From: Jai Luthra <j-luthra@ti.com>
To: Catalin Marinas <catalin.marinas@arm.com>,
Will Deacon <will@kernel.org>, Nishanth Menon <nm@ti.com>,
Vignesh Raghavendra <vigneshr@ti.com>,
Tero Kristo <kristo@kernel.org>, Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Conor Dooley <conor+dt@kernel.org>
Cc: <linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>, <devicetree@vger.kernel.org>,
Aradhya Bhatia <a-bhatia1@ti.com>,
Devarsh Thakkar <devarsht@ti.com>,
Vaishnav Achath <vaishnav.a@ti.com>,
Julien Massot <julien.massot@collabora.com>,
Martyn Welch <martyn.welch@collabora.com>,
Matthias Schiffer <matthias.schiffer@ew.tq-group.com>,
Jai Luthra <j-luthra@ti.com>
Subject: [PATCH v3 6/9] arm64: dts: ti: k3-am62x: Add overlays for OV5640
Date: Tue, 28 Nov 2023 15:39:48 +0530 [thread overview]
Message-ID: <20231128-csi_dts-v3-6-0bb11cfa9d43@ti.com> (raw)
In-Reply-To: <20231128-csi_dts-v3-0-0bb11cfa9d43@ti.com>
Three different OV5640 modules are supported using the 15-pin FFC
connector on SK-AM62:
- Digilent PCam 5C
- ALINX AN5641
- TEVI-OV5640-*-RPI
The Digilent and ALINX modules supply a 12Mhz XCLK to the sensor, while
the TEVI module supplies a 24Mhz XCLK, thus requiring a separate
overlay.
These overlays can be used on other boards of the SK-AM62* family that
have a 15/22-pin FFC connector, so we name the overlays with the prefix
k3-am62x-.
Tested-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
---
arch/arm64/boot/dts/ti/Makefile | 19 ++++-
.../arm64/boot/dts/ti/k3-am62x-sk-csi2-ov5640.dtso | 82 ++++++++++++++++++++++
.../boot/dts/ti/k3-am62x-sk-csi2-tevi-ov5640.dtso | 82 ++++++++++++++++++++++
3 files changed, 182 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index c6c7825b4cb2..f957b5f741ff 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -32,6 +32,10 @@ dtb-$(CONFIG_ARCH_K3) += k3-am62a7-sk.dtb
# Boards with AM62Px SoC
dtb-$(CONFIG_ARCH_K3) += k3-am62p5-sk.dtb
+# Common overlays for SK-AM62* family of boards
+dtb-$(CONFIG_ARCH_K3) += k3-am62x-sk-csi2-ov5640.dtbo
+dtb-$(CONFIG_ARCH_K3) += k3-am62x-sk-csi2-tevi-ov5640.dtbo
+
# Boards with AM64x SoC
dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am642-phyboard-electra-rdk.dtb
@@ -87,13 +91,26 @@ k3-am625-beagleplay-csi2-ov5640-dtbs := k3-am625-beagleplay.dtb \
k3-am625-beagleplay-csi2-ov5640.dtbo
k3-am625-beagleplay-csi2-tevi-ov5640-dtbs := k3-am625-beagleplay.dtb \
k3-am625-beagleplay-csi2-tevi-ov5640.dtbo
+k3-am625-sk-csi2-ov5640-dtbs := k3-am625-sk.dtb \
+ k3-am62x-sk-csi2-ov5640.dtbo
+k3-am625-sk-csi2-tevi-ov5640-dtbs := k3-am625-sk.dtb \
+ k3-am62x-sk-csi2-tevi-ov5640.dtbo
+k3-am62a7-sk-csi2-ov5640-dtbs := k3-am62a7-sk.dtb \
+ k3-am62x-sk-csi2-ov5640.dtbo
+k3-am62a7-sk-csi2-tevi-ov5640-dtbs := k3-am62a7-sk.dtb \
+ k3-am62x-sk-csi2-tevi-ov5640.dtbo
dtb- += k3-am625-beagleplay-csi2-ov5640.dtb \
- k3-am625-beagleplay-csi2-tevi-ov5640.dtb
+ k3-am625-beagleplay-csi2-tevi-ov5640.dtb \
+ k3-am625-sk-csi2-ov5640.dtb \
+ k3-am625-sk-csi2-tevi-ov5640.dtb \
+ k3-am62a7-sk-csi2-ov5640.dtb \
+ k3-am62a7-sk-csi2-tevi-ov5640.dtb
# Enable support for device-tree overlays
DTC_FLAGS_k3-am625-beagleplay += -@
DTC_FLAGS_k3-am625-sk += -@
DTC_FLAGS_k3-am62-lp-sk += -@
+DTC_FLAGS_k3-am62a7-sk += -@
DTC_FLAGS_k3-am6548-iot2050-advanced-m2 += -@
DTC_FLAGS_k3-j721e-common-proc-board += -@
DTC_FLAGS_k3-j721s2-common-proc-board += -@
diff --git a/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-ov5640.dtso b/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-ov5640.dtso
new file mode 100644
index 000000000000..1f3aebbc8df8
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-ov5640.dtso
@@ -0,0 +1,82 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ALINX AN5641 & Digilent PCam 5C - OV5640 camera module
+ * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+&{/} {
+ clk_ov5640_fixed: ov5640-xclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <12000000>;
+ };
+};
+
+&main_i2c2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ i2c-switch@71 {
