From: Alain Volmat <avolmat@me.com>
To: patrice.chotard@st.com, robh+dt@kernel.org, mark.rutland@arm.com,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Cc: avolmat@me.com
Subject: [PATCH 04/12] ARM: dts: sti: move some nodes out of the soc section in stih407-family.dtsi
Date: Thu, 2 Dec 2021 08:50:57 +0100 [thread overview]
Message-ID: <20211202075105.195664-5-avolmat@me.com> (raw)
In-Reply-To: <20211202075105.195664-1-avolmat@me.com>
Move all nodes without reg property out of the soc section of
stih407-family.dtsi. This avoid to set a <0> reg property.
Signed-off-by: Alain Volmat <avolmat@me.com>
---
arch/arm/boot/dts/stih407-family.dtsi | 262 +++++++++++++-------------
1 file changed, 126 insertions(+), 136 deletions(-)
diff --git a/arch/arm/boot/dts/stih407-family.dtsi b/arch/arm/boot/dts/stih407-family.dtsi
index 21f3347a91d6..1713f7878117 100644
--- a/arch/arm/boot/dts/stih407-family.dtsi
+++ b/arch/arm/boot/dts/stih407-family.dtsi
@@ -115,37 +115,140 @@ pwm_regulator: pwm-regulator {
status = "okay";
};
- soc {
- #address-cells = <1>;
- #size-cells = <1>;
- interrupt-parent = <&intc>;
+ restart: restart-controller {
+ compatible = "st,stih407-restart";
+ st,syscfg = <&syscfg_sbc_reg>;
+ status = "okay";
+ };
+
+ powerdown: powerdown-controller {
+ compatible = "st,stih407-powerdown";
+ #reset-cells = <1>;
+ };
+
+ softreset: softreset-controller {
+ compatible = "st,stih407-softreset";
+ #reset-cells = <1>;
+ };
+
+ picophyreset: picophyreset-controller {
+ compatible = "st,stih407-picophyreset";
+ #reset-cells = <1>;
+ };
+
+ irq-syscfg {
+ compatible = "st,stih407-irq-syscfg";
+ st,syscfg = <&syscfg_core>;
+ st,irq-device = <ST_IRQ_SYSCFG_PMU_0>,
+ <ST_IRQ_SYSCFG_PMU_1>;
+ st,fiq-device = <ST_IRQ_SYSCFG_DISABLED>,
+ <ST_IRQ_SYSCFG_DISABLED>;
+ };
+
+ usb2_picophy0: phy1 {
+ compatible = "st,stih407-usb2-phy";
+ #phy-cells = <0>;
+ st,syscfg = <&syscfg_core 0x100 0xf4>;
+ resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
+ <&picophyreset STIH407_PICOPHY2_RESET>;
+ reset-names = "global", "port";
+ };
+
+ miphy28lp_phy: miphy28lp {
+ compatible = "st,miphy28lp-phy";
+ st,syscfg = <&syscfg_core>;
+ #address-cells = <1>;
+ #size-cells = <1>;
ranges;
- compatible = "simple-bus";
- restart: restart-controller@0 {
- compatible = "st,stih407-restart";
- reg = <0 0>;
- st,syscfg = <&syscfg_sbc_reg>;
- status = "okay";
- };
+ phy_port0: port@9b22000 {
+ reg = <0x9b22000 0xff>,
+ <0x9b09000 0xff>,
+ <0x9b04000 0xff>;
+ reg-names = "sata-up",
+ "pcie-up",
+ "pipew";
+
+ st,syscfg = <0x114 0x818 0xe0 0xec>;
+ #phy-cells = <1>;
- powerdown: powerdown-controller@0 {
