From: Neil Armstrong <narmstrong@baylibre.com>
To: davem@davemloft.net
Cc: Neil Armstrong <narmstrong@baylibre.com>,
netdev@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-oxnas@groups.io, linux-kernel@vger.kernel.org
Subject: [PATCH net-next 2/3] net: stmmac: dwmac-oxnas: Add support for OX810SE
Date: Mon, 3 Jan 2022 18:56:37 +0100 [thread overview]
Message-ID: <20220103175638.89625-3-narmstrong@baylibre.com> (raw)
In-Reply-To: <20220103175638.89625-1-narmstrong@baylibre.com>
Add support for OX810SE dwmac glue setup, which is a simplified version
of the OX820 introduced later with more control on the PHY interface.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
.../net/ethernet/stmicro/stmmac/dwmac-oxnas.c | 92 ++++++++++++++-----
1 file changed, 70 insertions(+), 22 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-oxnas.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-oxnas.c
index adfeb8d3293d..7ffa4a4eb30f 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-oxnas.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-oxnas.c
@@ -12,6 +12,7 @@
#include <linux/io.h>
#include <linux/module.h>
#include <linux/of.h>
+#include <linux/of_device.h>
#include <linux/platform_device.h>
#include <linux/regmap.h>
#include <linux/mfd/syscon.h>
@@ -48,12 +49,58 @@
#define DWMAC_RX_VARDELAY(d) ((d) << DWMAC_RX_VARDELAY_SHIFT)
#define DWMAC_RXN_VARDELAY(d) ((d) << DWMAC_RXN_VARDELAY_SHIFT)
+struct oxnas_dwmac;
+
+struct oxnas_dwmac_data {
+ void (*setup)(struct oxnas_dwmac *dwmac);
+};
+
struct oxnas_dwmac {
struct device *dev;
struct clk *clk;
struct regmap *regmap;
+ const struct oxnas_dwmac_data *data;
};
+static void oxnas_dwmac_setup_ox810se(struct oxnas_dwmac *dwmac)
+{
+ unsigned int value;
+
+ /* Enable GMII_GTXCLK to follow GMII_REFCLK, required for gigabit PHY */
+ value = BIT(DWMAC_CKEN_GTX) |
+ /* Use simple mux for 25/125 Mhz clock switching */
+ BIT(DWMAC_SIMPLE_MUX);
+
+ regmap_write(dwmac->regmap, OXNAS_DWMAC_CTRL_REGOFFSET, value);
+}
+
+static void oxnas_dwmac_setup_ox820(struct oxnas_dwmac *dwmac)
+{
+ unsigned int value;
+
+ /* Enable GMII_GTXCLK to follow GMII_REFCLK, required for gigabit PHY */
+ value = BIT(DWMAC_CKEN_GTX) |
+ /* Use simple mux for 25/125 Mhz clock switching */
+ BIT(DWMAC_SIMPLE_MUX) |
+ /* set auto switch tx clock source */
+ BIT(DWMAC_AUTO_TX_SOURCE) |
+ /* enable tx & rx vardelay */
+ BIT(DWMAC_CKEN_TX_OUT) |
+ BIT(DWMAC_CKEN_TXN_OUT) |
+ BIT(DWMAC_CKEN_TX_IN) |
+ BIT(DWMAC_CKEN_RX_OUT) |
+ BIT(DWMAC_CKEN_RXN_OUT) |
+ BIT(DWMAC_CKEN_RX_IN);
+ regmap_write(dwmac->regmap, OXNAS_DWMAC_CTRL_REGOFFSET, value);
+
+ /* set tx & rx vardelay */
+ value = DWMAC_TX_VARDELAY(4) |
+ DWMAC_TXN_VARDELAY(2) |
+ DWMAC_RX_VARDELAY(10) |
+ DWMAC_RXN_VARDELAY(8);
+ regmap_write(dwmac->regmap, OXNAS_DWMAC_DELAY_REGOFFSET, value);
+}
+