+ compatible = "nxp,pca9543";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x71>;
+
+ /* CAM port */
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ ov5640: camera@3c {
+ compatible = "ovti,ov5640";
+ reg = <0x3c>;
+
+ clocks = <&clk_ov5640_fixed>;
+ clock-names = "xclk";
+ powerdown-gpios = <&exp1 13 GPIO_ACTIVE_LOW>;
+
+ port {
+ csi2_cam0: endpoint {
+ remote-endpoint = <&csi2rx0_in_sensor>;
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+ };
+ };
+};
+
+&cdns_csi2rx0 {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ csi0_port0: port@0 {
+ reg = <0>;
+ status = "okay";
+
+ csi2rx0_in_sensor: endpoint {
+ remote-endpoint = <&csi2_cam0>;
+ bus-type = <4>; /* CSI2 DPHY. */
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+};
+
+&ti_csi2rx0 {
+ status = "okay";
+};
+
+&dphy0 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-tevi-ov5640.dtso b/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-tevi-ov5640.dtso
new file mode 100644
index 000000000000..6a367f13be63
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-tevi-ov5640.dtso
@@ -0,0 +1,82 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Technexion TEVI-OV5640-*-RPI - OV5640 camera module
+ * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+&{/} {
+ clk_ov5640_fixed: ov5640-xclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24000000>;
+ };
+};
+
+&main_i2c2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ i2c-switch@71 {
+ compatible = "nxp,pca9543";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x71>;
+
+ /* CAM port */
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ ov5640: camera@3c {
+ compatible = "ovti,ov5640";
+ reg = <0x3c>;
+
+ clocks = <&clk_ov5640_fixed>;
+ clock-names = "xclk";
+ powerdown-gpios = <&exp1 13 GPIO_ACTIVE_LOW>;
+
+ port {
+ csi2_cam0: endpoint {
+ remote-endpoint = <&csi2rx0_in_sensor>;
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+ };
+ };
+};
+
+&cdns_csi2rx0 {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ csi0_port0: port@0 {
+ reg = <0>;
+ status = "okay";
+
+ csi2rx0_in_sensor: endpoint {
+ remote-endpoint = <&csi2_cam0>;
+ bus-type = <4>; /* CSI2 DPHY. */
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+};
+
+&ti_csi2rx0 {
+ status = "okay";
+};
+
+&dphy0 {
+ status = "okay";
+};
--
2.42.1
next prev parent reply other threads:[~2023-11-28 10:12 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-11-28 10:09 [PATCH v3 0/9] arm64: dts: ti: Enable CSI cameras for AM62 family Jai Luthra
2023-11-28 10:09 ` [PATCH v3 1/9] arm64: defconfig: Enable AM62 CSI2RX Jai Luthra
2023-11-28 10:09 ` [PATCH v3 2/9] arm64: dts: ti: Enable CSI-RX on AM62 Jai Luthra
2023-11-28 10:09 ` [PATCH v3 3/9] arm64: dts: ti: Enable CSI-RX on AM62A Jai Luthra
2023-11-28 10:09 ` [PATCH v3 4/9] arm64: dts: ti: k3-am625-beagleplay: Add overlays for OV5640 Jai Luthra
2023-11-28 10:27 ` Jai Luthra
2023-11-28 14:33 ` Krzysztof Kozlowski
2023-12-01 6:18 ` Nishanth Menon
2023-12-01 9:37 ` Jai Luthra
2023-11-28 10:09 ` [PATCH v3 5/9] arm64: dts: ti: k3-am62x-sk: Enable camera peripherals Jai Luthra
2023-11-28 10:09 ` Jai Luthra [this message]
2023-11-28 10:09 ` [PATCH v3 7/9] arm64: dts: ti: k3-am62a7-sk: " Jai Luthra
2023-11-28 10:09 ` [PATCH v3 8/9] arm64: dts: ti: k3-am62x: Add overlay for IMX219 Jai Luthra
2023-11-28 10:09 ` [PATCH v3 9/9] arm64: dts: ti: Use OF_ALL_DTBS for combined blobs Jai Luthra
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20231128-csi_dts-v3-6-0bb11cfa9d43@ti.com \
--to=j-luthra@ti.com \
--cc=a-bhatia1@ti.com \
--cc=catalin.marinas@arm.com \
--cc=conor+dt@kernel.org \
--cc=devarsht@ti.com \
--cc=devicetree@vger.kernel.org \
--cc=julien.massot@collabora.com \
--cc=kristo@kernel.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=martyn.welch@collabora.com \
--cc=matthias.schiffer@ew.tq-group.com \
--cc=nm@ti.com \
--cc=robh+dt@kernel.org \
--cc=vaishnav.a@ti.com \
--cc=vigneshr@ti.com \
--cc=will@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®