From: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
To: Elson Roy Serrao <quic_eserrao@quicinc.com>
Cc: "gregkh@linuxfoundation.org" <gregkh@linuxfoundation.org>,
Thinh Nguyen <Thinh.Nguyen@synopsys.com>,
"balbi@kernel.org" <balbi@kernel.org>,
"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>,
"linux-usb@vger.kernel.org" <linux-usb@vger.kernel.org>,
"quic_wcheng@quicinc.com" <quic_wcheng@quicinc.com>,
"quic_jackp@quicinc.com" <quic_jackp@quicinc.com>
Subject: Re: [PATCH v7 3/5] usb: gadget: Add function wakeup support
Date: Fri, 10 Mar 2023 23:17:26 +0000 [thread overview]
Message-ID: <20230310231723.toshpghfenuymjnd@synopsys.com> (raw)
In-Reply-To: <1678393499-7366-4-git-send-email-quic_eserrao@quicinc.com>
On Thu, Mar 09, 2023, Elson Roy Serrao wrote:
> USB3.2 spec section 9.2.5.4 quotes that a function may signal that
> it wants to exit from Function Suspend by sending a Function
> Wake Notification to the host if it is enabled for function
> remote wakeup. Add an api in composite layer that can be used
> by the function drivers to support this feature. Also expose
> a gadget op so that composite layer can trigger a wakeup request
> to the UDC driver.
>
> Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
> ---
> drivers/usb/gadget/composite.c | 40 ++++++++++++++++++++++++++++++++++++++++
> include/linux/usb/composite.h | 6 ++++++
> include/linux/usb/gadget.h | 1 +
> 3 files changed, 47 insertions(+)
>
> diff --git a/drivers/usb/gadget/composite.c b/drivers/usb/gadget/composite.c
> index c9c983e..2111732 100644
> --- a/drivers/usb/gadget/composite.c
> +++ b/drivers/usb/gadget/composite.c
> @@ -492,6 +492,46 @@ int usb_interface_id(struct usb_configuration *config,
> }
> EXPORT_SYMBOL_GPL(usb_interface_id);
>
> +/**
> + * usb_func_wakeup - sends function wake notification to the host.
> + * @func: function that sends the remote wakeup notification.
> + *
> + * Applicable to devices operating at enhanced superspeed when usb
> + * functions are put in function suspend state and armed for function
> + * remote wakeup. On completion, function wake notification is sent. If
> + * the device is in low power state it tries to bring the device to active
> + * state before sending the wake notification. Since it is a synchronous
> + * call, caller must take care of not calling it in interrupt context.
> + * For devices operating at lower speeds returns negative errno.
> + *
> + * Returns zero on success, else negative errno.
> + */
> +int usb_func_wakeup(struct usb_function *func)
> +{
> + struct usb_gadget *gadget = func->config->cdev->gadget;
> + int id;
> +
> + if (!gadget->ops->func_wakeup)
> + return -EOPNOTSUPP;
> +
> + if (!func->func_wakeup_armed) {
> + ERROR(func->config->cdev, "not armed for func remote wakeup\n");
> + return -EINVAL;
> + }
> +
> + for (id = 0; id < MAX_CONFIG_INTERFACES; id++)
> + if (func->config->interface[id] == func)
> + break;
> +
> + if (id == MAX_CONFIG_INTERFACES) {
> + ERROR(func->config->cdev, "Invalid function\n");
> + return -EINVAL;
> + }
> +
> + return gadget->ops->func_wakeup(gadget, id);
> +}
> +EXPORT_SYMBOL_GPL(usb_func_wakeup);
> +
> static u8 encode_bMaxPower(enum usb_device_speed speed,
> struct usb_configuration *c)
> {
> diff --git a/include/linux/usb/composite.h b/include/linux/usb/composite.h
> index d949e91..a2448e9 100644
> --- a/include/linux/usb/composite.h
> +++ b/include/linux/usb/composite.h
> @@ -150,6 +150,9 @@ struct usb_os_desc_table {
> * GetStatus() request when the recipient is Interface.
> * @func_suspend: callback to be called when
> * SetFeature(FUNCTION_SUSPEND) is reseived
> + * @func_suspended: Indicates whether the function is in function suspend state.
> + * @func_wakeup_armed: Indicates whether the function is armed by the host for
> + * wakeup signaling.
> *
> * A single USB function uses one or more interfaces, and should in most
> * cases support operation at both full and high speeds. Each function is
> @@ -220,6 +223,8 @@ struct usb_function {
> int (*get_status)(struct usb_function *);
> int (*func_suspend)(struct usb_function *,
> u8 suspend_opt);
> + bool func_suspended;
> + bool func_wakeup_armed;
> /* private: */
> /* internals */
> struct list_head list;
> @@ -241,6 +246,7 @@ int config_ep_by_speed_and_alt(struct usb_gadget *g, struct usb_function *f,
>
> int config_ep_by_speed(struct usb_gadget *g, struct usb_function *f,
> struct usb_ep *_ep);
> +int usb_func_wakeup(struct usb_function *func);
>
> #define MAX_CONFIG_INTERFACES 16 /* arbitrary; max 255 */
>
> diff --git a/include/linux/usb/gadget.h b/include/linux/usb/gadget.h
> index 1d79612..75bda078 100644
> --- a/include/linux/usb/gadget.h
> +++ b/include/linux/usb/gadget.h
> @@ -310,6 +310,7 @@ struct usb_udc;
> struct usb_gadget_ops {
> int (*get_frame)(struct usb_gadget *);
> int (*wakeup)(struct usb_gadget *);
> + int (*func_wakeup)(struct usb_gadget *gadget, int intf_id);
> int (*set_remote_wakeup)(struct usb_gadget *, int set);
> int (*set_selfpowered) (struct usb_gadget *, int is_selfpowered);
> int (*vbus_session) (struct usb_gadget *, int is_active);
> --
> 2.7.4
>
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Thanks,
Thinh
next prev parent reply other threads:[~2023-03-10 23:18 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-03-09 20:24 [PATCH v7 0/5] Add function suspend/resume and remote " Elson Roy Serrao
2023-03-09 20:24 ` [PATCH v7 1/5] usb: gadget: Properly configure the device for remote wakeup Elson Roy Serrao
2023-03-09 20:24 ` [PATCH v7 2/5] usb: dwc3: Add remote wakeup handling Elson Roy Serrao
2023-03-10 23:21 ` Thinh Nguyen
2023-03-09 20:24 ` [PATCH v7 3/5] usb: gadget: Add function wakeup support Elson Roy Serrao
2023-03-10 23:17 ` Thinh Nguyen [this message]
2023-03-09 20:24 ` [PATCH v7 4/5] usb: dwc3: Add function suspend and " Elson Roy Serrao
2023-03-09 20:24 ` [PATCH v7 5/5] usb: gadget: f_ecm: Add suspend/resume and remote " Elson Roy Serrao
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230310231723.toshpghfenuymjnd@synopsys.com \
--to=thinh.nguyen@synopsys.com \
--cc=balbi@kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=quic_eserrao@quicinc.com \
--cc=quic_jackp@quicinc.com \
--cc=quic_wcheng@quicinc.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®