From: Henning Schild <henning.schild@siemens.com>
To: simon.guinot@sequanux.org
Cc: Linus Walleij <linus.walleij@linaro.org>,
Bartosz Golaszewski <brgl@bgdev.pl>, Pavel Machek <pavel@ucw.cz>,
Hans de Goede <hdegoede@redhat.com>,
Mark Gross <markgross@kernel.org>,
Andy Shevchenko <andriy.shevchenko@linux.intel.com>,
Lee Jones <lee@kernel.org>,
linux-gpio@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-leds@vger.kernel.org, platform-driver-x86@vger.kernel.org,
Sheng-Yuan Huang <syhuang3@nuvoton.com>,
Tasanakorn Phaipool <tasanakorn@gmail.com>
Subject: Re: [PATCH v3 1/4] gpio-f7188x: Add GPIO support for Nuvoton NCT6116
Date: Tue, 23 Aug 2022 11:26:15 +0200 [thread overview]
Message-ID: <20220823112615.2e2a96b7@md1za8fc.ad001.siemens.net> (raw)
In-Reply-To: <YvY33D9YLm7/g14N@76cbfcf04d45>
Am Fri, 12 Aug 2022 13:22:04 +0200
schrieb simon.guinot@sequanux.org:
> On Fri, Aug 12, 2022 at 12:23:12PM +0200, Henning Schild wrote:
> > Am Fri, 12 Aug 2022 10:43:03 +0200
> > schrieb simon.guinot@sequanux.org:
> >
> > > On Thu, Aug 11, 2022 at 05:39:05PM +0200, Henning Schild wrote:
> > > > Add GPIO support for Nuvoton NCT6116 chip. Nuvoton SuperIO
> > > > chips are very similar to the ones from Fintek. In other
> > > > subsystems they also share drivers and are called a family of
> > > > drivers.
> > > >
> > > > For the GPIO subsystem the only difference is that the direction
> > > > bit is reversed and that there is only one data bit per pin. On
> > > > the SuperIO level the logical device is another one.
> > > >
> > > > Signed-off-by: Henning Schild <henning.schild@siemens.com>
> > > > ---
> > > > drivers/gpio/gpio-f7188x.c | 71
> > > > +++++++++++++++++++++++++++----------- 1 file changed, 51
> > > > insertions(+), 20 deletions(-)
> > > >
> > > > diff --git a/drivers/gpio/gpio-f7188x.c
> > > > b/drivers/gpio/gpio-f7188x.c index 18a3147f5a42..7b05ecc611e9
> > > > 100644 --- a/drivers/gpio/gpio-f7188x.c
> > > > +++ b/drivers/gpio/gpio-f7188x.c
> > > > @@ -1,6 +1,7 @@
> > > > // SPDX-License-Identifier: GPL-2.0-or-later
> > > > /*
> > > > * GPIO driver for Fintek Super-I/O F71869, F71869A, F71882,
> > > > F71889 and F81866
> > > > + * and Nuvoton Super-I/O NCT6116D
> > > > *
> > > > * Copyright (C) 2010-2013 LaCie
> > > > *
> > > > @@ -22,13 +23,12 @@
> > > > #define SIO_LDSEL 0x07 /* Logical device
> > > > select */ #define SIO_DEVID 0x20 /*
> > > > Device ID (2 bytes) */ #define SIO_DEVREV
> > > > 0x22 /* Device revision */ -#define SIO_MANID
> > > > 0x23 /* Fintek ID (2 bytes) */
> > > > -#define SIO_LD_GPIO 0x06 /* GPIO logical
> > > > device */ #define SIO_UNLOCK_KEY 0x87 /*
> > > > Key to enable Super-I/O */ #define SIO_LOCK_KEY
> > > > 0xAA /* Key to disable Super-I/O */
> > > > -#define SIO_FINTEK_ID 0x1934 /*
> > > > Manufacturer ID */ +#define SIO_LD_GPIO_FINTEK
> > > > 0x06 /* GPIO logical device */ +#define
> > > > SIO_LD_GPIO_NUVOTON 0x07 /* GPIO logical device */
> > >
> > > Please indulge me and add a new line here.
> >
> > Mhh ... how about you write exactly how you would like to have that
> > define block. So we do not have taste issues in the next round.
>
> Sure. Considering the manufacturer IDs you have to keep and add, I
> would go with your original approach (i.e. a section per
> manufacturer). But I would add extra new lines and comments and use a
> sligthly different namming for the LD_GPIO definitions.
>
> /*
> * Super-I/O registers
> */
> #define SIO_LDSEL 0x07 /* Logical device select */
> #define SIO_DEVID 0x20 /* Device ID (2 bytes) */
> #define SIO_DEVREV 0x22 /* Device revision */
> #define SIO_MANID 0x23 /* Fintek ID (2 bytes) */
>
> #define SIO_UNLOCK_KEY 0x87 /* Key to enable Super-I/O */
> #define SIO_LOCK_KEY 0xAA /* Key to disable Super-I/O */
>
> /*
> * Fintek devices.