- compatible = "st,stih407-powerdown";
- reg = <0 0>;
- #reset-cells = <1>;
+ reset-names = "miphy-sw-rst";
+ resets = <&softreset STIH407_MIPHY0_SOFTRESET>;
};
- softreset: softreset-controller@0 {
- compatible = "st,stih407-softreset";
- reg = <0 0>;
- #reset-cells = <1>;
+ phy_port1: port@9b2a000 {
+ reg = <0x9b2a000 0xff>,
+ <0x9b19000 0xff>,
+ <0x9b14000 0xff>;
+ reg-names = "sata-up",
+ "pcie-up",
+ "pipew";
+
+ st,syscfg = <0x118 0x81c 0xe4 0xf0>;
+
+ #phy-cells = <1>;
+
+ reset-names = "miphy-sw-rst";
+ resets = <&softreset STIH407_MIPHY1_SOFTRESET>;
};
- picophyreset: picophyreset-controller@0 {
- compatible = "st,stih407-picophyreset";
- reg = <0 0>;
- #reset-cells = <1>;
+ phy_port2: port@8f95000 {
+ reg = <0x8f95000 0xff>,
+ <0x8f90000 0xff>;
+ reg-names = "pipew",
+ "usb3-up";
+
+ st,syscfg = <0x11c 0x820>;
+
+ #phy-cells = <1>;
+
+ reset-names = "miphy-sw-rst";
+ resets = <&softreset STIH407_MIPHY2_SOFTRESET>;
};
+ };
+
+ st231_gp0: st231-gp0 {
+ compatible = "st,st231-rproc";
+ memory-region = <&gp0_reserved>;
+ resets = <&softreset STIH407_ST231_GP0_SOFTRESET>;
+ reset-names = "sw_reset";
+ clocks = <&clk_s_c0_flexgen CLK_ST231_GP_0>;
+ clock-frequency = <600000000>;
+ st,syscfg = <&syscfg_core 0x22c>;
+ #mbox-cells = <1>;
+ mbox-names = "vq0_rx", "vq0_tx", "vq1_rx", "vq1_tx";
+ mboxes = <&mailbox0 0 2>, <&mailbox2 0 1>, <&mailbox0 0 3>, <&mailbox2 0 0>;
+ };
+
+ st231_delta: st231-delta {
+ compatible = "st,st231-rproc";
+ memory-region = <&delta_reserved>;
+ resets = <&softreset STIH407_ST231_DMU_SOFTRESET>;
+ reset-names = "sw_reset";
+ clocks = <&clk_s_c0_flexgen CLK_ST231_DMU>;
+ clock-frequency = <600000000>;
+ st,syscfg = <&syscfg_core 0x224>;
+ #mbox-cells = <1>;
+ mbox-names = "vq0_rx", "vq0_tx", "vq1_rx", "vq1_tx";
+ mboxes = <&mailbox0 0 0>, <&mailbox3 0 1>, <&mailbox0 0 1>, <&mailbox3 0 0>;
+ };
+
+ delta0 {
+ compatible = "st,st-delta";
+ clock-names = "delta",
+ "delta-st231",
+ "delta-flash-promip";
+ clocks = <&clk_s_c0_flexgen CLK_VID_DMU>,
+ <&clk_s_c0_flexgen CLK_ST231_DMU>,
+ <&clk_s_c0_flexgen CLK_FLASH_PROMIP>;
+ };
+
+ soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupt-parent = <&intc>;
+ ranges;
+ compatible = "simple-bus";
syscfg_sbc: sbc-syscfg@9620000 {
compatible = "st,stih407-sbc-syscfg", "syscon";
@@ -189,16 +292,6 @@ syscfg_lpm: lpm-syscfg@94b5100 {
reg = <0x94b5100 0x1000>;
};
- irq-syscfg@0 {
- compatible = "st,stih407-irq-syscfg";
- reg = <0 0>;
- st,syscfg = <&syscfg_core>;
- st,irq-device = <ST_IRQ_SYSCFG_PMU_0>,
- <ST_IRQ_SYSCFG_PMU_1>;
- st,fiq-device = <ST_IRQ_SYSCFG_DISABLED>,
- <ST_IRQ_SYSCFG_DISABLED>;
- };
