[PATCH] iio: ABI: combine current input sections

[David Lechner <dlechner@baylibre.com>]

Combine two duplicate sections describing in_currentY_raw.

This went unnoticed until we renamed in_currentX_raw to in_currentY_raw
and the kernel test robot found the duplication.

Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202412200256.OB5Hmw5Q-lkp@intel.com/
Signed-off-by: David Lechner <dlechner@baylibre.com>
---
 Documentation/ABI/testing/sysfs-bus-iio | 19 +++++--------------
 1 file changed, 5 insertions(+), 14 deletions(-)

diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio
index d97c35057a034c76ed433e3e6de0aff8ec4bbb70..25d366d452a55293c420300335a0271a28855107 100644
--- a/Documentation/ABI/testing/sysfs-bus-iio
+++ b/Documentation/ABI/testing/sysfs-bus-iio
@@ -168,18 +168,6 @@ Description:
 		is required is a consistent labeling.  Units after application
 		of scale and offset are millivolts.
 
-What:		/sys/bus/iio/devices/iio:deviceX/in_currentY_raw
-What:		/sys/bus/iio/devices/iio:deviceX/in_currentY_supply_raw
-KernelVersion:	3.17
-Contact:	linux-iio@vger.kernel.org
-Description:
-		Raw (unscaled no bias removal etc.) current measurement from
-		channel Y. In special cases where the channel does not
-		correspond to externally available input one of the named
-		versions may be used. The number must always be specified and
-		unique to allow association with event codes. Units after
-		application of scale and offset are milliamps.
-
 What:		/sys/bus/iio/devices/iio:deviceX/in_powerY_raw
 KernelVersion:	4.5
 Contact:	linux-iio@vger.kernel.org
@@ -1700,15 +1688,18 @@ Description:
 		or without compensation from tilt sensors.
 
 What:		/sys/bus/iio/devices/iio:deviceX/in_currentY_raw
+What:		/sys/bus/iio/devices/iio:deviceX/in_currentY_supply_raw
 What:		/sys/bus/iio/devices/iio:deviceX/in_currentY_i_raw
 What:		/sys/bus/iio/devices/iio:deviceX/in_currentY_q_raw
-KernelVersion:	3.18
+KernelVersion:	3.17
 Contact:	linux-iio@vger.kernel.org
 Description:
 		Raw current measurement from channel Y. Units are in milliamps
 		after application of scale and offset. If no offset or scale is
 		present, output should be considered as processed with the
-		unit in milliamps.
+		unit in milliamps. In special cases where the channel does not
+		correspond to externally available input one of the named
+		versions may be used.
 
 		Channels with 'i' and 'q' modifiers always exist in pairs and both
 		channels refer to the same signal. The 'i' channel contains the in-phase

---
base-commit: fe2a04fbcbfe44694fcb36ff6212fce54b8f56cc
change-id: 20241219-iio-abi-combine-current-input-sections-c62cf5dbfa9b

Best regards,
-- 
David Lechner <dlechner@baylibre.com>