From: Bastien Curutchet <bastien.curutchet@bootlin.com>
To: Santosh Shilimkar <ssantosh@kernel.org>,
Krzysztof Kozlowski <krzk@kernel.org>,
Miquel Raynal <miquel.raynal@bootlin.com>,
Richard Weinberger <richard@nod.at>,
Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-kernel@vger.kernel.org, linux-mtd@lists.infradead.org,
Thomas Petazzoni <thomas.petazzoni@bootlin.com>,
Herve Codina <herve.codina@bootlin.com>,
Christopher Cordahi <christophercordahi@nanometrics.ca>,
Bastien Curutchet <bastien.curutchet@bootlin.com>
Subject: [PATCH 2/5] memory: ti-aemif: export aemif_set_cs_timing()
Date: Wed, 30 Oct 2024 11:47:14 +0100 [thread overview]
Message-ID: <20241030104717.88688-3-bastien.curutchet@bootlin.com> (raw)
In-Reply-To: <20241030104717.88688-1-bastien.curutchet@bootlin.com>
Export the aemif_set_cs_timing() symbol so it can be used by other
drivers
Add a spinlock to protect the CS configuration register from concurrent
accesses.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
---
drivers/memory/ti-aemif.c | 35 +++++++++++++----------------------
include/memory/ti-aemif.h | 31 +++++++++++++++++++++++++++++++
2 files changed, 44 insertions(+), 22 deletions(-)
create mode 100644 include/memory/ti-aemif.h
diff --git a/drivers/memory/ti-aemif.c b/drivers/memory/ti-aemif.c
index 5be6df246075..ee857c16a02c 100644
--- a/drivers/memory/ti-aemif.c
+++ b/drivers/memory/ti-aemif.c
@@ -17,6 +17,8 @@
#include <linux/of.h>
#include <linux/of_platform.h>
#include <linux/platform_device.h>
+#include <linux/spinlock.h>
+#include <memory/ti-aemif.h>
#define TA_SHIFT 2
#define RHOLD_SHIFT 4
@@ -107,27 +109,6 @@ struct aemif_cs_data {
u8 asize;
};
-/**
- * struct aemif_cs_timing: structure to hold cs timing configuration
- * values are expressed in number of clock cycles - 1
- * @ta: minimum turn around time
- * @rhold read hold width
- * @rstrobe read strobe width
- * @rsetup read setup width
- * @whold write hold width
- * @wstrobe write strobe width
- * @wsetup write setup width
- */
-struct aemif_cs_timings {
- u32 ta;
- u32 rhold;
- u32 rstrobe;
- u32 rsetup;
- u32 whold;
- u32 wstrobe;
- u32 wsetup;
-};
-
/**
* struct aemif_device: structure to hold device data
* @base: base address of AEMIF registers
@@ -136,6 +117,7 @@ struct aemif_cs_timings {
* @num_cs: number of assigned chip-selects
* @cs_offset: start number of cs nodes
* @cs_data: array of chip-select settings
+ * @cs_config_lock: lock used to access CS configuration
*/
struct aemif_device {
void __iomem *base;
@@ -144,6 +126,7 @@ struct aemif_device {
u8 num_cs;
int cs_offset;
struct aemif_cs_data cs_data[NUM_CS];
+ spinlock_t config_cs_lock;
};
/**
@@ -154,8 +137,9 @@ struct aemif_device {
*
* Returns 0 on success, else negative errno.
*/
-static int aemif_set_cs_timings(struct aemif_device *aemif, u8 cs, struct aemif_cs_timings *timings)
+int aemif_set_cs_timings(struct aemif_device *aemif, u8 cs, struct aemif_cs_timings *timings)
{
+ unsigned long flags;
unsigned int offset;
u32 val, set;
@@ -176,13 +160,16 @@ static int aemif_set_cs_timings(struct aemif_device *aemif, u8 cs, struct aemif_
offset = A1CR_OFFSET + cs * 4;
+ spin_lock_irqsave(&aemif->config_cs_lock, flags);
val = readl(aemif->base + offset);
val &= ~TIMINGS_MASK;
val |= set;
writel(val, aemif->base + offset);
+ spin_unlock_irqrestore(&aemif->config_cs_lock, flags);
return 0;
}
+EXPORT_SYMBOL(aemif_set_cs_timings);
/**
* aemif_calc_rate - calculate timing data.