> */
> #define SIO_FINTEK_ID 0x1934 /* Manufacturer ID */
>
> #define SIO_F71869_ID 0x0814 /* F71869 chipset ID */
> #define SIO_F71869A_ID 0x1007 /* F71869A chipset ID */
> #define SIO_F71882_ID 0x0541 /* F71882 chipset ID */
> #define SIO_F71889_ID 0x0909 /* F71889 chipset ID */
> #define SIO_F71889A_ID 0x1005 /* F71889A chipset ID */
> #define SIO_F81866_ID 0x1010 /* F81866 chipset ID */
> #define SIO_F81804_ID 0x1502 /* F81804 chipset ID, same for
> f81966 */
> #define SIO_F81865_ID 0x0704 /* F81865 chipset ID */
>
> #define SIO_FINTEK_LD_GPIO 0x06 /* GPIO logical device */
>
> /*
> * Nuvoton devices.
> */
> #define SIO_NUVOTON_ID 0xXXXX /* Manufacturer ID */
>
> #define SIO_NCT6116D_ID 0xD283 /* NCT6116D chipset ID */
>
> #define SIO_NUVOTON_LD_GPIO 0x07 /* GPIO logical device */
>
> Please, note it is not only a matter of taste. New lines and comments
> are really helping the reader. Also, note that I am not asking for
> this change, only suggesting it.
This is fine. I will take this. Only slight difference will be in the
revid and manid, those are Fintek specific and do not apply for Nuvoton.
regards,
Henning
> >
> > > > #define SIO_F71869_ID 0x0814 /* F71869
> > > > chipset ID */ #define SIO_F71869A_ID 0x1007
> > > > /* F71869A chipset ID */ #define SIO_F71882_ID
> > > > 0x0541 /* F71882 chipset ID */ @@ -37,7 +37,7 @@
> > > > #define SIO_F81866_ID 0x1010 /* F81866
> > > > chipset ID */ #define SIO_F81804_ID 0x1502 /*
> > > > F81804 chipset ID, same for f81966 */ #define SIO_F81865_ID
> > > > 0x0704 /* F81865 chipset ID */ -
> > > > +#define SIO_NCT6116D_ID 0xD283 /* NCT6116D
> > > > chipset ID */
> > >
> > > ... snip ...
> > >
> > > > @@ -485,12 +516,8 @@ static int __init f7188x_find(int addr,
> > > > struct f7188x_sio *sio) return err;
> > > >
> > > > err = -ENODEV;
> > > > - devid = superio_inw(addr, SIO_MANID);
> > > > - if (devid != SIO_FINTEK_ID) {
> > > > - pr_debug(DRVNAME ": Not a Fintek device at
> > > > 0x%08x\n", addr);
> > > > - goto err;
> > > > - }
> > >
> > > Sorry for missing that at my first review. You can't remove this
> > > block of code. This driver is poking around on the I2C bus, which
> > > is not great. So we want to make sure as much as possible that we
> > > are speaking to the right device.
> >
> > Ok fair enough, we can make that more conservative and match the two
> > manufacturers and also make sure that not one can bring a chip id
> > that the other one uses for another chip.
> > A v4 is coming earliest in 1.5 weeks.
>
> Great. Thanks for your patience.
>
> Simon
next prev parent reply other threads:[~2022-08-23 11:38 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-08-11 15:39 [PATCH v3 0/4] add support for another simatic board Henning Schild
2022-08-11 15:39 ` [PATCH v3 1/4] gpio-f7188x: Add GPIO support for Nuvoton NCT6116 Henning Schild
2022-08-12 8:43 ` simon.guinot
2022-08-12 10:23 ` Henning Schild
2022-08-12 11:22 ` simon.guinot
2022-08-23 9:26 ` Henning Schild [this message]
2022-08-22 16:01 ` Henning Schild
[not found] ` <CAHp75VdgKHh+ma34pY=PzS6MB6NWNtzBAADqQmaJgT+couN1Dg@mail.gmail.com>
2022-08-22 13:26 ` Henning Schild
2022-08-22 14:58 ` Henning Schild
2022-08-11 15:39 ` [PATCH v3 2/4] gpio-f7188x: use unique labels for banks/chips Henning Schild
[not found] ` <CAHp75VdWdzsT9wc9BNNKTJ3-eBn3uWdCFXqE2TT+CiJnoTOQYw@mail.gmail.com>
2022-08-22 13:21 ` Henning Schild
2022-08-22 21:36 ` Andy Shevchenko
2022-08-26 8:31 ` Linus Walleij
2022-08-11 15:39 ` [PATCH v3 3/4] leds: simatic-ipc-leds-gpio: add new model 227G Henning Schild
2022-08-11 18:53 ` Hans de Goede
2022-08-11 15:39 ` [PATCH v3 4/4] platform/x86: simatic-ipc: enable watchdog for 227G Henning Schild
2022-08-11 18:53 ` Hans de Goede
2022-08-11 18:34 ` [PATCH v3 0/4] add support for another simatic board Henning Schild
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220823112615.2e2a96b7@md1za8fc.ad001.siemens.net \
--to=henning.schild@siemens.com \
--cc=andriy.shevchenko@linux.intel.com \
--cc=brgl@bgdev.pl \
--cc=hdegoede@redhat.com \
--cc=lee@kernel.org \
--cc=linus.walleij@linaro.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-leds@vger.kernel.org \
--cc=markgross@kernel.org \
--cc=pavel@ucw.cz \
--cc=platform-driver-x86@vger.kernel.org \
--cc=simon.guinot@sequanux.org \
--cc=syhuang3@nuvoton.com \
--cc=tasanakorn@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®