From: Wenbin Mei <wenbin.mei@mediatek.com>
To: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Chaotian Jing <chaotian.jing@mediatek.com>,
Matthias Brugger <matthias.bgg@gmail.com>,
<linux-mmc@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-mediatek@lists.infradead.org>,
<linux-kernel@vger.kernel.org>, <srv_heupstream@mediatek.com>,
Wenbin Mei <wenbin.mei@mediatek.com>
Subject: [PATCH v1 1/1] mmc: mediatek: add HS400 enhanced strobe support
Date: Mon, 2 Nov 2020 17:28:22 +0800 [thread overview]
Message-ID: <20201102092822.5301-2-wenbin.mei@mediatek.com> (raw)
In-Reply-To: <20201102092822.5301-1-wenbin.mei@mediatek.com>
Add support for HS400ES mode to MediaTek MMC Card Driver.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
---
drivers/mmc/host/mtk-sd.c | 40 +++++++++++++++++++++++++++++++++++++++
1 file changed, 40 insertions(+)
diff --git a/drivers/mmc/host/mtk-sd.c b/drivers/mmc/host/mtk-sd.c
index f7f68623fefc..fc5ee5df91ad 100644
--- a/drivers/mmc/host/mtk-sd.c
+++ b/drivers/mmc/host/mtk-sd.c
@@ -78,9 +78,12 @@
#define MSDC_PAD_TUNE0 0xf0
#define PAD_DS_TUNE 0x188
#define PAD_CMD_TUNE 0x18c
+#define EMMC51_CFG0 0x204
#define EMMC50_CFG0 0x208
+#define EMMC50_CFG1 0x20c
#define EMMC50_CFG3 0x220
#define SDC_FIFO_CFG 0x228
+#define CQHCI_SETTING 0x7fc
/*--------------------------------------------------------------------------*/
/* Top Pad Register Offset */
@@ -261,15 +264,26 @@
#define PAD_CMD_TUNE_RX_DLY3 (0x1f << 1) /* RW */
+/* EMMC51_CFG0 mask */
+#define CMDQ_RDAT_CNT (0x3ff << 12) /* RW */
+
#define EMMC50_CFG_PADCMD_LATCHCK (0x1 << 0) /* RW */
#define EMMC50_CFG_CRCSTS_EDGE (0x1 << 3) /* RW */
#define EMMC50_CFG_CFCSTS_SEL (0x1 << 4) /* RW */
+#define EMMC50_CFG_CMD_RESP_SEL (0x1 << 9) /* RW */
+
+/* EMMC50_CFG1 mask */
+#define EMMC50_CFG1_DS_CFG (0x1 << 28) /* RW */
#define EMMC50_CFG3_OUTS_WR (0x1f << 0) /* RW */
#define SDC_FIFO_CFG_WRVALIDSEL (0x1 << 24) /* RW */
#define SDC_FIFO_CFG_RDVALIDSEL (0x1 << 25) /* RW */
+/* CQHCI_SETTING */
+#define CQHCI_RD_CMD_WND_SEL (0x1 << 14) /* RW */
+#define CQHCI_WR_CMD_WND_SEL (0x1 << 15) /* RW */
+
/* EMMC_TOP_CONTROL mask */
#define PAD_RXDLY_SEL (0x1 << 0) /* RW */
#define DELAY_EN (0x1 << 1) /* RW */
@@ -2276,6 +2290,31 @@ static int msdc_get_cd(struct mmc_host *mmc)
return !val;
}
+static void msdc_hs400_enhanced_strobe(struct mmc_host *mmc,
+ struct mmc_ios *ios)
+{
+ struct msdc_host *host = mmc_priv(mmc);
+
+ if (ios->enhanced_strobe) {
+ msdc_prepare_hs400_tuning(mmc, ios);
+ sdr_set_field(host->base + EMMC50_CFG0, EMMC50_CFG_PADCMD_LATCHCK, 1);
+ sdr_set_field(host->base + EMMC50_CFG0, EMMC50_CFG_CMD_RESP_SEL, 1);
+ sdr_set_field(host->base + EMMC50_CFG1, EMMC50_CFG1_DS_CFG, 1);
+
+ sdr_clr_bits(host->base + CQHCI_SETTING, CQHCI_RD_CMD_WND_SEL);
+ sdr_clr_bits(host->base + CQHCI_SETTING, CQHCI_WR_CMD_WND_SEL);
+ sdr_clr_bits(host->base + EMMC51_CFG0, CMDQ_RDAT_CNT);
+ } else {
+ sdr_set_field(host->base + EMMC50_CFG0, EMMC50_CFG_PADCMD_LATCHCK, 0);
+ sdr_set_field(host->base + EMMC50_CFG0, EMMC50_CFG_CMD_RESP_SEL, 0);
+ sdr_set_field(host->base + EMMC50_CFG1, EMMC50_CFG1_DS_CFG, 0);
+
+ sdr_set_bits(host->base + CQHCI_SETTING, CQHCI_RD_CMD_WND_SEL);
+ sdr_set_bits(host->base + CQHCI_SETTING, CQHCI_WR_CMD_WND_SEL);
+ sdr_set_field(host->base + EMMC51_CFG0, CMDQ_RDAT_CNT, 0xb4);
+ }
+}
+
static void msdc_cqe_enable(struct mmc_host *mmc)
{
struct msdc_host *host = mmc_priv(mmc);
@@ -2333,6 +2372,7 @@ static const struct mmc_host_ops mt_msdc_ops = {
.set_ios = msdc_ops_set_ios,
.get_ro = mmc_gpio_get_ro,
.get_cd = msdc_get_cd,
+ .hs400_enhanced_strobe = msdc_hs400_enhanced_strobe,
.enable_sdio_irq = msdc_enable_sdio_irq,
.ack_sdio_irq = msdc_ack_sdio_irq,
.start_signal_voltage_switch = msdc_ops_switch_volt,
--
2.18.0
next prev parent reply other threads:[~2020-11-02 9:29 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-11-02 9:28 [PATCH v1 0/1] Add " Wenbin Mei
2020-11-02 9:28 ` Wenbin Mei [this message]
2020-11-05 12:59 ` [PATCH v1 1/1] mmc: mediatek: add " Ulf Hansson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20201102092822.5301-2-wenbin.mei@mediatek.com \
--to=wenbin.mei@mediatek.com \
--cc=chaotian.jing@mediatek.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=linux-mmc@vger.kernel.org \
--cc=matthias.bgg@gmail.com \
--cc=srv_heupstream@mediatek.com \
--cc=ulf.hansson@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®