From: Vikram Sharma <quic_vikramsa@quicinc.com>
To: <rfoss@kernel.org>, <todor.too@gmail.com>,
<bryan.odonoghue@linaro.org>, <mchehab@kernel.org>,
<robh@kernel.org>, <krzk+dt@kernel.org>, <conor+dt@kernel.org>,
<andersson@kernel.org>, <konradybcio@kernel.org>,
<hverkuil-cisco@xs4all.nl>, <cros-qcom-dts-watchers@chromium.org>,
<catalin.marinas@arm.com>, <will@kernel.org>
Cc: <linux-arm-kernel@lists.infradead.org>,
<quic_vikramsa@quicinc.com>, <linux-media@vger.kernel.org>,
<linux-arm-msm@vger.kernel.org>, <devicetree@vger.kernel.org>,
<linux-kernel@vger.kernel.org>,
"Suresh Vankadara" <quic_svankada@quicinc.com>
Subject: [PATCH RFC/WIP v2 7/9] media: qcom: camss: Add support for CSID for sa8775p
Date: Sun, 27 Apr 2025 12:31:33 +0530 [thread overview]
Message-ID: <20250427070135.884623-8-quic_vikramsa@quicinc.com> (raw)
In-Reply-To: <20250427070135.884623-1-quic_vikramsa@quicinc.com>
The CSID in sa8775p is version 690, This csid is different from
csid 780 w.r.t few bit-fields.
Co-developed-by: Suresh Vankadara <quic_svankada@quicinc.com>
Signed-off-by: Suresh Vankadara <quic_svankada@quicinc.com>
Signed-off-by: Vikram Sharma <quic_vikramsa@quicinc.com>
---
.../platform/qcom/camss/camss-csid-gen3.c | 31 +++-
drivers/media/platform/qcom/camss/camss.c | 151 ++++++++++++++++++
2 files changed, 175 insertions(+), 7 deletions(-)
diff --git a/drivers/media/platform/qcom/camss/camss-csid-gen3.c b/drivers/media/platform/qcom/camss/camss-csid-gen3.c
index b66105f7b901..4f9471523a08 100644
--- a/drivers/media/platform/qcom/camss/camss-csid-gen3.c
+++ b/drivers/media/platform/qcom/camss/camss-csid-gen3.c
@@ -48,8 +48,12 @@
#define CSID_CSI2_RX_IRQ_CLEAR 0xA4
#define CSID_CSI2_RX_IRQ_SET 0xA8
+#define IS_CSID_690(csid) (csid->camss->res->version ==\
+ CAMSS_8775P ? true : false)
#define CSID_BUF_DONE_IRQ_STATUS 0x8C
-#define BUF_DONE_IRQ_STATUS_RDI_OFFSET (csid_is_lite(csid) ? 1 : 14)
+#define BUF_DONE_IRQ_STATUS_RDI_OFFSET (csid_is_lite(csid) ?\
+ 1 : (IS_CSID_690(csid) ?\
+ 13 : 14))
#define CSID_BUF_DONE_IRQ_MASK 0x90
#define CSID_BUF_DONE_IRQ_CLEAR 0x94
#define CSID_BUF_DONE_IRQ_SET 0x98
@@ -62,6 +66,7 @@
#define CSID_CSI2_RX_CFG0 0x200
#define CSI2_RX_CFG0_NUM_ACTIVE_LANES 0
+#define CSI2_RX_CFG0_VC_MODE 3
#define CSI2_RX_CFG0_DL0_INPUT_SEL 4
#define CSI2_RX_CFG0_PHY_NUM_SEL 20
@@ -69,7 +74,9 @@
#define CSI2_RX_CFG1_ECC_CORRECTION_EN BIT(0)
#define CSI2_RX_CFG1_VC_MODE BIT(2)
-#define CSID_RDI_CFG0(rdi) (0x500 + 0x100 * (rdi))
