From: Voon Weifeng <weifeng.voon@intel.com>
To: "David S . Miller" <davem@davemloft.net>,
Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: netdev@vger.kernel.org, linux-kernel@vger.kernel.org,
Jose Abreu <joabreu@synopsys.com>,
Giuseppe Cavallaro <peppe.cavallaro@st.com>,
Andrew Lunn <andrew@lunn.ch>,
Alexandre Torgue <alexandre.torgue@st.com>,
Ong Boon Leong <boon.leong.ong@intel.com>,
Voon Weifeng <weifeng.voon@intel.com>,
Seow Chen Yong <chen.yong.seow@intel.com>,
Mark Gross <mgross@linux.intel.com>,
Wong Vee Khee <vee.khee.wong@intel.com>
Subject: [PATCH v2 net] net: stmmac: Modify configuration method of EEE timers
Date: Thu, 1 Oct 2020 23:56:09 +0800 [thread overview]
Message-ID: <20201001155609.5372-1-weifeng.voon@intel.com> (raw)
From: "Vineetha G. Jaya Kumaran" <vineetha.g.jaya.kumaran@intel.com>
Ethtool manual stated that the tx-timer is the "the amount of time the
device should stay in idle mode prior to asserting its Tx LPI". The
previous implementation for "ethtool --set-eee tx-timer" sets the LPI TW
timer duration which is not correct. Hence, this patch fixes the
"ethtool --set-eee tx-timer" to configure the EEE LPI timer.
The LPI TW Timer will be using the defined default value instead of
"ethtool --set-eee tx-timer" which follows the EEE LS timer implementation.
Fixes: d765955d2ae0 ("stmmac: add the Energy Efficient Ethernet support")
Signed-off-by: Vineetha G. Jaya Kumaran <vineetha.g.jaya.kumaran@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Changelog V2
*Not removing/modifying the eee_timer.
*EEE LPI timer can be configured through ethtool and also the eee_timer
module param.
*EEE TW Timer will be configured with default value only, not able to be
configured through ethtool or module param. This follows the implementation
of the EEE LS Timer.
---
drivers/net/ethernet/stmicro/stmmac/stmmac.h | 2 ++
.../ethernet/stmicro/stmmac/stmmac_ethtool.c | 12 +++++++++-
.../net/ethernet/stmicro/stmmac/stmmac_main.c | 23 ++++++++++++-------
3 files changed, 28 insertions(+), 9 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac.h b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
index 9c02fc754bf1..545696971f65 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac.h
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
@@ -203,6 +203,8 @@ struct stmmac_priv {
int eee_enabled;
int eee_active;
int tx_lpi_timer;
+ int tx_lpi_enabled;
+ int eee_tw_timer;
unsigned int mode;
unsigned int chain_mode;
int extend_desc;
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
index 430a4b32ec1e..814879f91f76 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
@@ -665,6 +665,7 @@ static int stmmac_ethtool_op_get_eee(struct net_device *dev,
edata->eee_enabled = priv->eee_enabled;
edata->eee_active = priv->eee_active;
edata->tx_lpi_timer = priv->tx_lpi_timer;
+ edata->tx_lpi_enabled = priv->tx_lpi_enabled;
return phylink_ethtool_get_eee(priv->phylink, edata);
}
@@ -678,6 +679,10 @@ static int stmmac_ethtool_op_set_eee(struct net_device *dev,
if (!priv->dma_cap.eee)
return -EOPNOTSUPP;
+ if (priv->tx_lpi_enabled != edata->tx_lpi_enabled)
+ netdev_warn(priv->dev,
+ "Setting EEE tx-lpi is not supported\n");
+
if (!edata->eee_enabled)
stmmac_disable_eee_mode(priv);
@@ -685,7 +690,12 @@ static int stmmac_ethtool_op_set_eee(struct net_device *dev,
if (ret)
return ret;
- priv->tx_lpi_timer = edata->tx_lpi_timer;
+ if (edata->eee_enabled &&
+ priv->tx_lpi_timer != edata->tx_lpi_timer) {
+ priv->tx_lpi_timer = edata->tx_lpi_timer;
+ stmmac_eee_init(priv);
+ }
+
return 0;
}
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index 89b2b3472852..b56b13d64ab4 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -94,7 +94,7 @@ static const u32 default_msg_level = (NETIF_MSG_DRV | NETIF_MSG_PROBE |
static int eee_timer = STMMAC_DEFAULT_LPI_TIMER;
module_param(eee_timer, int, 0644);
MODULE_PARM_DESC(eee_timer, "LPI tx expiration time in msec");
-#define STMMAC_LPI_T(x) (jiffies + msecs_to_jiffies(x))
+#define STMMAC_LPI_T(x) (jiffies + usecs_to_jiffies(x))
/* By default the driver will use the ring mode to manage tx and rx descriptors,
* but allow user to force to use the chain instead of the ring
@@ -370,7 +370,7 @@ static void stmmac_eee_ctrl_timer(struct timer_list *t)
struct stmmac_priv *priv = from_timer(priv, t, eee_ctrl_timer);
stmmac_enable_eee_mode(priv);
- mod_timer(&priv->eee_ctrl_timer, STMMAC_LPI_T(eee_timer));
+ mod_timer(&priv->eee_ctrl_timer, STMMAC_LPI_T(priv->tx_lpi_timer));
}
/**
@@ -383,7 +383,7 @@ static void stmmac_eee_ctrl_timer(struct timer_list *t)
*/
bool stmmac_eee_init(struct stmmac_priv *priv)
{
- int tx_lpi_timer = priv->tx_lpi_timer;
+ int eee_tw_timer = priv->eee_tw_timer;
/* Using PCS we cannot dial with the phy registers at this stage
* so we do not support extra feature like EEE.
