mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: MD Danish Anwar <danishanwar@ti.com>
To: Andrew Lunn <andrew@lunn.ch>, Roger Quadros <rogerq@ti.com>,
	MD Danish Anwar <danishanwar@ti.com>,
	Conor Dooley <conor+dt@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	Rob Herring <robh+dt@kernel.org>, Paolo Abeni <pabeni@redhat.com>,
	Jakub Kicinski <kuba@kernel.org>,
	Eric Dumazet <edumazet@google.com>,
	"David S. Miller" <davem@davemloft.net>,
	Vignesh Raghavendra <vigneshr@ti.com>,
	Simon Horman <horms@kernel.org>
Cc: <linux-kernel@vger.kernel.org>, <devicetree@vger.kernel.org>,
	<netdev@vger.kernel.org>, <srk@ti.com>, <r-gunasekaran@ti.com>,
	Roger Quadros <rogerq@kernel.org>
Subject: [PATCH net-next v3 2/2] net: ti: icssg-prueth: Add support for half duplex operation
Date: Wed, 13 Sep 2023 14:40:11 +0530	[thread overview]
Message-ID: <20230913091011.2808202-3-danishanwar@ti.com> (raw)
In-Reply-To: <20230913091011.2808202-1-danishanwar@ti.com>

This patch adds support for half duplex operation at 10M and 100M link
speeds for AM654x/AM64x devices.
- Driver configures rand_seed, a random number, in DMEM HD_RAND_SEED_OFFSET
field, which will be used by firmware for Back off time calculation.
- Driver informs FW about half duplex link operation in DMEM
PORT_LINK_SPEED_OFFSET field by setting bit 7 for 10/100M HD.

Hence, the half duplex operation depends on board design the
"ti,half-duplex-capable" property has to be enabled for ICSS-G ports if HW
is capable to perform half duplex.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
---
 drivers/net/ethernet/ti/icssg/icssg_config.c | 14 ++++++++++++++
 drivers/net/ethernet/ti/icssg/icssg_prueth.c | 17 +++++++++++++++--
 drivers/net/ethernet/ti/icssg/icssg_prueth.h |  2 ++
 3 files changed, 31 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/ti/icssg/icssg_config.c b/drivers/net/ethernet/ti/icssg/icssg_config.c
index 933b84666574..c1da70f247d4 100644
--- a/drivers/net/ethernet/ti/icssg/icssg_config.c
+++ b/drivers/net/ethernet/ti/icssg/icssg_config.c
@@ -433,6 +433,17 @@ int emac_set_port_state(struct prueth_emac *emac,
 	return ret;
 }
 
+void icssg_config_half_duplex(struct prueth_emac *emac)
+{
+	u32 val;
+
+	if (!emac->half_duplex)
+		return;
+
+	val = get_random_u32();
+	writel(val, emac->dram.va + HD_RAND_SEED_OFFSET);
+}
+
 void icssg_config_set_speed(struct prueth_emac *emac)
 {
 	u8 fw_speed;
@@ -453,5 +464,8 @@ void icssg_config_set_speed(struct prueth_emac *emac)
 		return;
 	}
 
+	if (emac->duplex == DUPLEX_HALF)
+		fw_speed |= FW_LINK_SPEED_HD;
+
 	writeb(fw_speed, emac->dram.va + PORT_LINK_SPEED_OFFSET);
 }
diff --git a/drivers/net/ethernet/ti/icssg/icssg_prueth.c b/drivers/net/ethernet/ti/icssg/icssg_prueth.c
index 92b13057d4de..6635b28bc672 100644
--- a/drivers/net/ethernet/ti/icssg/icssg_prueth.c
+++ b/drivers/net/ethernet/ti/icssg/icssg_prueth.c
@@ -1029,6 +1029,8 @@ static void emac_adjust_link(struct net_device *ndev)
 		 * values
 		 */
 		if (emac->link) {
+			if (emac->duplex == DUPLEX_HALF)
+				icssg_config_half_duplex(emac);
 			/* Set the RGMII cfg for gig en and full duplex */
 			icssg_update_rgmii_cfg(prueth->miig_rt, emac);
 
@@ -1147,9 +1149,13 @@ static int emac_phy_connect(struct prueth_emac *emac)
 		return -ENODEV;
 	}
 