+#define CSID_RDI_CFG0(rdi) (csid_is_lite(csid) && IS_CSID_690(csid) ?\
+ (0x300 + 0x100 * (rdi)) :\
+ (0x500 + 0x100 * (rdi)))
#define RDI_CFG0_TIMESTAMP_EN BIT(6)
#define RDI_CFG0_TIMESTAMP_STB_SEL BIT(8)
#define RDI_CFG0_DECODE_FORMAT 12
@@ -78,10 +85,14 @@
#define RDI_CFG0_DT_ID 27
#define RDI_CFG0_EN BIT(31)
-#define CSID_RDI_CTRL(rdi) (0x504 + 0x100 * (rdi))
+#define CSID_RDI_CTRL(rdi) (csid_is_lite(csid) && IS_CSID_690(csid) ?\
+ (0x304 + 0x100 * (rdi)) :\
+ (0x504 + 0x100 * (rdi)))
#define RDI_CTRL_START_CMD BIT(0)
-#define CSID_RDI_CFG1(rdi) (0x510 + 0x100 * (rdi))
+#define CSID_RDI_CFG1(rdi) (csid_is_lite(csid) && IS_CSID_690(csid) ?\
+ (0x310 + 0x100 * (rdi)) :\
+ (0x510 + 0x100 * (rdi)))
#define RDI_CFG1_DROP_H_EN BIT(5)
#define RDI_CFG1_DROP_V_EN BIT(6)
#define RDI_CFG1_CROP_H_EN BIT(7)
@@ -89,9 +100,12 @@
#define RDI_CFG1_PIX_STORE BIT(10)
#define RDI_CFG1_PACKING_FORMAT_MIPI BIT(15)
-#define CSID_RDI_IRQ_SUBSAMPLE_PATTERN(rdi) (0x548 + 0x100 * (rdi))
-#define CSID_RDI_IRQ_SUBSAMPLE_PERIOD(rdi) (0x54C + 0x100 * (rdi))
-
+#define CSID_RDI_IRQ_SUBSAMPLE_PATTERN(rdi) (csid_is_lite(csid) && IS_CSID_690(csid) ?\
+ (0x348 + 0x100 * (rdi)) :\
+ (0x548 + 0x100 * (rdi)))
+#define CSID_RDI_IRQ_SUBSAMPLE_PERIOD(rdi) (csid_is_lite(csid) && IS_CSID_690(csid) ?\
+ (0x34C + 0x100 * (rdi)) :\
+ (0x54C + 0x100 * (rdi)))
#define CSI2_RX_CFG0_PHY_SEL_BASE_IDX 1
static void __csid_configure_rx(struct csid_device *csid,
@@ -103,6 +117,9 @@ static void __csid_configure_rx(struct csid_device *csid,
val |= phy->lane_assign << CSI2_RX_CFG0_DL0_INPUT_SEL;
val |= (phy->csiphy_id + CSI2_RX_CFG0_PHY_SEL_BASE_IDX) << CSI2_RX_CFG0_PHY_NUM_SEL;
+ if (IS_CSID_690(csid) && (vc > 3))
+ val |= 1 << CSI2_RX_CFG0_VC_MODE;
+
writel(val, csid->base + CSID_CSI2_RX_CFG0);
val = CSI2_RX_CFG1_ECC_CORRECTION_EN;
diff --git a/drivers/media/platform/qcom/camss/camss.c b/drivers/media/platform/qcom/camss/camss.c
index 60279f3a47bf..ef7b06c9f258 100644
--- a/drivers/media/platform/qcom/camss/camss.c
+++ b/drivers/media/platform/qcom/camss/camss.c
@@ -2269,6 +2269,10 @@ static const struct camss_subdev_resources csiphy_res_8550[] = {
}
};
+static const struct resources_wrapper csid_wrapper_res_sa8775p = {
+ .reg = "csid_wrapper",
+};
+
static const struct resources_wrapper csid_wrapper_res_sm8550 = {
.reg = "csid_wrapper",
};
@@ -2554,6 +2558,153 @@ static const struct camss_subdev_resources csiphy_res_8775p[] = {
},
};
+static const struct camss_subdev_resources csid_res_8775p[] = {
+ /* CSID0 */
+ {