@@ -231,6 +218,7 @@ static int aemif_config_abus(struct platform_device *pdev, int csnum)
struct aemif_cs_data *data = &aemif->cs_data[csnum];
unsigned long clk_rate = aemif->clk_rate;
struct aemif_cs_timings timings;
+ unsigned long flags;
unsigned offset;
u32 set, val;
@@ -250,10 +238,12 @@ static int aemif_config_abus(struct platform_device *pdev, int csnum)
if (data->enable_ss)
set |= ACR_SSTROBE_MASK;
+ spin_lock_irqsave(&aemif->config_cs_lock, flags);
val = readl(aemif->base + offset);
val &= ~CONFIG_MASK;
val |= set;
writel(val, aemif->base + offset);
+ spin_unlock_irqrestore(&aemif->config_cs_lock, flags);
return aemif_set_cs_timings(aemif, data->cs - aemif->cs_offset, &timings);
}
@@ -396,6 +386,7 @@ static int aemif_probe(struct platform_device *pdev)
if (IS_ERR(aemif->base))
return PTR_ERR(aemif->base);
+ spin_lock_init(&aemif->config_cs_lock);
if (np) {
/*
* For every controller device node, there is a cs device node
diff --git a/include/memory/ti-aemif.h b/include/memory/ti-aemif.h
new file mode 100644
index 000000000000..a1478387a8d0
--- /dev/null
+++ b/include/memory/ti-aemif.h
@@ -0,0 +1,31 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifndef __TI_AEMIF_H
+#define __TI_AEMIF_H
+
+/**
+ * struct aemif_cs_timing: structure to hold cs timing configuration
+ * values are expressed in number of clock cycles - 1
+ * @ta: minimum turn around time
+ * @rhold read hold width
+ * @rstrobe read strobe width
+ * @rsetup read setup width
+ * @whold write hold width
+ * @wstrobe write strobe width
+ * @wsetup write setup width
+ */
+struct aemif_cs_timings {
+ u32 ta;
+ u32 rhold;
+ u32 rstrobe;
+ u32 rsetup;
+ u32 whold;
+ u32 wstrobe;
+ u32 wsetup;
+};
+
+struct aemif_device;
+
+int aemif_set_cs_timings(struct aemif_device *aemif, u8 cs, struct aemif_cs_timings *timings);
+
+#endif // __TI_AEMIF_H
--
2.47.0
next prev parent reply other threads:[~2024-10-30 10:47 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-10-30 10:47 [PATCH 0/5] Implement setup_inteface() in the DaVinci NAND controller Bastien Curutchet
2024-10-30 10:47 ` [PATCH 1/5] memory: ti-aemif: Create aemif_set_cs_timings() Bastien Curutchet
2024-10-30 10:47 ` Bastien Curutchet [this message]
2024-10-31 5:42 ` [PATCH 2/5] memory: ti-aemif: export aemif_set_cs_timing() kernel test robot
2024-10-30 10:47 ` [PATCH 3/5] mtd: rawnand: davinci: Order headers alphabetically Bastien Curutchet
2024-10-30 10:47 ` [PATCH 4/5] mtd: rawnand: davinci: Add clock resource Bastien Curutchet
2024-10-30 11:17 ` Krzysztof Kozlowski
2024-10-30 12:20 ` Bastien Curutchet
2024-10-30 14:26 ` Krzysztof Kozlowski
2024-10-30 10:47 ` [PATCH 5/5] mtd: rawnand: davinci: Implement setup_interface() operation Bastien Curutchet
2024-11-01 18:11 ` kernel test robot
2024-11-02 2:04 ` kernel test robot
2024-10-30 11:17 ` [PATCH 0/5] Implement setup_inteface() in the DaVinci NAND controller Krzysztof Kozlowski
2024-10-30 12:39 ` Bastien Curutchet
2024-10-30 14:25 ` Krzysztof Kozlowski
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20241030104717.88688-3-bastien.curutchet@bootlin.com \
--to=bastien.curutchet@bootlin.com \
--cc=christophercordahi@nanometrics.ca \
--cc=herve.codina@bootlin.com \
--cc=krzk@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mtd@lists.infradead.org \
--cc=miquel.raynal@bootlin.com \
--cc=richard@nod.at \
--cc=ssantosh@kernel.org \
--cc=thomas.petazzoni@bootlin.com \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®