC_TSC_SCALING |
> >  			SECONDARY_EXEC_ENABLE_USR_WAIT_PAUSE |
> >  			SECONDARY_EXEC_PT_USE_GPA |
> > @@ -4039,6 +4042,9 @@ static void vmx_compute_secondary_exec_control(struct vcpu_vmx *vmx)
> >  	if (!enable_pml)
> >  		exec_control &= ~SECONDARY_EXEC_ENABLE_PML;
> >  
> > +	if (!spp_supported)
> > +		exec_control &= ~SECONDARY_EXEC_ENABLE_SPP;
> > +
> >  	if (vmx_xsaves_supported()) {
> >  		/* Exposing XSAVES only when XSAVE is exposed */
> >  		bool xsaves_enabled =
> > @@ -7630,6 +7636,9 @@ static __init int hardware_setup(void)
> >  	if (!cpu_has_vmx_flexpriority())
> >  		flexpriority_enabled = 0;
> >  
> > +	if (cpu_has_vmx_ept_spp() && enable_ept)
> > +		spp_supported = 1;
> 
> As above, invert this to disable spp when it's not supported, or when EPT
> is disabled (or not supported).
>
Sure,thank you!
> > +
> >  	if (!cpu_has_virtual_nmis())
> >  		enable_vnmi = 0;
> >  
> > -- 
> > 2.17.2
> >