+ .regulators = {},
+
+ .clock = { "csid", "csiphy_rx"},
+ .clock_rate = {
+ { 400000000, 400000000},
+ { 400000000, 400000000}
+ },
+
+ .reg = { "csid0", "csid_top" },
+ .interrupt = { "csid0" },
+ .csid = {
+ .is_lite = false,
+ .hw_ops = &csid_ops_gen3,
+ .parent_dev_ops = &vfe_parent_dev_ops,
+ .formats = &csid_formats_gen2
+ }
+ },
+ /* CSID1 */
+ {
+ .regulators = {},
+
+ .clock = { "csid", "csiphy_rx"},
+ .clock_rate = {
+ { 400000000, 400000000},
+ { 400000000, 400000000}
+ },
+
+ .reg = { "csid1", "csid_top" },
+ .interrupt = { "csid1" },
+ .csid = {
+ .is_lite = false,
+ .hw_ops = &csid_ops_gen3,
+ .parent_dev_ops = &vfe_parent_dev_ops,
+ .formats = &csid_formats_gen2
+ }
+ },
+
+ /* CSID2 (lite) */
+ {
+ .regulators = {},
+
+ .clock = { "cpas_ife_lite", "vfe_lite_ahb",
+ "vfe_lite_csid", "vfe_lite_cphy_rx",
+ "vfe_lite"},
+ .clock_rate = {
+ { 0, 0, 400000000, 400000000, 0},
+ { 0, 0, 400000000, 480000000, 0}
+ },
+
+ .reg = { "csid_lite0" },
+ .interrupt = { "csid_lite0" },
+ .csid = {
+ .is_lite = true,
+ .hw_ops = &csid_ops_gen3,
+ .parent_dev_ops = &vfe_parent_dev_ops,
+ .formats = &csid_formats_gen2
+ }
+ },
+ /* CSID3 (lite) */
+ {
+ .regulators = {},
+
+ .clock = { "cpas_ife_lite", "vfe_lite_ahb",
+ "vfe_lite_csid", "vfe_lite_cphy_rx",
+ "vfe_lite"},
+ .clock_rate = {
+ { 0, 0, 400000000, 400000000, 0},
+ { 0, 0, 400000000, 480000000, 0}
+ },
+
+ .reg = { "csid_lite1" },
+ .interrupt = { "csid_lite1" },
+ .csid = {
+ .is_lite = true,
+ .hw_ops = &csid_ops_gen3,
+ .parent_dev_ops = &vfe_parent_dev_ops,
+ .formats = &csid_formats_gen2
+ }
+ },
+ /* CSID4 (lite) */
+ {
+ .regulators = {},
+
+ .clock = { "cpas_ife_lite", "vfe_lite_ahb",
+ "vfe_lite_csid", "vfe_lite_cphy_rx",
+ "vfe_lite"},
+ .clock_rate = {
+ { 0, 0, 400000000, 400000000, 0},
+ { 0, 0, 400000000, 480000000, 0}
+ },
+
+ .reg = { "csid_lite2" },
+ .interrupt = { "csid_lite2" },
+ .csid = {
+ .is_lite = true,
+ .hw_ops = &csid_ops_gen3,
+ .parent_dev_ops = &vfe_parent_dev_ops,
+ .formats = &csid_formats_gen2
+ }
+ },
+ /* CSID5 (lite) */
+ {
+ .regulators = {},
+
+ .clock = { "cpas_ife_lite", "vfe_lite_ahb",
+ "vfe_lite_csid", "vfe_lite_cphy_rx",
+ "vfe_lite"},
+ .clock_rate = {
+ { 0, 0, 400000000, 400000000, 0},
+ { 0, 0, 400000000, 480000000, 0}
+ },
+
+ .reg = { "csid_lite3" },
+ .interrupt = { "csid_lite3" },
+ .csid = {
+ .is_lite = true,
+ .hw_ops = &csid_ops_gen3,
+ .parent_dev_ops = &vfe_parent_dev_ops,
+ .formats = &csid_formats_gen2
+ }
+ },
+ /* CSID6 (lite) */
+ {
