From: Melody Olvera <quic_molvera@quicinc.com>
To: "Bjorn Andersson" <andersson@kernel.org>,
"Konrad Dybcio" <konradybcio@kernel.org>,
"Rob Herring" <robh@kernel.org>,
"Krzysztof Kozlowski" <krzk+dt@kernel.org>,
"Conor Dooley" <conor+dt@kernel.org>,
"Catalin Marinas" <catalin.marinas@arm.com>,
"Will Deacon" <will@kernel.org>,
"Geert Uytterhoeven" <geert+renesas@glider.be>,
"Dmitry Baryshkov" <dmitry.baryshkov@linaro.org>,
"Neil Armstrong" <neil.armstrong@linaro.org>,
"Arnd Bergmann" <arnd@arndb.de>,
"Nícolas F . R . A . Prado" <nfraprado@collabora.com>,
"Trilok Soni" <quic_tsoni@quicinc.com>,
"Satya Durga Srinivasu Prabhala" <quic_satyap@quicinc.com>
Cc: <linux-arm-msm@vger.kernel.org>, <devicetree@vger.kernel.org>,
<linux-kernel@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
Melody Olvera <quic_molvera@quicinc.com>
Subject: [PATCH v2 4/6] arm64: dts: qcom: sm8750: Add pmic dtsi
Date: Mon, 11 Nov 2024 16:49:34 -0800 [thread overview]
Message-ID: <20241112004936.2810509-5-quic_molvera@quicinc.com> (raw)
In-Reply-To: <20241112004936.2810509-1-quic_molvera@quicinc.com>
Add pmic dtsi file for SM8750 SoC describing the pmics and
their thermal zones.
Signed-off-by: Melody Olvera <quic_molvera@quicinc.com>
---
arch/arm64/boot/dts/qcom/sm8750-pmics.dtsi | 188 +++++++++++++++++++++
1 file changed, 188 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/sm8750-pmics.dtsi
diff --git a/arch/arm64/boot/dts/qcom/sm8750-pmics.dtsi b/arch/arm64/boot/dts/qcom/sm8750-pmics.dtsi
new file mode 100644
index 000000000000..6eb8d78937c3
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm8750-pmics.dtsi
@@ -0,0 +1,188 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/ {
+ thermal-zones {
+ pm8550ve-d-thermal {
+ polling-delay-passive = <100>;
+
+ thermal-sensors = <&pm8550ve_d_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pm8550ve-f-thermal {
+ polling-delay-passive = <100>;
+
+ thermal-sensors = <&pm8550ve_f_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pm8550ve-g-thermal {
+ polling-delay-passive = <100>;
+
+ thermal-sensors = <&pm8550ve_g_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pm8550vs-j-thermal {
+ polling-delay-passive = <100>;
+
+ thermal-sensors = <&pm8550vs_j_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+ };
+};
+
+&spmi_bus {
+ /* PM8550VE */
+ pm8550ve_d: pmic@3 {
+ compatible = "qcom,pm8550ve", "qcom,spmi-pmic";
+ reg = <0x3 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8550ve_d_temp_alarm: temp-alarm@a00 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0xa00>;
+ interrupts = <0x3 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ pm8550ve_d_gpios: gpio@8800 {
+ compatible = "qcom,pm8550ve-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pm8550ve_d_gpios 0 0 8>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pm8550ve_f: pmic@5 {
+ compatible = "qcom,pm8550ve", "qcom,spmi-pmic";
+ reg = <0x5 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8550ve_f_temp_alarm: temp-alarm@a00 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0xa00>;
+ interrupts = <0x5 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ pm8550ve_f_gpios: gpio@8800 {
+ compatible = "qcom,pm8550ve-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pm8550ve_f_gpios 0 0 6>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pm8550ve_g: pmic@6 {
+ compatible = "qcom,pm8550ve", "qcom,spmi-pmic";
+ reg = <0x6 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8550ve_g_temp_alarm: temp-alarm@a00 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0xa00>;
+ interrupts = <0x6 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ pm8550ve_g_gpios: gpio@8800 {
+ compatible = "qcom,pm8550ve-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pm8550ve_g_gpios 0 0 8>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ /* PM8550VS */
+ pm8550vs_j: pmic@9 {
+ compatible = "qcom,pm8550vs", "qcom,spmi-pmic";
+ reg = <0x9 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8550vs_j_temp_alarm: temp-alarm@a00 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0xa00>;
+ interrupts = <0x9 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ pm8550vs_j_gpios: gpio@8800 {
+ compatible = "qcom,pm8550vs-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pm8550vs_j_gpios 0 0 6>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+};
--
2.46.1
next prev parent reply other threads:[~2024-11-12 0:50 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-11-12 0:49 [PATCH v2 0/6] dts: qcom: Introduce SM8750 device trees Melody Olvera
2024-11-12 0:49 ` [PATCH v2 1/6] dt-bindings: arm: qcom: Document sm8750 SoC and boards Melody Olvera
2024-11-15 14:49 ` Dmitry Baryshkov
2024-11-18 22:08 ` Melody Olvera
2024-11-12 0:49 ` [PATCH v2 2/6] arm64: dts: qcom: Add pmd8028 and pmih0108 PMICs Melody Olvera
2024-11-15 14:58 ` Dmitry Baryshkov
2024-11-18 22:16 ` Melody Olvera
2024-11-12 0:49 ` [PATCH v2 3/6] arm64: dts: qcom: Add base SM8750 dtsi Melody Olvera
2024-11-15 20:26 ` Konrad Dybcio
2024-11-12 0:49 ` Melody Olvera [this message]
2024-11-12 0:49 ` [PATCH v2 5/6] arm64: dts: qcom: Add SM8750 MTP and QRD boards Melody Olvera
2024-11-12 0:49 ` [PATCH v2 6/6] arm64: defconfig: Enable SM8750 SoC base configs Melody Olvera
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20241112004936.2810509-5-quic_molvera@quicinc.com \
--to=quic_molvera@quicinc.com \
--cc=andersson@kernel.org \
--cc=arnd@arndb.de \
--cc=catalin.marinas@arm.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=dmitry.baryshkov@linaro.org \
--cc=geert+renesas@glider.be \
--cc=konradybcio@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=neil.armstrong@linaro.org \
--cc=nfraprado@collabora.com \
--cc=quic_satyap@quicinc.com \
--cc=quic_tsoni@quicinc.com \
--cc=robh@kernel.org \
--cc=will@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®