[PATCH 6/7] alpha: machine check handler for tsunami

[Magnus Lindholm <linmag7@gmail.com>]

err_tsunami.h contains error messages and mask used to
parse data from logout frames for the tsunami platform.

Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
---
 arch/alpha/kernel/err_tsunami.h | 199 ++++++++++++++++++++++++++++++++
 1 file changed, 199 insertions(+)
 create mode 100644 arch/alpha/kernel/err_tsunami.h

diff --git a/arch/alpha/kernel/err_tsunami.h b/arch/alpha/kernel/err_tsunami.h
new file mode 100644
index 000000000000..c20cd72f6a53
--- /dev/null
+++ b/arch/alpha/kernel/err_tsunami.h
@@ -0,0 +1,199 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ *
+ *	Author:	Magnus Lindholm linmag7@gmail.com
+ *
+ *	Contains declarations and macros to support Alpha error handling
+ *      and error messages for the tsunami/typhoon based platforms
+ */
+
+static char *CLIPPER_EnvQW1SMIR[] = {
+"System Power Supply state change detected",
+"OCP or RMC halt detected",
+"Sys_DC_Notok failure detected",
+"",
+"System temperature over 50 degrees C failure",
+"PCI Bus #0 is in reset",
+"PCI Bus #1 is in reset",
+"System is being reset"
+};
+
+#define CLIPPER_ENV_QW1SMIR_POWER_MASK	1L
+#define CLIPPER_EVN_QW1SMIR_RMC_MASK	(1L<<1)
+#define CLIPPER_EVN_QW1SMIR_DC_MASK	(1L<<2)
+#define CLIPPER_EVN_QW1SMIR_TEMP_MASK	(1L<<4)
+#define CLIPPER_ENV_SMIR_MASK (CLIPPER_ENV_QW1SMIR_POWER_MASK |	\
+				CLIPPER_EVN_QW1SMIR_RMC_MASK |	\
+				CLIPPER_EVN_QW1SMIR_DC_MASK |	\
+				CLIPPER_EVN_QW1SMIR_TEMP_MASK)
+static char *CLIPPER_EnvQW2CPUIR[] = {
+"CPU0 regulator is enabled",
+"CPU1 regulator is enabled",
+"CPU2 regulator is enabled",
+"CPU3 regulator is enabled",
+"CPU0 regulator or configuration sequence fail",
+"CPU1 regulator or configuration sequence fail",
+"CPU2 regulator or configuration sequence fail",
+"CPU3 regulator or configuration sequence fail"
+};
+
+#define CLIPPER_ENV_QW2CPUIR_CPU0_ENA_MASK	1L
+#define CLIPPER_ENV_QW2CPUIR_CPU1_ENA_MASK	(1L<<1)
+#define CLIPPER_ENV_QW2CPUIR_CPU2_ENA_MASK	(1L<<2)
+#define CLIPPER_ENV_QW2CPUIR_CPU3_ENA_MASK	(1L<<3)
+#define CLIPPER_ENV_QW2CPUIR_CPU0_FAIL_MASK	(1L<<4)
+#define CLIPPER_ENV_QW2CPUIR_CPU1_FAIL_MASK	(1L<<5)
+#define CLIPPER_ENV_QW2CPUIR_CPU2_FAIL_MASK	(1L<<6)
+#define CLIPPER_ENV_QW2CPUIR_CPU3_FAIL_MASK	(1L<<7)
+#define CLIPPER_ENV_CPUIR_MASK	(CLIPPER_ENV_QW2CPUIR_CPU0_FAIL_MASK |	\
+				CLIPPER_ENV_QW2CPUIR_CPU1_FAIL_MASK |	\
+				CLIPPER_ENV_QW2CPUIR_CPU2_FAIL_MASK |	\
+				CLIPPER_ENV_QW2CPUIR_CPU3_FAIL_MASK)
+
+
+static char *CLIPPER_EnvQW3PSIR[] = {
+"Power Supply 0 is enabled",
+"Power Supply 1 is enabled",
+"Power Supply 2 is enabled",
+"",
+"Power Supply 0 was enabled but failed",
+"Power Supply 1 was enabled but failed",
+"Power Supply 2 was enabled but failed"
+};
+
+#define CLIPPER_PSIR_PSU0_ENA_MASK	1L
+#define CLIPPER_PSIR_PSU1_ENA_MASK	(1L<<1)
+#define CLIPPER_PSIR_PSU2_ENA_MASK	(1L<<2)
+#define CLIPPER_PSIR_PSU0_FAIL_MASK	(1L<<4)
+#define CLIPPER_PSIR_PSU1_FAIL_MASK	(1L<<5)
+#define CLIPPER_PSIR_PSU2_FAIL_MASK	(1L<<6)
+#define CLIPPER_ENV_PSIR_ENA_MASK (CLIPPER_PSIR_PSU0_ENA_MASK	|	\
+				CLIPPER_PSIR_PSU1_ENA_MASK	|	\
+				CLIPPER_PSIR_PSU2_ENA_MASK)
+#define CLIPPER_ENV_PSIR_ERR_MASK (CLIPPER_PSIR_PSU0_FAIL_MASK	|	\
+				CLIPPER_PSIR_PSU1_FAIL_MASK	|	\
+				CLIPPER_PSIR_PSU2_FAIL_MASK)
+
