mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Jan Kara <jack@suse.cz>
To: Baokun Li <libaokun1@huawei.com>
Cc: linux-ext4@vger.kernel.org, tytso@mit.edu,
	adilger.kernel@dilger.ca, jack@suse.cz, ritesh.list@gmail.com,
	linux-kernel@vger.kernel.org, yi.zhang@huawei.com,
	yangerkun@huawei.com, yukuai3@huawei.com
Subject: Re: [PATCH v2 1/2] ext4: only update i_reserved_data_blocks on successful block allocation
Date: Tue, 11 Apr 2023 11:08:00 +0200	[thread overview]
Message-ID: <20230411090800.rrsvbab3tio7rs2m@quack3> (raw)
In-Reply-To: <20230406132834.1669710-2-libaokun1@huawei.com>

On Thu 06-04-23 21:28:33, Baokun Li wrote:
> In our fault injection test, we create an ext4 file, migrate it to
> non-extent based file, then punch a hole and finally trigger a WARN_ON
> in the ext4_da_update_reserve_space():
> 
> EXT4-fs warning (device sda): ext4_da_update_reserve_space:369:
> ino 14, used 11 with only 10 reserved data blocks
> 
> When writing back a non-extent based file, if we enable delalloc, the
> number of reserved blocks will be subtracted from the number of blocks
> mapped by ext4_ind_map_blocks(), and the extent status tree will be
> updated. We update the extent status tree by first removing the old
> extent_status and then inserting the new extent_status. If the block range
> we remove happens to be in an extent, then we need to allocate another
> extent_status with ext4_es_alloc_extent().
> 
>        use old    to remove   to add new
>     |----------|------------|------------|
>               old extent_status
> 
> The problem is that the allocation of a new extent_status failed due to a
> fault injection, and __es_shrink() did not get free memory, resulting in
> a return of -ENOMEM. Then do_writepages() retries after receiving -ENOMEM,
> we map to the same extent again, and the number of reserved blocks is again
> subtracted from the number of blocks in that extent. Since the blocks in
> the same extent are subtracted twice, we end up triggering WARN_ON at
> ext4_da_update_reserve_space() because used > ei->i_reserved_data_blocks.
> 
> For non-extent based file, we update the number of reserved blocks after
> ext4_ind_map_blocks() is executed, which causes a problem that when we call
> ext4_ind_map_blocks() to create a block, it doesn't always create a block,
> but we always reduce the number of reserved blocks. So we move the logic
> for updating reserved blocks to ext4_ind_map_blocks() to ensure that the
> number of reserved blocks is updated only after we do succeed in allocating
> some new blocks.
> 
> Fixes: 5f634d064c70 ("ext4: Fix quota accounting error with fallocate")
> Signed-off-by: Baokun Li <libaokun1@huawei.com>

Looks good, just one nit below.

> diff --git a/fs/ext4/indirect.c b/fs/ext4/indirect.c
> index c68bebe7ff4b..9acab70ddf5e 100644
> --- a/fs/ext4/indirect.c
> +++ b/fs/ext4/indirect.c
> @@ -651,6 +651,14 @@ int ext4_ind_map_blocks(handle_t *handle, struct inode *inode,
>  
>  	ext4_update_inode_fsync_trans(handle, inode, 1);
>  	count = ar.len;
> +
> +	/*
> +	 * Update reserved blocks/metadata blocks after successful block
> +	 * allocation which had been deferred till now.
> +	 */
> +	if ((count > 0) && (flags & EXT4_GET_BLOCKS_DELALLOC_RESERVE))

You don't need the count > 0 condition here. It should be always true.

								Honza

-- 
Jan Kara <jack@suse.com>
SUSE Labs, CR

  reply	other threads:[~2023-04-11  9:09 UTC|newest]

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-04-06 13:28 [PATCH v2 0/2] ext4: fix WARNING in ext4_da_update_reserve_space Baokun Li
2023-04-06 13:28 ` [PATCH v2 1/2] ext4: only update i_reserved_data_blocks on successful block allocation Baokun Li
2023-04-11  9:08   ` Jan Kara [this message]
2023-04-11 14:10     ` Baokun Li
2023-04-06 13:28 ` [PATCH v2 2/2] ext4: use __GFP_NOFAIL if allocating extents_status cannot fail Baokun Li
2023-04-11  9:19   ` Jan Kara
2023-04-11 14:04     ` Baokun Li

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20230411090800.rrsvbab3tio7rs2m@quack3 \
    --to=jack@suse.cz \
    --cc=adilger.kernel@dilger.ca \
    --cc=libaokun1@huawei.com \
    --cc=linux-ext4@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=ritesh.list@gmail.com \
    --cc=tytso@mit.edu \
    --cc=yangerkun@huawei.com \
    --cc=yi.zhang@huawei.com \
    --cc=yukuai3@huawei.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®