mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Oleksij Rempel <o.rempel@pengutronix.de>
To: "David S. Miller" <davem@davemloft.net>,
	Andrew Lunn <andrew@lunn.ch>, Eric Dumazet <edumazet@google.com>,
	Florian Fainelli <f.fainelli@gmail.com>,
	Jakub Kicinski <kuba@kernel.org>, Paolo Abeni <pabeni@redhat.com>,
	Vladimir Oltean <olteanv@gmail.com>,
	Woojung Huh <woojung.huh@microchip.com>,
	Arun Ramadoss <arun.ramadoss@microchip.com>,
	"Russell King (Oracle)" <linux@armlinux.org.uk>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>,
	kernel@pengutronix.de, linux-kernel@vger.kernel.org,
	netdev@vger.kernel.org, UNGLinuxDriver@microchip.com
Subject: [PATCH net-next v3 1/2] net: dsa: microchip: ksz8: Make flow control, speed, and duplex on CPU port configurable
Date: Thu, 18 May 2023 11:29:12 +0200	[thread overview]
Message-ID: <20230518092913.977705-2-o.rempel@pengutronix.de> (raw)
In-Reply-To: <20230518092913.977705-1-o.rempel@pengutronix.de>

Allow flow control, speed, and duplex settings on the CPU port to be
configurable. Previously, the speed and duplex relied on default switch
values, which limited flexibility. Additionally, flow control was
hardcoded and only functional in duplex mode. This update enhances the
configurability of these parameters.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 drivers/net/dsa/microchip/ksz8.h       |  4 ++
 drivers/net/dsa/microchip/ksz8795.c    | 51 +++++++++++++++++++++++++-
 drivers/net/dsa/microchip/ksz_common.c |  1 +
 3 files changed, 54 insertions(+), 2 deletions(-)

diff --git a/drivers/net/dsa/microchip/ksz8.h b/drivers/net/dsa/microchip/ksz8.h
index e68465fdf6b9..ec02baca726f 100644
--- a/drivers/net/dsa/microchip/ksz8.h
+++ b/drivers/net/dsa/microchip/ksz8.h
@@ -58,5 +58,9 @@ int ksz8_switch_detect(struct ksz_device *dev);
 int ksz8_switch_init(struct ksz_device *dev);
 void ksz8_switch_exit(struct ksz_device *dev);
 int ksz8_change_mtu(struct ksz_device *dev, int port, int mtu);
+void ksz8_phylink_mac_link_up(struct ksz_device *dev, int port,
+			      unsigned int mode, phy_interface_t interface,
+			      struct phy_device *phydev, int speed, int duplex,
+			      bool tx_pause, bool rx_pause);
 
 #endif
diff --git a/drivers/net/dsa/microchip/ksz8795.c b/drivers/net/dsa/microchip/ksz8795.c
index f56fca1b1a22..9cfe343d2214 100644
--- a/drivers/net/dsa/microchip/ksz8795.c
+++ b/drivers/net/dsa/microchip/ksz8795.c
@@ -1371,6 +1371,55 @@ void ksz8_config_cpu_port(struct dsa_switch *ds)
 	}
 }
 
