From: Andrew Lunn <andrew@lunn.ch>
To: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Steen Hegelund <steen.hegelund@microchip.com>,
"David S. Miller" <davem@davemloft.net>,
Jakub Kicinski <kuba@kernel.org>,
Russell King <linux@armlinux.org.uk>,
Lars Povlsen <lars.povlsen@microchip.com>,
Bjarni Jonasson <bjarni.jonasson@microchip.com>,
Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>,
Madalin Bucur <madalin.bucur@oss.nxp.com>,
Nicolas Ferre <nicolas.ferre@microchip.com>,
Mark Einon <mark.einon@gmail.com>,
Masahiro Yamada <masahiroy@kernel.org>,
Arnd Bergmann <arnd@arndb.de>,
netdev@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org
Subject: Re: [RFC PATCH v2 3/8] net: sparx5: add hostmode with phylink support
Date: Wed, 23 Dec 2020 22:05:21 +0100 [thread overview]
Message-ID: <20201223210521.GB3253993@lunn.ch> (raw)
In-Reply-To: <20201223205852.GA4138276@piout.net>
On Wed, Dec 23, 2020 at 09:58:52PM +0100, Alexandre Belloni wrote:
> On 22/12/2020 15:41:41+0100, Andrew Lunn wrote:
> > > Yes the register based injection/extration is not going to be fast, but
> > > the FDMA and its driver is being sent later as separate series to keep
> > > the size of this review down.
> >
> > FDMA?
> >
> > I need a bit more background here, just to make use this should be a
> > pure switchdev driver and not a DSA driver.
> >
>
> I don't think this should be a DSA driver. As for Ocelot, the CPU
> port is not a MAC and in that use case, this would be like a top of the
> rack switch with traffic going to the CPU port being mostly used for
> managmement (dhcp, stp, etc...) as opposed to being used to forward
> traffic to another interface, like WAN or wifi.
>
> However, I would think there will be cases where the internal CPU is not
> use and instead use ths switch in a DSA setting, very much like what is
> done for Felix with regards to Ocelot.
From what i have heard so far, it does seem like a pure switchdev
driver is correct. So long as FDMA is not a standalone Ethernet
driver, but just a DMA engine incorporated into this driver, the
architecture looks correct.
I was asking because from the information that was available, it was
impossible to say what the correct architecture should be.
Andrew
next prev parent reply other threads:[~2020-12-23 21:06 UTC|newest]
Thread overview: 38+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-12-17 7:51 [RFC PATCH v2 0/8] Adding the Sparx5 Switch Driver Steen Hegelund
2020-12-17 7:51 ` [RFC PATCH v2 1/8] dt-bindings: net: sparx5: Add sparx5-switch bindings Steen Hegelund
2020-12-19 17:54 ` Andrew Lunn
2020-12-21 0:55 ` Florian Fainelli
2020-12-21 10:00 ` Steen Hegelund
2020-12-21 21:40 ` Rob Herring
2020-12-22 7:30 ` Steen Hegelund
2020-12-17 7:51 ` [RFC PATCH v2 2/8] net: sparx5: add the basic sparx5 driver Steen Hegelund
2020-12-19 19:11 ` Andrew Lunn
2020-12-22 13:50 ` Steen Hegelund
2020-12-22 15:01 ` Andrew Lunn
2020-12-22 16:56 ` Alexandre Belloni
2020-12-23 9:03 ` Lars Povlsen
2020-12-23 8:52 ` Steen Hegelund
2020-12-17 7:51 ` [RFC PATCH v2 3/8] net: sparx5: add hostmode with phylink support Steen Hegelund
2020-12-19 19:51 ` Andrew Lunn
2020-12-22 9:46 ` Steen Hegelund
2020-12-22 14:41 ` Andrew Lunn
2020-12-23 13:29 ` Steen Hegelund
2020-12-23 20:58 ` Alexandre Belloni
2020-12-23 21:05 ` Andrew Lunn [this message]
2020-12-17 7:51 ` [RFC PATCH v2 4/8] net: sparx5: add port module support Steen Hegelund
2020-12-20 23:35 ` Andrew Lunn
2020-12-22 14:55 ` Bjarni Jonasson
2020-12-22 15:08 ` Andrew Lunn
2020-12-17 7:51 ` [RFC PATCH v2 5/8] net: sparx5: add switching, vlan and mactable support Steen Hegelund
2020-12-21 0:25 ` Andrew Lunn
2020-12-23 13:54 ` Steen Hegelund
2020-12-17 7:51 ` [RFC PATCH v2 6/8] net: sparx5: add calendar bandwidth allocation support Steen Hegelund
2020-12-17 7:51 ` [RFC PATCH v2 7/8] net: sparx5: add ethtool configuration and statistics support Steen Hegelund
2020-12-19 23:31 ` Andrew Lunn
2020-12-17 7:51 ` [RFC PATCH v2 8/8] arm64: dts: sparx5: Add the Sparx5 switch node Steen Hegelund
2020-12-19 20:24 ` Andrew Lunn
2020-12-23 14:31 ` Steen Hegelund
2020-12-23 15:49 ` Andrew Lunn
2020-12-21 0:58 ` [RFC PATCH v2 0/8] Adding the Sparx5 Switch Driver Florian Fainelli
2020-12-21 14:31 ` Steen Hegelund
2020-12-22 11:29 ` Lars Povlsen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20201223210521.GB3253993@lunn.ch \
--to=andrew@lunn.ch \
--cc=UNGLinuxDriver@microchip.com \
--cc=alexandre.belloni@bootlin.com \
--cc=arnd@arndb.de \
--cc=bjarni.jonasson@microchip.com \
--cc=davem@davemloft.net \
--cc=kuba@kernel.org \
--cc=lars.povlsen@microchip.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=madalin.bucur@oss.nxp.com \
--cc=mark.einon@gmail.com \
--cc=masahiroy@kernel.org \
--cc=netdev@vger.kernel.org \
--cc=nicolas.ferre@microchip.com \
--cc=steen.hegelund@microchip.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®