mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: quanyang.wang@windriver.com
To: Michael Turquette <mturquette@baylibre.com>,
	Stephen Boyd <sboyd@kernel.org>,
	Michal Simek <michal.simek@xilinx.com>
Cc: Michael Tretter <m.tretter@pengutronix.de>,
	Quanyang Wang <quanyang.wang@windriver.com>,
	linux-clk@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org
Subject: [PATCH] clk: zynqmp: pll: rectify rate rounding in zynqmp_pll_round_rate
Date: Fri, 26 Aug 2022 22:20:30 +0800	[thread overview]
Message-ID: <20220826142030.213805-1-quanyang.wang@windriver.com> (raw)

From: Quanyang Wang <quanyang.wang@windriver.com>

The function zynqmp_pll_round_rate is used to find a most appropriate
PLL frequency which the hardware can generate according to the desired
frequency. For example, if the desired frequency is 297MHz, considering
the limited range from PS_PLL_VCO_MIN (1.5GHz) to PS_PLL_VCO_MAX (3.0GHz)
of PLL, zynqmp_pll_round_rate should return 1.872GHz (297MHz * 5).

There are two problems with the current code of zynqmp_pll_round_rate:

1) When the rate is below PS_PLL_VCO_MIN, it can't find a correct rate
when the parameter "rate" is an integer multiple of *prate, in other words,
if "f" is zero, zynqmp_pll_round_rate won't return a valid frequency which
is from PS_PLL_VCO_MIN to PS_PLL_VCO_MAX. For example, *prate is 33MHz
and the rate is 660MHz, zynqmp_pll_round_rate will not boost up rate and
just return 660MHz, and this will cause clk_calc_new_rates failure since
zynqmp_pll_round_rate returns an invalid rate out of its boundaries.

2) Even if the rate is higher than PS_PLL_VCO_MIN, there is still a risk
that zynqmp_pll_round_rate returns an invalid rate because the function
DIV_ROUND_CLOSEST makes some loss in the fractional part. If the parent
clock *prate is 33333333Hz and we want to set the PLL rate to 1.5GHz,
this function will return 1499999985Hz by using the formula below:
    value = *prate * DIV_ROUND_CLOSEST(rate, *prate)).
This value is also invalid since it's slightly smaller than PS_PLL_VCO_MIN.
because DIV_ROUND_CLOSEST makes some loss in the fractional part.

Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
---
 drivers/clk/zynqmp/pll.c | 31 +++++++++++++++----------------
 1 file changed, 15 insertions(+), 16 deletions(-)

diff --git a/drivers/clk/zynqmp/pll.c b/drivers/clk/zynqmp/pll.c
index 91a6b4cc910e..0d3e1377b092 100644
--- a/drivers/clk/zynqmp/pll.c
+++ b/drivers/clk/zynqmp/pll.c
@@ -102,26 +102,25 @@ static long zynqmp_pll_round_rate(struct clk_hw *hw, unsigned long rate,
 				  unsigned long *prate)
 {
 	u32 fbdiv;
-	long rate_div, f;
+	u32 mult, div;
 
-	/* Enable the fractional mode if needed */
-	rate_div = (rate * FRAC_DIV) / *prate;
-	f = rate_div % FRAC_DIV;
-	if (f) {
-		if (rate > PS_PLL_VCO_MAX) {
-			fbdiv = rate / PS_PLL_VCO_MAX;
-			rate = rate / (fbdiv + 1);
-		}
-		if (rate < PS_PLL_VCO_MIN) {
-			fbdiv = DIV_ROUND_UP(PS_PLL_VCO_MIN, rate);
-			rate = rate * fbdiv;
-		}
-		return rate;
+	/* Let rate fall inside the range PS_PLL_VCO_MIN ~ PS_PLL_VCO_MAX */
+	if (rate > PS_PLL_VCO_MAX) {
+		div = DIV_ROUND_UP(rate, PS_PLL_VCO_MAX);
+		rate = rate / div;
+	}
+	if (rate < PS_PLL_VCO_MIN) {
+		mult = DIV_ROUND_UP(PS_PLL_VCO_MIN, rate);
+		rate = rate * mult;
 	}
 
 	fbdiv = DIV_ROUND_CLOSEST(rate, *prate);
-	fbdiv = clamp_t(u32, fbdiv, PLL_FBDIV_MIN, PLL_FBDIV_MAX);
-	return *prate * fbdiv;
+	if (fbdiv < PLL_FBDIV_MIN || fbdiv > PLL_FBDIV_MAX) {
+		fbdiv = clamp_t(u32, fbdiv, PLL_FBDIV_MIN, PLL_FBDIV_MAX);
+		rate = *prate * fbdiv;
+	}
+
+	return rate;
 }
 
 /**
-- 
2.36.1


             reply	other threads:[~2022-08-26 14:21 UTC|newest]

Thread overview: 3+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2022-08-26 14:20 quanyang.wang [this message]
2022-08-30  6:18 ` Datta, Shubhrajyoti
2022-08-30 22:06 ` Stephen Boyd

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20220826142030.213805-1-quanyang.wang@windriver.com \
    --to=quanyang.wang@windriver.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-clk@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=m.tretter@pengutronix.de \
    --cc=michal.simek@xilinx.com \
    --cc=mturquette@baylibre.com \
    --cc=sboyd@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®