-
/* Display */
vtg_main: sti-vtg-main@8d02800 {
compatible = "st,vtg";
@@ -389,70 +482,6 @@ i2c@9541000 {
status = "disabled";
};
- usb2_picophy0: phy1@0 {
- compatible = "st,stih407-usb2-phy";
- reg = <0 0>;
- #phy-cells = <0>;
- st,syscfg = <&syscfg_core 0x100 0xf4>;
- resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
- <&picophyreset STIH407_PICOPHY2_RESET>;
- reset-names = "global", "port";
- };
-
- miphy28lp_phy: miphy28lp@0 {
- compatible = "st,miphy28lp-phy";
- st,syscfg = <&syscfg_core>;
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- reg = <0 0>;
-
- phy_port0: port@9b22000 {
- reg = <0x9b22000 0xff>,
- <0x9b09000 0xff>,
- <0x9b04000 0xff>;
- reg-names = "sata-up",
- "pcie-up",
- "pipew";
-
- st,syscfg = <0x114 0x818 0xe0 0xec>;
- #phy-cells = <1>;
-
- reset-names = "miphy-sw-rst";
- resets = <&softreset STIH407_MIPHY0_SOFTRESET>;
- };
-
- phy_port1: port@9b2a000 {
- reg = <0x9b2a000 0xff>,
- <0x9b19000 0xff>,
- <0x9b14000 0xff>;
- reg-names = "sata-up",
- "pcie-up",
- "pipew";
-
- st,syscfg = <0x118 0x81c 0xe4 0xf0>;
-
- #phy-cells = <1>;
-
- reset-names = "miphy-sw-rst";
- resets = <&softreset STIH407_MIPHY1_SOFTRESET>;
- };
-
- phy_port2: port@8f95000 {
- reg = <0x8f95000 0xff>,
- <0x8f90000 0xff>;
- reg-names = "pipew",
- "usb3-up";
-
- st,syscfg = <0x11c 0x820>;
-
- #phy-cells = <1>;
-
- reset-names = "miphy-sw-rst";
- resets = <&softreset STIH407_MIPHY2_SOFTRESET>;
- };
- };
-
spi@9840000 {
compatible = "st,comms-ssc4-spi";
reg = <0x9840000 0x110>;
@@ -815,34 +844,6 @@ mailbox3: mailbox@8f03000 {
status = "okay";
};
- st231_gp0: st231-gp0@0 {
- compatible = "st,st231-rproc";
- reg = <0 0>;
- memory-region = <&gp0_reserved>;
- resets = <&softreset STIH407_ST231_GP0_SOFTRESET>;
- reset-names = "sw_reset";
- clocks = <&clk_s_c0_flexgen CLK_ST231_GP_0>;
- clock-frequency = <600000000>;
- st,syscfg = <&syscfg_core 0x22c>;
- #mbox-cells = <1>;
- mbox-names = "vq0_rx", "vq0_tx", "vq1_rx", "vq1_tx";
- mboxes = <&mailbox0 0 2>, <&mailbox2 0 1>, <&mailbox0 0 3>, <&mailbox2 0 0>;
- };
-
- st231_delta: st231-delta@0 {
- compatible = "st,st231-rproc";
- reg = <0 0>;
- memory-region = <&delta_reserved>;
- resets = <&softreset STIH407_ST231_DMU_SOFTRESET>;
- reset-names = "sw_reset";
- clocks = <&clk_s_c0_flexgen CLK_ST231_DMU>;
- clock-frequency = <600000000>;
- st,syscfg = <&syscfg_core 0x224>;
- #mbox-cells = <1>;
- mbox-names = "vq0_rx", "vq0_tx", "vq1_rx", "vq1_tx";
- mboxes = <&mailbox0 0 0>, <&mailbox3 0 1>, <&mailbox0 0 1>, <&mailbox3 0 0>;
- };
-
/* fdma audio */
fdma0: dma-controller@8e20000 {
compatible = "st,stih407-fdma-mpe31-11", "st,slim-rproc";
