mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Jon Lin <jon.lin@rock-chips.com>
To: broonie@kernel.org
Cc: heiko@sntech.de, linux-spi@vger.kernel.org,
	linux-arm-kernel@lists.infradead.org,
	linux-rockchip@lists.infradead.org, linux-kernel@vger.kernel.org,
	Jon Lin <jon.lin@rock-chips.com>
Subject: [PATCH v3 4/6] spi: rockchip: Preset cs-high and clk polarity in setup progress
Date: Wed, 16 Feb 2022 09:40:26 +0800	[thread overview]
Message-ID: <20220216014028.8123-5-jon.lin@rock-chips.com> (raw)
In-Reply-To: <20220216014028.8123-1-jon.lin@rock-chips.com>

After power up, the cs and clock is in default status, and the cs-high
and clock polarity dts property configuration will take no effect until
the calling of rockchip_spi_config in the first transmission.
So preset them to make sure a correct voltage before the first
transmission coming.

Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
---

Changes in v3:
- Support clear the bits of configure bits filed

Changes in v2:
- Limit cs-high presetting to the chip select n <= 1

Changes in v1: None

 drivers/spi/spi-rockchip.c | 24 ++++++++++++++++++++++++
 1 file changed, 24 insertions(+)

diff --git a/drivers/spi/spi-rockchip.c b/drivers/spi/spi-rockchip.c
index 5ecd0692cca1..83da8fdb3c02 100644
--- a/drivers/spi/spi-rockchip.c
+++ b/drivers/spi/spi-rockchip.c
@@ -713,6 +713,29 @@ static bool rockchip_spi_can_dma(struct spi_controller *ctlr,
 	return xfer->len / bytes_per_word >= rs->fifo_len;
 }
 
+static int rockchip_spi_setup(struct spi_device *spi)
+{
+	struct rockchip_spi *rs = spi_controller_get_devdata(spi->controller);
+	u32 cr0;
+
+	pm_runtime_get_sync(rs->dev);
+
+	cr0 = readl_relaxed(rs->regs + ROCKCHIP_SPI_CTRLR0);
+
+	cr0 &= ~(0x3 << CR0_SCPH_OFFSET);
+	cr0 |= ((spi->mode & 0x3) << CR0_SCPH_OFFSET);
+	if (spi->mode & SPI_CS_HIGH && spi->chip_select <= 1)
+		cr0 |= BIT(spi->chip_select) << CR0_SOI_OFFSET;
+	else if (spi->chip_select <= 1)
+		cr0 &= ~(BIT(spi->chip_select) << CR0_SOI_OFFSET);
+
+	writel_relaxed(cr0, rs->regs + ROCKCHIP_SPI_CTRLR0);
+
+	pm_runtime_put(rs->dev);
+
+	return 0;
+}
+
 static int rockchip_spi_probe(struct platform_device *pdev)
 {
 	int ret;
@@ -840,6 +863,7 @@ static int rockchip_spi_probe(struct platform_device *pdev)
 	ctlr->min_speed_hz = rs->freq / BAUDR_SCKDV_MAX;
 	ctlr->max_speed_hz = min(rs->freq / BAUDR_SCKDV_MIN, MAX_SCLK_OUT);
 
+	ctlr->setup = rockchip_spi_setup;
 	ctlr->set_cs = rockchip_spi_set_cs;
 	ctlr->transfer_one = rockchip_spi_transfer_one;
 	ctlr->max_transfer_size = rockchip_spi_max_transfer_size;
-- 
2.17.1


  parent reply	other threads:[~2022-02-16  1:41 UTC|newest]

Thread overview: 12+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2022-02-16  1:40 [PATCH v3 0/6] New support and problem adjustment of SPI rockchip Jon Lin
2022-02-16  1:40 ` [PATCH v3 1/6] spi: rockchip: Fix error in getting num-cs property Jon Lin
2022-02-16  1:40 ` [PATCH v3 2/6] spi: rockchip: terminate dma transmission when slave abort Jon Lin
2022-02-16  1:40 ` [PATCH v3 3/6] spi: rockchip: Stop spi slave dma receiver when cs inactive Jon Lin
2022-02-16  1:40 ` Jon Lin [this message]
2022-02-16  1:40 ` [PATCH v3 5/6] spi: rockchip: Suspend and resume the bus during NOIRQ_SYSTEM_SLEEP_PM ops Jon Lin
2022-06-21 15:42   ` Ondřej Jirman
2024-08-23 21:28     ` Brian Norris
     [not found]       ` <f836c6fe-3edc-4e6b-aa83-b50d9edcb816@rock-chips.com>
2024-08-26 18:30         ` Brian Norris
2022-02-16  1:40 ` [PATCH v3 6/6] spi: rockchip: clear interrupt status in error handler Jon Lin
2022-02-17 16:22 ` (subset) [PATCH v3 0/6] New support and problem adjustment of SPI rockchip Mark Brown
2022-02-17 18:32 ` Mark Brown

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20220216014028.8123-5-jon.lin@rock-chips.com \
    --to=jon.lin@rock-chips.com \
    --cc=broonie@kernel.org \
    --cc=heiko@sntech.de \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-rockchip@lists.infradead.org \
    --cc=linux-spi@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®