+ .regulators = {},
+
+ .clock = { "cpas_ife_lite", "vfe_lite_ahb",
+ "vfe_lite_csid", "vfe_lite_cphy_rx",
+ "vfe_lite"},
+ .clock_rate = {
+ { 0, 0, 400000000, 400000000, 0},
+ { 0, 0, 400000000, 480000000, 0}
+ },
+
+ .reg = { "csid_lite4" },
+ .interrupt = { "csid_lite4" },
+ .csid = {
+ .is_lite = true,
+ .hw_ops = &csid_ops_gen3,
+ .parent_dev_ops = &vfe_parent_dev_ops,
+ .formats = &csid_formats_gen2
+ }
+ },
+};
+
static const struct resources_icc icc_res_sa8775p[] = {
{
.name = "ahb",
--
2.25.1
next prev parent reply other threads:[~2025-04-27 7:03 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-04-27 7:01 [PATCH v2 RFC/WIP 0/9] Add sa8775p camss support Vikram Sharma
2025-04-27 7:01 ` [PATCH RFC/WIP v2 1/9] media: qcom: camss: add generic csid handling in csid gen3 Vikram Sharma
2025-04-27 7:01 ` [PATCH RFC/WIP v2 2/9] media: qcom: camss: add generic vfe handling in vfe gen3 Vikram Sharma
2025-04-27 7:01 ` [PATCH RFC/WIP v2 3/9] media: dt-bindings: Add qcom,sa8775p-camss Vikram Sharma
2025-04-28 7:38 ` Krzysztof Kozlowski
2025-04-27 7:01 ` [PATCH RFC/WIP v2 4/9] arm64: dts: qcom: sa8775p: Add support for camss Vikram Sharma
2025-04-30 10:30 ` Konrad Dybcio
2025-05-10 7:14 ` Suresh Vankadara
2025-05-11 9:53 ` Bryan O'Donoghue
2025-04-27 7:01 ` [PATCH RFC/WIP v2 5/9] media: qcom: camss: Add sa8775p compatible Vikram Sharma
2025-05-10 7:25 ` Suresh Vankadara
2025-04-27 7:01 ` [PATCH RFC/WIP v2 6/9] media: qcom: camss: Add support for CSIPHY 690 Vikram Sharma
2025-04-27 7:01 ` Vikram Sharma [this message]
2025-05-10 7:58 ` [PATCH RFC/WIP v2 7/9] media: qcom: camss: Add support for CSID for sa8775p Suresh Vankadara
2025-04-27 7:01 ` [PATCH RFC/WIP v2 8/9] media: qcom: camss: Add support for VFE 690 Vikram Sharma
2025-04-27 7:01 ` [PATCH RFC/WIP v2 9/9] media: qcom: camss: Enumerate resources for SA8775P Vikram Sharma
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20250427070135.884623-8-quic_vikramsa@quicinc.com \
--to=quic_vikramsa@quicinc.com \
--cc=andersson@kernel.org \
--cc=bryan.odonoghue@linaro.org \
--cc=catalin.marinas@arm.com \
--cc=conor+dt@kernel.org \
--cc=cros-qcom-dts-watchers@chromium.org \
--cc=devicetree@vger.kernel.org \
--cc=hverkuil-cisco@xs4all.nl \
--cc=konradybcio@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=mchehab@kernel.org \
--cc=quic_svankada@quicinc.com \
--cc=rfoss@kernel.org \
--cc=robh@kernel.org \
--cc=todor.too@gmail.com \
--cc=will@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®