@@ -403,7 +403,7 @@ bool stmmac_eee_init(struct stmmac_priv *priv)
if (priv->eee_enabled) {
netdev_dbg(priv->dev, "disable EEE\n");
del_timer_sync(&priv->eee_ctrl_timer);
- stmmac_set_eee_timer(priv, priv->hw, 0, tx_lpi_timer);
+ stmmac_set_eee_timer(priv, priv->hw, 0, eee_tw_timer);
}
mutex_unlock(&priv->lock);
return false;
@@ -411,11 +411,12 @@ bool stmmac_eee_init(struct stmmac_priv *priv)
if (priv->eee_active && !priv->eee_enabled) {
timer_setup(&priv->eee_ctrl_timer, stmmac_eee_ctrl_timer, 0);
- mod_timer(&priv->eee_ctrl_timer, STMMAC_LPI_T(eee_timer));
stmmac_set_eee_timer(priv, priv->hw, STMMAC_DEFAULT_LIT_LS,
- tx_lpi_timer);
+ eee_tw_timer);
}
+ mod_timer(&priv->eee_ctrl_timer, STMMAC_LPI_T(priv->tx_lpi_timer));
+
mutex_unlock(&priv->lock);
netdev_dbg(priv->dev, "Energy-Efficient Ethernet initialized\n");
return true;
@@ -930,6 +931,7 @@ static void stmmac_mac_link_down(struct phylink_config *config,
stmmac_mac_set(priv, priv->ioaddr, false);
priv->eee_active = false;
+ priv->tx_lpi_enabled = false;
stmmac_eee_init(priv);
stmmac_set_eee_pls(priv, priv->hw, false);
}
@@ -1027,6 +1029,7 @@ static void stmmac_mac_link_up(struct phylink_config *config,
if (phy && priv->dma_cap.eee) {
priv->eee_active = phy_init_eee(phy, 1) >= 0;
priv->eee_enabled = stmmac_eee_init(priv);
+ priv->tx_lpi_enabled = priv->eee_enabled;
stmmac_set_eee_pls(priv, priv->hw, true);
}
}
@@ -2061,7 +2064,7 @@ static int stmmac_tx_clean(struct stmmac_priv *priv, int budget, u32 queue)
if ((priv->eee_enabled) && (!priv->tx_path_in_lpi_mode)) {
stmmac_enable_eee_mode(priv);
- mod_timer(&priv->eee_ctrl_timer, STMMAC_LPI_T(eee_timer));
+ mod_timer(&priv->eee_ctrl_timer, STMMAC_LPI_T(priv->tx_lpi_timer));
}
/* We still have pending packets, let's call for a new scheduling */
@@ -2694,7 +2697,11 @@ static int stmmac_hw_setup(struct net_device *dev, bool init_ptp)
netdev_warn(priv->dev, "PTP init failed\n");
}
- priv->tx_lpi_timer = STMMAC_DEFAULT_TWT_LS;
+ priv->eee_tw_timer = STMMAC_DEFAULT_TWT_LS;
+
+ /* Convert the timer from msec to usec */
+ if (!priv->tx_lpi_timer)
+ priv->tx_lpi_timer = eee_timer * 1000;
if (priv->use_riwt) {
if (!priv->rx_riwt)
--
2.17.1
next reply other threads:[~2020-10-01 15:56 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-10-01 15:56 Voon Weifeng [this message]
2020-10-03 23:42 ` David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20201001155609.5372-1-weifeng.voon@intel.com \
--to=weifeng.voon@intel.com \
--cc=alexandre.torgue@st.com \
--cc=andrew@lunn.ch \
--cc=boon.leong.ong@intel.com \
--cc=chen.yong.seow@intel.com \
--cc=davem@davemloft.net \
--cc=joabreu@synopsys.com \
--cc=linux-kernel@vger.kernel.org \
--cc=mcoquelin.stm32@gmail.com \
--cc=mgross@linux.intel.com \
--cc=netdev@vger.kernel.org \
--cc=peppe.cavallaro@st.com \
--cc=vee.khee.wong@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®