static int oxnas_dwmac_init(struct platform_device *pdev, void *priv)
{
struct oxnas_dwmac *dwmac = priv;
@@ -75,27 +122,7 @@ static int oxnas_dwmac_init(struct platform_device *pdev, void *priv)
return ret;
}
- /* Enable GMII_GTXCLK to follow GMII_REFCLK, required for gigabit PHY */
- value |= BIT(DWMAC_CKEN_GTX) |
- /* Use simple mux for 25/125 Mhz clock switching */
- BIT(DWMAC_SIMPLE_MUX) |
- /* set auto switch tx clock source */
- BIT(DWMAC_AUTO_TX_SOURCE) |
- /* enable tx & rx vardelay */
- BIT(DWMAC_CKEN_TX_OUT) |
- BIT(DWMAC_CKEN_TXN_OUT) |
- BIT(DWMAC_CKEN_TX_IN) |
- BIT(DWMAC_CKEN_RX_OUT) |
- BIT(DWMAC_CKEN_RXN_OUT) |
- BIT(DWMAC_CKEN_RX_IN);
- regmap_write(dwmac->regmap, OXNAS_DWMAC_CTRL_REGOFFSET, value);
-
- /* set tx & rx vardelay */
- value = DWMAC_TX_VARDELAY(4) |
- DWMAC_TXN_VARDELAY(2) |
- DWMAC_RX_VARDELAY(10) |
- DWMAC_RXN_VARDELAY(8);
- regmap_write(dwmac->regmap, OXNAS_DWMAC_DELAY_REGOFFSET, value);
+ dwmac->data->setup(dwmac);
return 0;
}
@@ -128,6 +155,12 @@ static int oxnas_dwmac_probe(struct platform_device *pdev)
goto err_remove_config_dt;
}
+ dwmac->data = (const struct oxnas_dwmac_data *)of_device_get_match_data(&pdev->dev);
+ if (!dwmac->data) {
+ ret = -EINVAL;
+ goto err_remove_config_dt;
+ }
+
dwmac->dev = &pdev->dev;
plat_dat->bsp_priv = dwmac;
plat_dat->init = oxnas_dwmac_init;
@@ -166,8 +199,23 @@ static int oxnas_dwmac_probe(struct platform_device *pdev)
return ret;
}
+static const struct oxnas_dwmac_data ox810se_dwmac_data = {
+ .setup = oxnas_dwmac_setup_ox810se,
+};
+
+static const struct oxnas_dwmac_data ox820_dwmac_data = {
+ .setup = oxnas_dwmac_setup_ox820,
+};
+
static const struct of_device_id oxnas_dwmac_match[] = {
- { .compatible = "oxsemi,ox820-dwmac" },
+ {
+ .compatible = "oxsemi,ox810se-dwmac",
+ .data = &ox810se_dwmac_data,
+ },
+ {
+ .compatible = "oxsemi,ox820-dwmac",
+ .data = &ox820_dwmac_data,
+ },
{ }
};
MODULE_DEVICE_TABLE(of, oxnas_dwmac_match);
--
2.25.1
next prev parent reply other threads:[~2022-01-03 17:56 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-01-03 17:56 [PATCH 0/3] ARM: ox810se: Add Ethernet support Neil Armstrong
2022-01-03 17:56 ` [PATCH net-next 1/3] dt-bindings: net: oxnas-dwmac: Add bindings for OX810SE Neil Armstrong
2022-01-03 17:56 ` Neil Armstrong [this message]
2022-01-04 8:42 ` [PATCH net-next 2/3] net: stmmac: dwmac-oxnas: Add support " Neil Armstrong
2022-01-04 4:06 ` [PATCH 0/3] ARM: ox810se: Add Ethernet support Jakub Kicinski
2022-01-04 8:10 ` Neil Armstrong
2022-01-04 8:11 ` [PATCH 3/3] ARM: dts: " Neil Armstrong
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220103175638.89625-3-narmstrong@baylibre.com \
--to=narmstrong@baylibre.com \
--cc=davem@davemloft.net \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-oxnas@groups.io \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®