From: Jacopo Mondi <jacopo@jmondi.org>
To: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Prabhakar <prabhakar.csengg@gmail.com>,
Magnus Damm <magnus.damm@gmail.com>,
Rob Herring <robh+dt@kernel.org>,
Biju Das <biju.das.jz@bp.renesas.com>,
linux-renesas-soc@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Subject: Re: [PATCH v4 1/2] ARM: dts: r8a7742-iwg21d-q7-dbcm-ca: Separate out ov5640 nodes
Date: Tue, 15 Dec 2020 18:22:11 +0100 [thread overview]
Message-ID: <20201215172211.srhbkulj653eweu2@uno.localdomain> (raw)
In-Reply-To: <20201126134031.4115211-2-geert@linux-m68k.org>
Hi Geert,
On Thu, Nov 26, 2020 at 02:40:30PM +0100, Geert Uytterhoeven wrote:
> From: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
>
> The camera daughter board can also be connected to 8-bit ov7725 sensors,
> so in preparation for configurable option to choose depending on the
> camera's connected separate out the ov5640 nodes in a dtsi file.
>
> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
> [geert: describe a single camera in the .dtsi, include multiple times]
> Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
> ---
> v4:
> - Describe a single camera in the .dtsi file,
> - Include the .dtsi multiple times,
>
> .../boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts | 151 +++++++++---------
> .../r8a7742-iwg21d-q7-dbcm-ov5640-single.dtsi | 30 ++++
> 2 files changed, 103 insertions(+), 78 deletions(-)
> create mode 100644 arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ov5640-single.dtsi
>
> diff --git a/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts
> index 98c3fbd89fa6c5c7..00634eb58ce39da5 100644
> --- a/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts
> +++ b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts
> @@ -91,67 +91,12 @@ &hscif0 {
> status = "okay";
> };
>
> -&i2c0 {
> - ov5640@3c {
> - compatible = "ovti,ov5640";
> - reg = <0x3c>;
> - clocks = <&mclk_cam1>;
> - clock-names = "xclk";
> -
> - port {
> - ov5640_0: endpoint {
> - bus-width = <8>;
> - data-shift = <2>;
> - bus-type = <6>;
> - pclk-sample = <1>;
> - remote-endpoint = <&vin0ep>;
> - };
> - };
> - };
> -};
> -
> &i2c1 {
> pinctrl-0 = <&i2c1_pins>;
> pinctrl-names = "default";
>
> status = "okay";
> clock-frequency = <400000>;
i2c1 and i2c3 are here unconditionally enabled, while i2c0 and i2c2
seem to be already enabled and configured already in the included
.dtsi
Wouldn't it be more approriate to enable and configure i2c1 and i2c3
in the r8a7742-iwg21d-q7-dbcm-ov5640-single.dtsi only if a camera
is there connected ?
> -
> - ov5640@3c {
> - compatible = "ovti,ov5640";
> - reg = <0x3c>;
> - clocks = <&mclk_cam2>;
> - clock-names = "xclk";
> -
> - port {
> - ov5640_1: endpoint {
> - bus-width = <8>;
> - data-shift = <2>;
> - bus-type = <6>;
> - pclk-sample = <1>;
> - remote-endpoint = <&vin1ep>;
> - };
> - };
> - };
> -};
> -
> -&i2c2 {
> - ov5640@3c {
> - compatible = "ovti,ov5640";
> - reg = <0x3c>;
> - clocks = <&mclk_cam3>;
> - clock-names = "xclk";
> -
> - port {
> - ov5640_2: endpoint {
> - bus-width = <8>;
> - data-shift = <2>;
> - bus-type = <6>;
> - pclk-sample = <1>;
> - remote-endpoint = <&vin2ep>;
> - };
> - };
> - };
> };
>
> &i2c3 {
> @@ -160,23 +105,6 @@ &i2c3 {
>
> status = "okay";
> clock-frequency = <400000>;
> -
> - ov5640@3c {
> - compatible = "ovti,ov5640";
> - reg = <0x3c>;
> - clocks = <&mclk_cam4>;
> - clock-names = "xclk";
> -
> - port {
> - ov5640_3: endpoint {
> - bus-width = <8>;
> - data-shift = <2>;
> - bus-type = <6>;
> - pclk-sample = <1>;
> - remote-endpoint = <&vin3ep>;
> - };
> - };
> - };
> };
>
> &pfc {
> @@ -267,6 +195,21 @@ &scifb1 {
> cts-gpios = <&gpio4 17 GPIO_ACTIVE_LOW>;
> };
>
> +/*
> + * Below configuration ties VINx endpoints to ov5640/ov7725 camera endpoints
> + *
> + * Uncomment the #include statements to change configuration
> + */
> +
> +/* 8bit CMOS Camera 1 (J13) */
> +#define CAM_PARENT_I2C i2c0
> +#define MCLK_CAM mclk_cam1
> +#define CAM_EP cam0ep
> +#define VIN_EP vin0ep
> +#undef CAM_ENABLED
> +#include "r8a7742-iwg21d-q7-dbcm-ov5640-single.dtsi"
> +
> +#ifdef CAM_ENABLED
> &vin0 {
> /*
> * Set SW2 switch on the SOM to 'ON'
> @@ -278,13 +221,28 @@ &vin0 {
