[PATCH net-next v2 08/10] dt-bindings: net: dsa: marvell: convert to json-schema

["Arınç ÜNAL" <arinc.unal@arinc9.com>]

Convert the document for Marvell ethernet switches to json-schema.

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
---
 .../devicetree/bindings/net/dsa/marvell.txt   | 109 ----------
 .../devicetree/bindings/net/dsa/marvell.yaml  | 204 ++++++++++++++++++
 2 files changed, 204 insertions(+), 109 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/net/dsa/marvell.txt
 create mode 100644 Documentation/devicetree/bindings/net/dsa/marvell.yaml

diff --git a/Documentation/devicetree/bindings/net/dsa/marvell.txt b/Documentation/devicetree/bindings/net/dsa/marvell.txt
deleted file mode 100644
index 6ec0c181b6db..000000000000
--- a/Documentation/devicetree/bindings/net/dsa/marvell.txt
+++ /dev/null
@@ -1,109 +0,0 @@
-Marvell DSA Switch Device Tree Bindings
----------------------------------------
-
-WARNING: This binding is currently unstable. Do not program it into a
-FLASH never to be changed again. Once this binding is stable, this
-warning will be removed.
-
-If you need a stable binding, use the old dsa.txt binding.
-
-Marvell Switches are MDIO devices. The following properties should be
-placed as a child node of an mdio device.
-
-The properties described here are those specific to Marvell devices.
-Additional required and optional properties can be found in dsa.txt.
-
-The compatibility string is used only to find an identification register,
-which is at a different MDIO base address in different switch families.
-- "marvell,mv88e6085"	: Switch has base address 0x10. Use with models:
-			  6085, 6095, 6097, 6123, 6131, 6141, 6161, 6165,
-			  6171, 6172, 6175, 6176, 6185, 6240, 6320, 6321,
-			  6341, 6350, 6351, 6352
-- "marvell,mv88e6190"	: Switch has base address 0x00. Use with models:
-			  6190, 6190X, 6191, 6290, 6361, 6390, 6390X
-- "marvell,mv88e6250"	: Switch has base address 0x08 or 0x18. Use with model:
-			  6220, 6250
-
-Required properties:
-- compatible		: Should be one of "marvell,mv88e6085",
-			  "marvell,mv88e6190" or "marvell,mv88e6250" as
-			  indicated above
-- reg			: Address on the MII bus for the switch.
-
-Optional properties:
-
-- reset-gpios		: Should be a gpio specifier for a reset line
-- interrupts		: Interrupt from the switch
-- interrupt-controller	: Indicates the switch is itself an interrupt
-			  controller. This is used for the PHY interrupts.
-#interrupt-cells = <2>	: Controller uses two cells, number and flag
-- eeprom-length		: Set to the length of an EEPROM connected to the
-			  switch. Must be set if the switch can not detect
-			  the presence and/or size of a connected EEPROM,
-			  otherwise optional.
-- mdio			: Container of PHY and devices on the switches MDIO
-			  bus.
-- mdio?		: Container of PHYs and devices on the external MDIO
-			  bus. The node must contains a compatible string of
-			  "marvell,mv88e6xxx-mdio-external"
-
-Example:
-
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		interrupt-parent = <&gpio0>;
-		interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-
-		switch0: switch@0 {
-			compatible = "marvell,mv88e6085";
-			reg = <0>;
-			reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
-
-			mdio {
-				#address-cells = <1>;
-				#size-cells = <0>;
-				switch1phy0: switch1phy0@0 {
-					reg = <0>;
-					interrupt-parent = <&switch0>;
-					interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
-				};
-			};
-		};
-	};
-
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		interrupt-parent = <&gpio0>;
-		interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-
-		switch0: switch@0 {
-			compatible = "marvell,mv88e6190";
-			reg = <0>;
-			reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
-
-			mdio {
-				#address-cells = <1>;
-				#size-cells = <0>;
-				switch1phy0: switch1phy0@0 {
-					reg = <0>;
-					interrupt-parent = <&switch0>;
-					interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
-				};
-			};
-
-			mdio1 {
-				compatible = "marvell,mv88e6xxx-mdio-external";
-				#address-cells = <1>;
-				#size-cells = <0>;
-				switch1phy9: switch1phy0@9 {
-					reg = <9>;
-				};
-			};
-		};
-	};
diff --git a/Documentation/devicetree/bindings/net/dsa/marvell.yaml b/Documentation/devicetree/bindings/net/dsa/marvell.yaml
new file mode 100644
index 000000000000..45756b8d74d9
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/marvell.yaml
@@ -0,0 +1,204 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/dsa/marvell.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Marvell Ethernet Switches
+
+$ref: dsa.yaml#/$defs/ethernet-ports
+
+maintainers:
