From: MD Danish Anwar <danishanwar@ti.com>
To: Dan Carpenter <dan.carpenter@linaro.org>,
Jan Kiszka <jan.kiszka@siemens.com>,
Diogo Ivo <diogo.ivo@siemens.com>, Andrew Lunn <andrew@lunn.ch>,
Simon Horman <horms@kernel.org>, Paolo Abeni <pabeni@redhat.com>,
Jakub Kicinski <kuba@kernel.org>,
Eric Dumazet <edumazet@google.com>,
"David S. Miller" <davem@davemloft.net>
Cc: <linux-kernel@vger.kernel.org>, <netdev@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>, <srk@ti.com>,
Vignesh Raghavendra <vigneshr@ti.com>,
Roger Quadros <rogerq@kernel.org>,
MD Danish Anwar <danishanwar@ti.com>,
Wojciech Drewek <wojciech.drewek@intel.com>
Subject: [PATCH net-next v3] net: ti: icssg-prueth: Add multicast filtering support
Date: Wed, 5 Jun 2024 15:22:23 +0530 [thread overview]
Message-ID: <20240605095223.2556963-1-danishanwar@ti.com> (raw)
Add multicast filtering support for ICSSG Driver. Multicast addresses will
be updated by __dev_mc_sync() API. icssg_prueth_add_macst () and
icssg_prueth_del_mcast() will be sync and unsync APIs for the driver
respectively.
To add a mac_address for a port, driver needs to call icssg_fdb_add_del()
and pass the mac_address and BIT(port_id) to the API. The ICSSG firmware
will then configure the rules and allow filtering.
If a mac_address is added to port0 and the same mac_address needs to be
added for port1, driver needs to pass BIT(port0) | BIT(port1) to the
icssg_fdb_add_del() API. If driver just pass BIT(port1) then the entry for
port0 will be overwritten / lost. This is a design constraint on the
firmware side.
To overcome this in the driver, to add any mac_address for let's say portX
driver first checks if the same mac_address is already added for any other
port. If yes driver calls icssg_fdb_add_del() with BIT(portX) |
BIT(other_existing_port). If not, driver calls icssg_fdb_add_del() with
BIT(portX).
The same thing is applicable for deleting mac_addresses as well. This
logic is in icssg_prueth_add_mcast / icssg_prueth_del_mcast APIs.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
---
Cc: Wojciech Drewek <wojciech.drewek@intel.com>
v2 -> v3:
*) Using __dev_mc_sync() instead of __hw_addr_sync_dev().
*) Stopped keeping local copy of multicast list as pointed out by
Wojciech Drewek <wojciech.drewek@intel.com>
v1 -> v2:
*) Rebased on latest net-next/main.
NOTE: This series can be applied cleanly on the tip of net-next/main. This
series doesn't depend on any other ICSSG driver related series that is
floating around in netdev.
v1 https://lore.kernel.org/all/20240516091752.2969092-1-danishanwar@ti.com/
v2 https://lore.kernel.org/all/20240604114402.1835973-1-danishanwar@ti.com/
drivers/net/ethernet/ti/icssg/icssg_prueth.c | 38 +++++++++++++++++---
1 file changed, 34 insertions(+), 4 deletions(-)
diff --git a/drivers/net/ethernet/ti/icssg/icssg_prueth.c b/drivers/net/ethernet/ti/icssg/icssg_prueth.c
index 6e65aa0977d4..e13835100754 100644
--- a/drivers/net/ethernet/ti/icssg/icssg_prueth.c
+++ b/drivers/net/ethernet/ti/icssg/icssg_prueth.c
@@ -439,6 +439,37 @@ const struct icss_iep_clockops prueth_iep_clockops = {
.perout_enable = prueth_perout_enable,
};
+static int icssg_prueth_add_mcast(struct net_device *ndev, const u8 *addr)
+{
+ struct prueth_emac *emac = netdev_priv(ndev);
+ int port_mask = BIT(emac->port_id);
+
+ port_mask |= icssg_fdb_lookup(emac, addr, 0);
+ icssg_fdb_add_del(emac, addr, 0, port_mask, true);
+ icssg_vtbl_modify(emac, 0, port_mask, port_mask, true);
+
+ return 0;
+}
+
+static int icssg_prueth_del_mcast(struct net_device *ndev, const u8 *addr)
+{
+ struct prueth_emac *emac = netdev_priv(ndev);
+ int port_mask = BIT(emac->port_id);
+ int other_port_mask;
+
+ other_port_mask = port_mask ^ icssg_fdb_lookup(emac, addr, 0);
+
+ icssg_fdb_add_del(emac, addr, 0, port_mask, false);
+ icssg_vtbl_modify(emac, 0, port_mask, port_mask, false);
+
+ if (other_port_mask) {
+ icssg_fdb_add_del(emac, addr, 0, other_port_mask, true);
+ icssg_vtbl_modify(emac, 0, other_port_mask, other_port_mask, true);
+ }
+
+ return 0;
+}
+
/**
* emac_ndo_open - EMAC device open
* @ndev: network adapter device
@@ -599,6 +630,8 @@ static int emac_ndo_stop(struct net_device *ndev)
icssg_class_disable(prueth->miig_rt, prueth_emac_slice(emac));
+ __dev_mc_unsync(ndev, icssg_prueth_del_mcast);
+
atomic_set(&emac->tdown_cnt, emac->tx_ch_num);
/* ensure new tdown_cnt value is visible */
smp_mb__after_atomic();
@@ -675,10 +708,7 @@ static void emac_ndo_set_rx_mode_work(struct work_struct *work)
return;
}
- if (!netdev_mc_empty(ndev)) {
- emac_set_port_state(emac, ICSSG_EMAC_PORT_MC_FLOODING_ENABLE);
- return;
- }
+ __dev_mc_sync(ndev, icssg_prueth_add_mcast, icssg_prueth_del_mcast);
}
/**
base-commit: fd70f0443e24c3888bf4b7f198df6d705c9b8ab2
--
2.34.1
next reply other threads:[~2024-06-05 9:52 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-06-05 9:52 MD Danish Anwar [this message]
2024-06-05 10:02 ` Wojciech Drewek
2024-06-07 13:32 ` patchwork-bot+netdevbpf
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240605095223.2556963-1-danishanwar@ti.com \
--to=danishanwar@ti.com \
--cc=andrew@lunn.ch \
--cc=dan.carpenter@linaro.org \
--cc=davem@davemloft.net \
--cc=diogo.ivo@siemens.com \
--cc=edumazet@google.com \
--cc=horms@kernel.org \
--cc=jan.kiszka@siemens.com \
--cc=kuba@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=netdev@vger.kernel.org \
--cc=pabeni@redhat.com \
--cc=rogerq@kernel.org \
--cc=srk@ti.com \
--cc=vigneshr@ti.com \
--cc=wojciech.drewek@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®