>
> port {
> vin0ep: endpoint {
> - remote-endpoint = <&ov5640_0>;
> + remote-endpoint = <&cam0ep>;
> bus-width = <8>;
> bus-type = <6>;
> };
> };
> };
> -
> +#endif /* CAM_ENABLED */
> +
> +#undef CAM_PARENT_I2C
> +#undef MCLK_CAM
> +#undef CAM_EP
> +#undef VIN_EP
> +
> +/* 8bit CMOS Camera 2 (J14) */
> +#define CAM_PARENT_I2C i2c1
> +#define MCLK_CAM mclk_cam2
> +#define CAM_EP cam1ep
> +#define VIN_EP vin1ep
> +#undef CAM_ENABLED
> +#include "r8a7742-iwg21d-q7-dbcm-ov5640-single.dtsi"
> +
> +#ifdef CAM_ENABLED
> &vin1 {
> /* Set SW1 switch on the SOM to 'ON' */
> status = "okay";
> @@ -293,13 +251,29 @@ &vin1 {
>
> port {
> vin1ep: endpoint {
> - remote-endpoint = <&ov5640_1>;
> + remote-endpoint = <&cam1ep>;
> bus-width = <8>;
> bus-type = <6>;
> };
> };
> };
>
> +#endif /* CAM_ENABLED */
> +
> +#undef CAM_PARENT_I2C
> +#undef MCLK_CAM
> +#undef CAM_EP
> +#undef VIN_EP
> +
> +/* 8bit CMOS Camera 3 (J12) */
> +#define CAM_PARENT_I2C i2c2
> +#define MCLK_CAM mclk_cam3
> +#define CAM_EP cam2ep
> +#define VIN_EP vin2ep
> +#undef CAM_ENABLED
> +#include "r8a7742-iwg21d-q7-dbcm-ov5640-single.dtsi"
> +
> +#ifdef CAM_ENABLED
> &vin2 {
> status = "okay";
> pinctrl-0 = <&vin2_pins>;
> @@ -307,14 +281,29 @@ &vin2 {
>
> port {
> vin2ep: endpoint {
> - remote-endpoint = <&ov5640_2>;
> + remote-endpoint = <&cam2ep>;
> bus-width = <8>;
> data-shift = <8>;
> bus-type = <6>;
> };
> };
> };
> -
> +#endif /* CAM_ENABLED */
> +
> +#undef CAM_PARENT_I2C
> +#undef MCLK_CAM
> +#undef CAM_EP
> +#undef VIN_EP
> +
> +/* 8bit CMOS Camera 4 (J11) */
> +#define CAM_PARENT_I2C i2c3
> +#define MCLK_CAM mclk_cam4
> +#define CAM_EP cam3ep
> +#define VIN_EP vin3ep
> +#undef CAM_ENABLED
> +#include "r8a7742-iwg21d-q7-dbcm-ov5640-single.dtsi"
> +
> +#ifdef CAM_ENABLED
> &vin3 {
> status = "okay";
> pinctrl-0 = <&vin3_pins>;
> @@ -322,9 +311,15 @@ &vin3 {
>
> port {
> vin3ep: endpoint {
> - remote-endpoint = <&ov5640_3>;
> + remote-endpoint = <&cam3ep>;
> bus-width = <8>;
> bus-type = <6>;
> };
> };
> };
> +#endif /* CAM_ENABLED */
> +
> +#undef CAM_PARENT_I2C
> +#undef MCLK_CAM
> +#undef CAM_EP
> +#undef VIN_EP
> diff --git a/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ov5640-single.dtsi b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ov5640-single.dtsi
> new file mode 100644
> index 0000000000000000..408016620f5b1a04
> --- /dev/null
> +++ b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ov5640-single.dtsi
> @@ -0,0 +1,30 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * This include file ties a VIN interface with a single ov5640 sensor on
> + * the iWave-RZ/G1H Qseven board development platform connected with the
> + * camera daughter board.
> + *
> + * Copyright (C) 2020 Renesas Electronics Corp.
> + */
> +
> +#define CAM_ENABLED 1
> +
> +&CAM_PARENT_I2C {
> + ov5640@3c {
> + compatible = "ovti,ov5640";
> + reg = <0x3c>;
> + clocks = <&MCLK_CAM>;
> + clock-names = "xclk";
> + status = "okay";
> +
> + port {
> + CAM_EP: endpoint {
> + bus-width = <8>;
> + data-shift = <2>;
> + bus-type = <6>;
> + pclk-sample = <1>;
> + remote-endpoint = <&VIN_EP>;
> + };
> + };
> + };
> +};
> --
> 2.25.1
>
next prev parent reply other threads:[~2020-12-15 17:23 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-11-26 13:40 [PATCH v4 0/2] ARM: dts: r8a7742-iwg21d-q7-dbcm: Add support for ov7725 sensors Geert Uytterhoeven
2020-11-26 13:40 ` [PATCH v4 1/2] ARM: dts: r8a7742-iwg21d-q7-dbcm-ca: Separate out ov5640 nodes Geert Uytterhoeven
2020-11-26 17:42 ` Prabhakar Mahadev Lad
2020-11-30 9:15 ` Geert Uytterhoeven
2020-12-15 17:22 ` Jacopo Mondi [this message]
2020-11-26 13:40 ` [PATCH v4 2/2] ARM: dts: r8a7742-iwg21d-q7-dbcm-ca: Add support for 8-bit ov7725 sensors Geert Uytterhoeven
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20201215172211.srhbkulj653eweu2@uno.localdomain \
--to=jacopo@jmondi.org \
--cc=biju.das.jz@bp.renesas.com \
--cc=devicetree@vger.kernel.org \
--cc=geert@linux-m68k.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-renesas-soc@vger.kernel.org \
--cc=magnus.damm@gmail.com \
--cc=prabhakar.csengg@gmail.com \
--cc=prabhakar.mahadev-lad.rj@bp.renesas.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®