+static char *CLIPPER_EnvQW4LM78ISR[] = {
+"PS +3.3V out of tolerance",
+"PS +5V out of tolerance",
+"PS +12V out of tolerance",
+"VTERM out of tolerance",
+"Temperature zone 0 (PCI Backplane slots 1-3 area) over limit failure",
+"LM75 CPU0-3 Temperature over limit failure",
+"System Fan 1 failure",
+"System Fan 2 failure",
+"CTERM out of tolerance",
+"",
+"-12V out of tolerance",
+"",
+"",
+"",
+"",
+"",
+"CPU0_VCORE +2V out of tolerance",
+"CPU0_VIO +1.5V out of tolerance",
+"CPU1_VCORE +2V out of tolerance",
+"CPU1_VIO +1.5V out of tolerance",
+"Temperature zone 1 (PCI Backplane slots 7-10 area) over limit failure",
+"",
+"System Fan 4 failure",
+"System Fan 5 failure",
+"",
+"",
+"",
+"",
+"",
+"",
+"",
+"",
+"CPU2_VCORE +2V out of tolerance",
+"CPU2_VIO +1.5V out of tolerance",
+"CPU3_VCORE +2V out of tolerance",
+"CPU3_VIO +1.5V out of tolerance",
+"Temperature zone 2 (PCI Backplane slots 4-6 area) over limit failure",
+"",
+"System Fan 3 failure",
+"System Fan 6 failure",
+"",
+"",
+"Power supply 3.3V rail above high amperage warning",
+"Power supply 5.0V rail above high amperage warning",
+"Power supply 12V rail above high amperage warning",
+"Power supply high temperature warning",
+"Power supply AC input low limit warning",
+"Power supply AC input high limit warning"
+};
+
+#define CLIPPER_ENV_LM78ISR_MASK	0xFCDF00DF05FFL
+
+static char *CLIPPER_EnvQW5DOOR[] = {
+"",
+"Set = System CPU door is open",
+"Set = System Fan door is open",
+"Set = System PCI door is open",
+"",
+"Set = System CPU door is closed",
+"Set = System Fan door is closed",
+"Set = System PCI door is closed"
+};
+
+#define CLIPPER_ENV_DOORS_MASK	 0xEEL
+
+static char *CLIPPER_EnvQW6TEMP[] = {
+"CPU0 temperature warning fault has occurred",
+"CPU1 temperature warning fault has occurred",
+"CPU2 temperature warning fault has occurred",
+"CPU3 temperature warning fault has occurred",
+"System temperature zone 0 warning fault has occurred",
+"System temperature zone 1 warning fault has occurred",
+"System temperature zone 2 warning fault has occurred"
+};
+
+#define CLIPPER_ENV_TEMP_MASK	0xFFL
+
+static char *CLIPPER_EnvQW7FAN[] = {
+"System Fan 1 is not responding to RMC Commands",
+"System Fan 2 is not responding to RMC Commands",
+"System Fan 3 is not responding to RMC Commands",
+"System Fan 4 is not responding to RMC Commands",
+"System Fan 5 is not responding to RMC Commands",
+"System Fan 6 is not responding to RMC Commands",
+"",
+"",
+"CPU fans 5/6 at maximum speed",
+"CPU fans 5/6 reduced speed from maximum",
+"PCI fans 1-4 at maximum speed",
+"PCI fans 1-4 reduced speed from maximum"
+};
+
+#define CLIPPER_ENV_FAN_MASK	0xF3FL
+
+static char *CLIPPER_EnvQW8POWER[] = {
+"Power Supply 0 AC input fail",
+"Power Supply 1 AC input fail",
+"Power Supply 2 AC input fail",
+"",
+"",
+"",
+"",
+"",
+"Power Supply 0 DC fail",
+"Power Supply 1 DC fail",
+"Power Supply 2 DC fail",
+"Vterm fail",
+"CPU0 Regulator fail",
+"CPU1 Regulator fail",
+"CPU2 Regulator fail",
+"CPU3 Regulator fail",
+"",
+"No CPU in system motherboard CPU slot 0",
+"Invalid CPU SROM voltage setting or checksum",
+"TIG load initialization or sequence fail",
+"Over temperature fail",
+"CPU door open fail",
+"System fan 5 (CPU backup fan) fail",
+"Cterm fail"
+};
+
+#define CLIPPER_ENV_POWER_MASK	0xFEFF07L
-- 
2.45.3