+/**
+ * ksz8_upstream_link_up - Configures the CPU/upstream port of the switch.
+ * @dev: The KSZ device instance.
+ * @port: The port number to configure.
+ * @speed: The desired link speed.
+ * @duplex: The desired duplex mode.
+ * @tx_pause: If true, enables transmit pause.
+ * @rx_pause: If true, enables receive pause.
+ *
+ * Description:
+ * The function configures flow control and speed settings for the CPU/upstream
+ * port of the switch based on the desired settings, current duplex mode, and
+ * speed.
+ */
+static void ksz8_upstream_link_up(struct ksz_device *dev, int port, int speed,
+				 int duplex, bool tx_pause, bool rx_pause)
+{
+	u8 ctrl = 0;
+
+	/* SW_FLOW_CTRL, SW_HALF_DUPLEX, and SW_10_MBIT bits are bootstrappable.
+	 * They can have different values depending on your board setup.
+	 */
+	if (duplex) {
+		if (tx_pause || rx_pause)
+			ctrl |= SW_FLOW_CTRL;
+	} else {
+		ctrl |= SW_HALF_DUPLEX;
+	}
+
+	/* This hardware only supports SPEED_10 and SPEED_100. For SPEED_10
+	 * we need to set the SW_10_MBIT bit. Otherwise, we can leave it 0.
+	 */
+	if (speed == SPEED_10)
+		ctrl |= SW_10_MBIT;
+
+	ksz_rmw8(dev, REG_SW_CTRL_4, SW_HALF_DUPLEX | SW_FLOW_CTRL |
+		 SW_10_MBIT, ctrl);
+}
+
+void ksz8_phylink_mac_link_up(struct ksz_device *dev, int port,
+			      unsigned int mode, phy_interface_t interface,
+			      struct phy_device *phydev, int speed, int duplex,
+			      bool tx_pause, bool rx_pause)
+{
+	if (dsa_is_upstream_port(dev->ds, port))
+		ksz8_upstream_link_up(dev, port, speed, duplex, tx_pause,
+				     rx_pause);
+}
+
 static int ksz8_handle_global_errata(struct dsa_switch *ds)
 {
 	struct ksz_device *dev = ds->priv;
@@ -1419,8 +1468,6 @@ int ksz8_setup(struct dsa_switch *ds)
 	 */
 	ds->vlan_filtering_is_global = true;
 
-	ksz_cfg(dev, S_REPLACE_VID_CTRL, SW_FLOW_CTRL, true);
-
 	/* Enable automatic fast aging when link changed detected. */
 	ksz_cfg(dev, S_LINK_AGING_CTRL, SW_LINK_AUTO_AGING, true);
 
diff --git a/drivers/net/dsa/microchip/ksz_common.c b/drivers/net/dsa/microchip/ksz_common.c
index a4428be5f483..6e19ad70c671 100644
--- a/drivers/net/dsa/microchip/ksz_common.c
+++ b/drivers/net/dsa/microchip/ksz_common.c
@@ -210,6 +210,7 @@ static const struct ksz_dev_ops ksz8_dev_ops = {
 	.mirror_add = ksz8_port_mirror_add,
 	.mirror_del = ksz8_port_mirror_del,
 	.get_caps = ksz8_get_caps,
+	.phylink_mac_link_up = ksz8_phylink_mac_link_up,
 	.config_cpu_port = ksz8_config_cpu_port,
 	.enable_stp_addr = ksz8_enable_stp_addr,
 	.reset = ksz8_reset_switch,
-- 
2.39.2


  reply	other threads:[~2023-05-18  9:29 UTC|newest]

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-05-18  9:29 [PATCH net-next v3 0/2] Fine-Tune Flow Control and Speed Configurations in Microchip KSZ8xxx DSA Driver Oleksij Rempel
2023-05-18  9:29 ` Oleksij Rempel [this message]
2023-05-19  9:01   ` [PATCH net-next v3 1/2] net: dsa: microchip: ksz8: Make flow control, speed, and duplex on CPU port configurable Simon Horman
2023-05-19  9:21   ` Vladimir Oltean
2023-05-18  9:29 ` [PATCH net-next v3 2/2] net: dsa: microchip: ksz8: Add function to configure downstream ports for KSZ8xxx Oleksij Rempel
2023-05-19  9:03   ` Simon Horman
2023-05-18  9:32 ` [PATCH net-next v3 0/2] Fine-Tune Flow Control and Speed Configurations in Microchip KSZ8xxx DSA Driver Marc Kleine-Budde

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20230518092913.977705-2-o.rempel@pengutronix.de \
    --to=o.rempel@pengutronix.de \
    --cc=UNGLinuxDriver@microchip.com \
    --cc=andrew@lunn.ch \
    --cc=arun.ramadoss@microchip.com \
    --cc=davem@davemloft.net \
    --cc=edumazet@google.com \
    --cc=f.fainelli@gmail.com \
    --cc=kernel@pengutronix.de \
    --cc=kuba@kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux@armlinux.org.uk \
    --cc=netdev@vger.kernel.org \
    --cc=olteanv@gmail.com \
    --cc=pabeni@redhat.com \
    --cc=woojung.huh@microchip.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®