@@ -986,16 +987,5 @@ sti_uni_reader1: sti-uni-reader@8d84000 {
status = "disabled";
};
-
- delta0@0 {
- compatible = "st,st-delta";
- reg = <0 0>;
- clock-names = "delta",
- "delta-st231",
- "delta-flash-promip";
- clocks = <&clk_s_c0_flexgen CLK_VID_DMU>,
- <&clk_s_c0_flexgen CLK_ST231_DMU>,
- <&clk_s_c0_flexgen CLK_FLASH_PROMIP>;
- };
};
};
--
2.25.1
next prev parent reply other threads:[~2021-12-02 7:53 UTC|newest]
Thread overview: 27+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-12-02 7:50 [PATCH 00/12] ARM: dts: sti: various DT fixes to avoid warnings Alain Volmat
2021-12-02 7:50 ` [PATCH 01/12] ARM: dts: sti: ensure unique unit-address in stih407-clock Alain Volmat
2022-02-10 8:35 ` Patrice CHOTARD
2021-12-02 7:50 ` [PATCH 02/12] ARM: dts: sti: ensure unique unit-address in stih410-clock Alain Volmat
2022-02-10 8:36 ` Patrice CHOTARD
2021-12-02 7:50 ` [PATCH 03/12] ARM: dts: sti: ensure unique unit-address in stih418-clock Alain Volmat
2022-02-10 8:36 ` Patrice CHOTARD
2021-12-02 7:50 ` Alain Volmat [this message]
2022-02-10 8:36 ` [PATCH 04/12] ARM: dts: sti: move some nodes out of the soc section in stih407-family.dtsi Patrice CHOTARD
2021-12-02 7:50 ` [PATCH 05/12] ARM: dts: sti: update stih410-b2260 following stih407-family DT update Alain Volmat
2022-02-10 8:36 ` Patrice CHOTARD
2021-12-02 7:50 ` [PATCH 06/12] ARM: dts: sti: update stih418-b2199 " Alain Volmat
2022-02-10 8:37 ` Patrice CHOTARD
2021-12-02 7:51 ` [PATCH 07/12] ARM: dts: sti: update stihxxx-b2120 " Alain Volmat
2022-02-10 8:37 ` Patrice CHOTARD
2021-12-02 7:51 ` [PATCH 08/12] ARM: dts: sti: remove delta node from stih410.dtsi Alain Volmat
2022-02-10 8:37 ` Patrice CHOTARD
2021-12-02 7:51 ` [PATCH 09/12] ARM: dts: sti: move usb picophy nodes out of soc in stih410.dtsi Alain Volmat
2022-02-10 8:37 ` Patrice CHOTARD
2021-12-02 7:51 ` [PATCH 10/12] ARM: dts: sti: move usb picophy nodes out of soc in stih418.dtsi Alain Volmat
2022-02-10 8:37 ` Patrice CHOTARD
2021-12-02 7:51 ` [PATCH 11/12] ARM: dts: sti: move usb picophy nodes in stih410-b2120.dts Alain Volmat
2022-02-10 8:57 ` Patrice CHOTARD
2021-12-02 7:51 ` [PATCH 12/12] ARM: dts: sti: move usb picophy nodes in stih410-b2260.dts Alain Volmat
2022-02-10 8:38 ` Patrice CHOTARD
2022-02-10 8:59 ` [PATCH 00/12] ARM: dts: sti: various DT fixes to avoid warnings Patrice CHOTARD
2022-02-11 18:13 ` Alain Volmat
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20211202075105.195664-5-avolmat@me.com \
--to=avolmat@me.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=patrice.chotard@st.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®