[PATCH 3/4] dt-bindings: memory-controllers: samsung,exynos4210-srom: Split out child node properties

["Rob Herring (Arm)" <robh@kernel.org>]

In order to validate devices in child nodes, the device schemas need to
reference any child node properties. In order to do that, the properties
for child nodes need to be included in mc-peripheral-props.yaml.

"reg: { maxItems: 1 }" was also incorrect. It's up to the device schemas
how many reg entries they have.

Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
---
 .../bindings/memory-controllers/exynos-srom.yaml   | 35 ----------------------
 .../memory-controllers/mc-peripheral-props.yaml    |  1 +
 .../samsung,exynos4210-srom-peripheral-props.yaml  | 35 ++++++++++++++++++++++
 3 files changed, 36 insertions(+), 35 deletions(-)

diff --git a/Documentation/devicetree/bindings/memory-controllers/exynos-srom.yaml b/Documentation/devicetree/bindings/memory-controllers/exynos-srom.yaml
index a5598ade399f..2267c5107d60 100644
--- a/Documentation/devicetree/bindings/memory-controllers/exynos-srom.yaml
+++ b/Documentation/devicetree/bindings/memory-controllers/exynos-srom.yaml
@@ -39,49 +39,14 @@ patternProperties:
   "^.*@[0-3],[a-f0-9]+$":
     type: object
     additionalProperties: true
-    description:
-      The actual device nodes should be added as subnodes to the SROMc node.
-      These subnodes, in addition to regular device specification, should
-      contain the following properties, describing configuration
-      of the relevant SROM bank.
 
     properties:
-      reg:
-        description:
-          Bank number, base address (relative to start of the bank) and size
-          of the memory mapped for the device. Note that base address will be
-          typically 0 as this is the start of the bank.
-        maxItems: 1
-
       reg-io-width:
         enum: [1, 2]
         description:
           Data width in bytes (1 or 2). If omitted, default of 1 is used.
 
-      samsung,srom-page-mode:
-        description:
-          If page mode is set, 4 data page mode will be configured,
-          else normal (1 data) page mode will be set.
-        type: boolean
-
-      samsung,srom-timing:
-        $ref: /schemas/types.yaml#/definitions/uint32-array
-        minItems: 6
-        maxItems: 6
-        description: |
-          Array of 6 integers, specifying bank timings in the following order:
-          Tacp, Tcah, Tcoh, Tacc, Tcos, Tacs.
-          Each value is specified in cycles and has the following meaning
-          and valid range:
-          Tacp: Page mode access cycle at Page mode (0 - 15)
-          Tcah: Address holding time after CSn (0 - 15)
-          Tcoh: Chip selection hold on OEn (0 - 15)
-          Tacc: Access cycle (0 - 31, the actual time is N + 1)
-          Tcos: Chip selection set-up before OEn (0 - 15)
-          Tacs: Address set-up before CSn (0 - 15)
-
     required:
-      - reg
       - samsung,srom-timing
 
 required:
diff --git a/Documentation/devicetree/bindings/memory-controllers/mc-peripheral-props.yaml b/Documentation/devicetree/bindings/memory-controllers/mc-peripheral-props.yaml
index 11bc8a33d022..73a6dac946b7 100644
--- a/Documentation/devicetree/bindings/memory-controllers/mc-peripheral-props.yaml
+++ b/Documentation/devicetree/bindings/memory-controllers/mc-peripheral-props.yaml
@@ -37,6 +37,7 @@ allOf:
   - $ref: ingenic,nemc-peripherals.yaml#
   - $ref: intel,ixp4xx-expansion-peripheral-props.yaml#
   - $ref: qcom,ebi2-peripheral-props.yaml#
+  - $ref: samsung,exynos4210-srom-peripheral-props.yaml#
   - $ref: ti,gpmc-child.yaml#
   - $ref: fsl/fsl,imx-weim-peripherals.yaml
 
diff --git a/Documentation/devicetree/bindings/memory-controllers/samsung,exynos4210-srom-peripheral-props.yaml b/Documentation/devicetree/bindings/memory-controllers/samsung,exynos4210-srom-peripheral-props.yaml
new file mode 100644
index 000000000000..c474f90846e5
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/samsung,exynos4210-srom-peripheral-props.yaml
@@ -0,0 +1,35 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/samsung,exynos4210-srom-peripheral-props.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Peripheral Properties for Samsung Exynos SoC SROM Controller
+
+maintainers:
+  - Krzysztof Kozlowski <krzk@kernel.org>
+
+properties:
+  samsung,srom-page-mode:
+    description:
+      If page mode is set, 4 data page mode will be configured,
+      else normal (1 data) page mode will be set.
+    type: boolean
+
+  samsung,srom-timing:
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    minItems: 6
+    maxItems: 6
+    description: |
+      Array of 6 integers, specifying bank timings in the following order:
+      Tacp, Tcah, Tcoh, Tacc, Tcos, Tacs.
+      Each value is specified in cycles and has the following meaning
+      and valid range:
+      Tacp: Page mode access cycle at Page mode (0 - 15)
+      Tcah: Address holding time after CSn (0 - 15)
+      Tcoh: Chip selection hold on OEn (0 - 15)
+      Tacc: Access cycle (0 - 31, the actual time is N + 1)
+      Tcos: Chip selection set-up before OEn (0 - 15)
+      Tacs: Address set-up before CSn (0 - 15)
+
+additionalProperties: true

-- 
2.47.2