From: Manorit Chawdhry <m-chawdhry@ti.com>
To: Nishanth Menon <nm@ti.com>, Vignesh Raghavendra <vigneshr@ti.com>,
Tero Kristo <kristo@kernel.org>, Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>
Cc: <linux-arm-kernel@lists.infradead.org>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
Neha Malcom Francis <n-francis@ti.com>,
Aniket Limaye <a-limaye@ti.com>, Udit Kumar <u-kumar1@ti.com>,
Beleswar Padhi <b-padhi@ti.com>,
Manorit Chawdhry <m-chawdhry@ti.com>
Subject: [PATCH 2/5] arm64: dts: ti: k3-j784s4*: Remove bootph properties from parent nodes
Date: Tue, 7 May 2024 15:14:29 +0530 [thread overview]
Message-ID: <20240507-b4-upstream-bootph-all-v1-2-c6d52651856f@ti.com> (raw)
In-Reply-To: <20240507-b4-upstream-bootph-all-v1-0-c6d52651856f@ti.com>
Removes bootph-* properties from parent nodes and aligns the bootph-* to
other u-boot.dtsi
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
---
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 10 +---------
arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi | 1 +
arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi | 6 +++---
3 files changed, 5 insertions(+), 12 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
index 81fd7afac8c5..f262eb1a6c65 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
@@ -279,7 +279,6 @@ &wkup_gpio0 {
};
&main_pmx0 {
- bootph-all;
main_uart8_pins_default: main-uart8-default-pins {
bootph-all;
pinctrl-single,pins = <
@@ -339,7 +338,6 @@ J784S4_IOPAD(0x010, PIN_INPUT_PULLUP, 8) /* (AH33) MCAN13_RX.I2C4_SDA */
};
&wkup_pmx2 {
- bootph-all;
wkup_uart0_pins_default: wkup-uart0-default-pins {
bootph-all;
pinctrl-single,pins = <
@@ -429,7 +427,6 @@ J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 7)
};
&wkup_pmx0 {
- bootph-all;
mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
bootph-all;
pinctrl-single,pins = <
@@ -449,7 +446,6 @@ J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */
};
&wkup_pmx1 {
- bootph-all;
mcu_fss0_ospi0_1_pins_default: mcu-fss0-ospi0-1-default-pins {
bootph-all;
pinctrl-single,pins = <
@@ -520,6 +516,7 @@ bucka12: buck12 {
regulator-max-microvolt = <1100000>;
regulator-boot-on;
regulator-always-on;
+ bootph-pre-ram;
};
bucka3: buck3 {
@@ -600,18 +597,15 @@ &ufs_wrapper {
};
&fss {
- bootph-all;
status = "okay";
};
&ospi0 {
- bootph-all;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mcu_fss0_ospi0_pins_default>, <&mcu_fss0_ospi0_1_pins_default>;
flash@0 {
- bootph-all;
compatible = "jedec,spi-nor";
reg = <0x0>;
spi-tx-bus-width = <8>;
@@ -668,13 +662,11 @@ partition@3fc0000 {
};
&ospi1 {
- bootph-all;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mcu_fss0_ospi1_pins_default>;
flash@0 {
- bootph-all;
compatible = "jedec,spi-nor";
reg = <0x0>;
spi-tx-bus-width = <1>;
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
index b67c37460a73..46bd3cd1b006 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
@@ -1120,6 +1120,7 @@ secure_proxy_main: mailbox@32c00000 {
<0x00 0x32800000 0x00 0x100000>;
interrupt-names = "rx_011";
interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ bootph-all;
};
hwspinlock: hwlock@30e00000 {
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
index 77a8d99139ec..951ff3ec3ea0 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
@@ -39,7 +39,6 @@ k3_reset: reset-controller {
};
wkup_conf: bus@43000000 {
- bootph-all;
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
@@ -171,10 +170,10 @@ mcu_timer0: timer@40400000 {
ti,timer-pwm;
/* Non-MPU Firmware usage */
status = "reserved";
+ bootph-all;
};
mcu_timer1: timer@40410000 {
- bootph-all;
compatible = "ti,am654-timer";
reg = <0x00 0x40410000 0x00 0x400>;
interrupts = <GIC_SPI 817 IRQ_TYPE_LEVEL_HIGH>;
@@ -456,7 +455,6 @@ mcu_spi2: spi@40320000 {
};
mcu_navss: bus@28380000 {
- bootph-all;
compatible = "simple-bus";
#address-cells = <2>;
#size-cells = <2>;
@@ -519,6 +517,7 @@ secure_proxy_mcu: mailbox@2a480000 {
* firmware on non-MPU processors
*/
status = "disabled";
+ bootph-pre-ram;
};
mcu_cpsw: ethernet@46000000 {
@@ -630,6 +629,7 @@ wkup_vtm0: temperature-sensor@42040000 {
<0x00 0x42050000 0x00 0x350>;
power-domains = <&k3_pds 243 TI_SCI_PD_SHARED>;
#thermal-sensor-cells = <1>;
+ bootph-pre-ram;
};
tscadc0: tscadc@40200000 {
--
2.43.2
next prev parent reply other threads:[~2024-05-07 9:45 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-05-07 9:44 [PATCH 0/5] Add bootph-all property for J7 boards Manorit Chawdhry
2024-05-07 9:44 ` [PATCH 1/5] arm64: dts: ti: k3-j721s2*: Add bootph-* properties Manorit Chawdhry
2024-05-07 9:44 ` Manorit Chawdhry [this message]
2024-05-07 9:44 ` [PATCH 3/5] arm64: dts: ti: k3-am68*: " Manorit Chawdhry
2024-05-07 9:44 ` [PATCH 4/5] arm64: dts: ti: k3-j721e*: " Manorit Chawdhry
2024-05-07 9:44 ` [PATCH 5/5] arm64: dts: ti: k3-j7200*: " Manorit Chawdhry
2024-05-28 9:05 ` Limaye, Aniket
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240507-b4-upstream-bootph-all-v1-2-c6d52651856f@ti.com \
--to=m-chawdhry@ti.com \
--cc=a-limaye@ti.com \
--cc=b-padhi@ti.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=kristo@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=n-francis@ti.com \
--cc=nm@ti.com \
--cc=robh@kernel.org \
--cc=u-kumar1@ti.com \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®