+	if (!emac->half_duplex) {
+		dev_dbg(prueth->dev, "half duplex mode is not supported\n");
+		phy_remove_link_mode(ndev->phydev, ETHTOOL_LINK_MODE_10baseT_Half_BIT);
+		phy_remove_link_mode(ndev->phydev, ETHTOOL_LINK_MODE_100baseT_Half_BIT);
+	}
+
 	/* remove unsupported modes */
-	phy_remove_link_mode(ndev->phydev, ETHTOOL_LINK_MODE_10baseT_Half_BIT);
-	phy_remove_link_mode(ndev->phydev, ETHTOOL_LINK_MODE_100baseT_Half_BIT);
 	phy_remove_link_mode(ndev->phydev, ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
 	phy_remove_link_mode(ndev->phydev, ETHTOOL_LINK_MODE_Pause_BIT);
 	phy_remove_link_mode(ndev->phydev, ETHTOOL_LINK_MODE_Asym_Pause_BIT);
@@ -2113,6 +2119,10 @@ static int prueth_probe(struct platform_device *pdev)
 				      eth0_node->name);
 			goto exit_iep;
 		}
+
+		if (of_find_property(eth0_node, "ti,half-duplex-capable", NULL))
+			prueth->emac[PRUETH_MAC0]->half_duplex = 1;
+
 		prueth->emac[PRUETH_MAC0]->iep = prueth->iep0;
 	}
 
@@ -2124,6 +2134,9 @@ static int prueth_probe(struct platform_device *pdev)
 			goto netdev_exit;
 		}
 
+		if (of_find_property(eth1_node, "ti,half-duplex-capable", NULL))
+			prueth->emac[PRUETH_MAC1]->half_duplex = 1;
+
 		prueth->emac[PRUETH_MAC1]->iep = prueth->iep0;
 	}
 
diff --git a/drivers/net/ethernet/ti/icssg/icssg_prueth.h b/drivers/net/ethernet/ti/icssg/icssg_prueth.h
index 3fe80a8758d3..8b6d6b497010 100644
--- a/drivers/net/ethernet/ti/icssg/icssg_prueth.h
+++ b/drivers/net/ethernet/ti/icssg/icssg_prueth.h
@@ -145,6 +145,7 @@ struct prueth_emac {
 	struct icss_iep *iep;
 	unsigned int rx_ts_enabled : 1;
 	unsigned int tx_ts_enabled : 1;
+	unsigned int half_duplex : 1;
 
 	/* DMA related */
 	struct prueth_tx_chn tx_chns[PRUETH_MAX_TX_QUEUES];
@@ -271,6 +272,7 @@ int icssg_config(struct prueth *prueth, struct prueth_emac *emac,
 int emac_set_port_state(struct prueth_emac *emac,
 			enum icssg_port_state_cmd state);
 void icssg_config_set_speed(struct prueth_emac *emac);
+void icssg_config_half_duplex(struct prueth_emac *emac);
 
 /* Buffer queue helpers */
 int icssg_queue_pop(struct prueth *prueth, u8 queue);
-- 
2.34.1


  parent reply	other threads:[~2023-09-13  9:10 UTC|newest]

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-09-13  9:10 [PATCH net-next v3 0/2] Add Half Duplex support for ICSSG Driver MD Danish Anwar
2023-09-13  9:10 ` [PATCH net-next v3 1/2] dt-bindings: net: Add documentation for Half duplex support MD Danish Anwar
2023-09-13 12:21   ` Andrew Lunn
2023-09-13 14:30   ` Conor Dooley
2023-09-14 14:29   ` Rob Herring
2023-09-13  9:10 ` MD Danish Anwar [this message]
2023-09-15 13:00 ` [PATCH net-next v3 0/2] Add Half Duplex support for ICSSG Driver patchwork-bot+netdevbpf

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20230913091011.2808202-3-danishanwar@ti.com \
    --to=danishanwar@ti.com \
    --cc=andrew@lunn.ch \
    --cc=conor+dt@kernel.org \
    --cc=davem@davemloft.net \
    --cc=devicetree@vger.kernel.org \
    --cc=edumazet@google.com \
    --cc=horms@kernel.org \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=kuba@kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=netdev@vger.kernel.org \
    --cc=pabeni@redhat.com \
    --cc=r-gunasekaran@ti.com \
    --cc=robh+dt@kernel.org \
    --cc=rogerq@kernel.org \
    --cc=rogerq@ti.com \
    --cc=srk@ti.com \
    --cc=vigneshr@ti.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®