From: Apurva Nandan <a-nandan@ti.com>
To: Nishanth Menon <nm@ti.com>, Vignesh Raghavendra <vigneshr@ti.com>,
Tero Kristo <kristo@kernel.org>, Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
<linux-arm-kernel@lists.infradead.org>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>
Cc: Apurva Nandan <a-nandan@ti.com>
Subject: [PATCH] arm64: dts: ti: k3-j784s4-evm: Add OSPI0 flash support
Date: Mon, 27 Mar 2023 13:59:24 +0530 [thread overview]
Message-ID: <20230327082924.12427-1-a-nandan@ti.com> (raw)
Add support for OSPI flash connected to OSPI0 instance through FSS.
Also enumerate OSPI1 instance in MCU DTSI.
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
---
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 44 +++++++++++++++++++
.../boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi | 43 ++++++++++++++++++
2 files changed, 87 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
index 8cd4a7ecc121..7480f37e89e8 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
@@ -138,6 +138,24 @@ vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
J784S4_IOPAD(0x020, PIN_INPUT, 7) /* (AJ35) MCAN15_RX.GPIO0_8 */
>;
};
+
+ mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
+ pinctrl-single,pins = <
+ J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (E32) MCU_OSPI0_CLK */
+ J784S4_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (A32) MCU_OSPI0_CSn0 */
+ J784S4_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (B33) MCU_OSPI0_D0 */
+ J784S4_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (B32) MCU_OSPI0_D1 */
+ J784S4_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (C33) MCU_OSPI0_D2 */
+ J784S4_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (C35) MCU_OSPI0_D3 */
+ J784S4_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (D33) MCU_OSPI0_D4 */
+ J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (D34) MCU_OSPI0_D5 */
+ J784S4_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (E34) MCU_OSPI0_D6 */
+ J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (E33) MCU_OSPI0_D7 */
+ J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */
+ J784S4_WKUP_IOPAD(0x03c, PIN_OUTPUT, 6) /* (C32) MCU_OSPI0_CSn3.MCU_OSPI0_ECC_FAIL */
+ J784S4_WKUP_IOPAD(0x038, PIN_OUTPUT, 6) /* (B34) MCU_OSPI0_CSn2.MCU_OSPI0_RESET_OUT0 */
+ >;
+ };
};
&main_uart8 {
@@ -146,6 +164,32 @@ &main_uart8 {
pinctrl-0 = <&main_uart8_pins_default>;
};
+&fss {
+ status = "okay";
+};
+
+&ospi0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ spi-tx-bus-width = <8>;
+ spi-rx-bus-width = <8>;
+ spi-max-frequency = <25000000>;
+ cdns,tshsl-ns = <60>;
+ cdns,tsd2d-ns = <60>;
+ cdns,tchsh-ns = <60>;
+ cdns,tslch-ns = <60>;
+ cdns,read-delay = <4>;
+ cdns,phy-mode;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+};
+
&main_i2c0 {
status = "okay";
pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
index 93952af618f6..b29b95a532f6 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
@@ -308,4 +308,47 @@ cpts@3d000 {
ti,cpts-periodic-outputs = <2>;
};
};
+
+ fss: syscon@47000000 {
+ compatible = "syscon", "simple-mfd";
+ reg = <0x00 0x47000000 0x00 0x100>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ status = "disabled";
+
+ ospi0: spi@47040000 {
+ compatible = "ti,am654-ospi", "cdns,qspi-nor";
+ reg = <0x00 0x47040000 0x00 0x100>,
+ <0x5 0x0000000 0x1 0x0000000>;
+ interrupts = <GIC_SPI 840 IRQ_TYPE_LEVEL_HIGH>;
+ cdns,fifo-depth = <256>;
+ cdns,fifo-width = <4>;
+ cdns,trigger-address = <0x0>;
+ clocks = <&k3_clks 161 7>;
+ assigned-clocks = <&k3_clks 161 7>;
+ assigned-clock-parents = <&k3_clks 161 9>;
+ assigned-clock-rates = <166666666>;
+ power-domains = <&k3_pds 161 TI_SCI_PD_EXCLUSIVE>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ ospi1: spi@47050000 {
+ compatible = "ti,am654-ospi", "cdns,qspi-nor";
+ reg = <0x00 0x47050000 0x00 0x100>,
+ <0x7 0x0000000 0x1 0x0000000>;
+ interrupts = <GIC_SPI 841 IRQ_TYPE_LEVEL_HIGH>;
+ cdns,fifo-depth = <256>;
+ cdns,fifo-width = <4>;
+ cdns,trigger-address = <0x0>;
+ clocks = <&k3_clks 162 7>;
+ power-domains = <&k3_pds 162 TI_SCI_PD_EXCLUSIVE>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+ };
+
};
--
2.34.1
next reply other threads:[~2023-03-27 9:54 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-03-27 8:29 Apurva Nandan [this message]
2023-03-27 8:55 ` Krzysztof Kozlowski
2023-03-27 8:57 ` Raghavendra, Vignesh
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230327082924.12427-1-a-nandan@ti.com \
--to=a-nandan@ti.com \
--cc=devicetree@vger.kernel.org \
--cc=kristo@kernel.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=nm@ti.com \
--cc=robh+dt@kernel.org \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®