Re: [PATCH 2/8] scsi: ufs: qcom: Pass target_freq to clk scale pre and post change

[Manivannan Sadhasivam <mani@kernel.org>]

On Thu, Jan 16, 2025 at 05:11:43PM +0800, Ziqi Chen wrote:
> From: Can Guo <quic_cang@quicinc.com>
> 
> If OPP V2 is used, devfreq clock scaling may scale clock amongst more than
> two freqs.

Same comment as previous patch.

> In the case of scaling up, the devfreq may decide to scale the
> clock to an intermidiate freq base on load, but the clock scale up pre
> change operation uses settings for the max clock freq unconditionally. Fix
> it by passing the target_freq to clock scale up pre change so that the
> correct settings for the target_freq can be used.
> 
> In the case of scaling down, the clock scale down post change operation
> is doing fine, because it reads the actual clock rate to tell freq, but to
> keep symmetry with clock scale up pre change operation, just use the
> target_freq instead of reading clock rate.
> 
> Co-developed-by: Ziqi Chen <quic_ziqichen@quicinc.com>
> Signed-off-by: Ziqi Chen <quic_ziqichen@quicinc.com>
> Signed-off-by: Can Guo <quic_cang@quicinc.com>
> ---
>  drivers/ufs/host/ufs-qcom.c | 23 ++++++++++++-----------
>  1 file changed, 12 insertions(+), 11 deletions(-)
> 
> diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
> index b6eef975dc46..1e8a23eb8c13 100644
> --- a/drivers/ufs/host/ufs-qcom.c
> +++ b/drivers/ufs/host/ufs-qcom.c
> @@ -97,7 +97,7 @@ static const struct __ufs_qcom_bw_table {
>  };
>  
>  static void ufs_qcom_get_default_testbus_cfg(struct ufs_qcom_host *host);
> -static int ufs_qcom_set_core_clk_ctrl(struct ufs_hba *hba, bool is_scale_up);
> +static int ufs_qcom_set_core_clk_ctrl(struct ufs_hba *hba, unsigned long freq);
>  
>  static struct ufs_qcom_host *rcdev_to_ufs_host(struct reset_controller_dev *rcd)
>  {
> @@ -524,7 +524,7 @@ static int ufs_qcom_link_startup_notify(struct ufs_hba *hba,
>  			return -EINVAL;
>  		}
>  
> -		err = ufs_qcom_set_core_clk_ctrl(hba, true);
> +		err = ufs_qcom_set_core_clk_ctrl(hba, ULONG_MAX);
>  		if (err)
>  			dev_err(hba->dev, "cfg core clk ctrl failed\n");
>  		/*
> @@ -1231,7 +1231,7 @@ static int ufs_qcom_set_clk_40ns_cycles(struct ufs_hba *hba,
>  	return ufshcd_dme_set(hba, UIC_ARG_MIB(PA_VS_CORE_CLK_40NS_CYCLES), reg);
>  }
>  
> -static int ufs_qcom_set_core_clk_ctrl(struct ufs_hba *hba, bool is_scale_up)
> +static int ufs_qcom_set_core_clk_ctrl(struct ufs_hba *hba, unsigned long freq)
>  {
>  	struct ufs_qcom_host *host = ufshcd_get_variant(hba);
>  	struct list_head *head = &hba->clk_list_head;
> @@ -1245,10 +1245,11 @@ static int ufs_qcom_set_core_clk_ctrl(struct ufs_hba *hba, bool is_scale_up)
>  		    !strcmp(clki->name, "core_clk_unipro")) {
>  			if (!clki->max_freq)
>  				cycles_in_1us = 150; /* default for backwards compatibility */
> -			else if (is_scale_up)
> +			else if (freq == ULONG_MAX)
>  				cycles_in_1us = ceil(clki->max_freq, (1000 * 1000));
>  			else
> -				cycles_in_1us = ceil(clk_get_rate(clki->clk), (1000 * 1000));
> +				cycles_in_1us = ceil(freq, (1000 * 1000));

Consider switching to HZ_PER_MHZ in a separate patch later.

- Mani

-- 
மணிவண்ணன் சதாசிவம்