+  - Andrew Lunn <andrew@lunn.ch>
+  - Arınç ÜNAL <arinc.unal@arinc9.com>
+
+description:
+  Marvell ethernet switches are MDIO devices.
+
+properties:
+  compatible:
+    oneOf:
+      - description: |
+          Switch has base address 0x10. Use with models:
+          6085, 6095, 6097, 6123, 6131, 6141, 6161, 6165, 6171, 6172, 6175,
+          6176, 6185, 6240, 6320, 6321, 6341, 6350, 6351, 6352
+        const: marvell,mv88e6085
+
+      - description: |
+          Switch has base address 0x00. Use with models:
+          6190, 6190X, 6191, 6290, 6361, 6390, 6390X
+        const: marvell,mv88e6190
+
+      - description: |
+          Switch has base address 0x08 or 0x18. Use with models:
+          6220, 6250
+        const: marvell,mv88e6250
+
+  reg:
+    maxItems: 1
+
+  reset-gpios:
+    description: GPIO to be used to reset the whole device
+    maxItems: 1
+
+  "#interrupt-cells":
+    const: 2
+
+  interrupt-controller: true
+
+  interrupts:
+    maxItems: 1
+
+  eeprom-length:
+    description:
+      Set to the length of an EEPROM connected to the switch. Must be set if the
+      switch can not detect the presence and/or size of a connected EEPROM,
+      otherwise optional.
+
+  mdio:
+    description:
+      The optional node for the MDIO bus of the switch. The bus will be
+      registered non-OF-based if this is not defined.
+    $ref: /schemas/net/mdio.yaml#
+
+  mdio-external:
+    description: The externally reachable MDIO bus of the 6390 family switches
+    $ref: /schemas/net/mdio.yaml#
+
+    properties:
+      compatible:
+        const: marvell,mv88e6xxx-mdio-external
+
+    required:
+      - compatible
+
+required:
+  - compatible
+  - reg
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          enum:
+            - marvell,mv88e6085
+            - marvell,mv88e6250
+    then:
+      properties:
+        mdio-external: false
+
+  - if:
+      required: [ mdio ]
+    then:
+      patternProperties:
+        "^(ethernet-)?ports$":
+          patternProperties:
+            "^(ethernet-)?port@[0-9]+$":
+              $ref: /schemas/net/ethernet-controller.yaml#/$defs/phylink
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    mdio {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        switch@0 {
+            compatible = "marvell,mv88e6085";
+            reg = <0>;
+            reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
+
+            ethernet-ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;
+                    phy-mode = "rmii";
+                    ethernet = <&fec1>;
+
+                    fixed-link {
+                        speed = <100>;
+                        full-duplex;
+                    };
+                };
+
+                port@1 {
+                    reg = <1>;
+                    label = "swp1";
+                };
+            };
+        };
+    };
+
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    mdio {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        switch: switch@0 {
+            compatible = "marvell,mv88e6190";
+            reg = <0>;
+            reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
+            interrupt-parent = <&gpio3>;
+            interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+            interrupt-controller;
+            #interrupt-cells = <2>;
+
+            ethernet-ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;
+                    phy-mode = "rmii";
+                    ethernet = <&fec1>;
+
+                    fixed-link {
+                        speed = <100>;
+                        full-duplex;
+                    };
+                };
+
+                port@1 {
+                    reg = <1>;
+                    label = "swp1";
+                    phy-handle = <&ethphy1>;
+                };
+
+                port@2 {
+                    reg = <2>;
+                    label = "swp2";
+                    phy-handle = <&ext_ethphy0>;
+                };
+            };
+
+            mdio {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                ethphy1: ethernet-phy@1 {
+                    reg = <1>;
+                    interrupt-parent = <&switch>;
+                    interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
+                };
+            };
+
+            mdio-external {
+                compatible = "marvell,mv88e6xxx-mdio-external";
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                ext_ethphy0: ethernet-phy@0 {
+                    reg = <0>;
+                    compatible = "ethernet-phy-ieee802.3-c45";
+                };
+            };
+        };
+    };
-- 
2.39.2