[PATCH RESEND v4 2/4] arm64: dts: qcom: sdm845-xiaomi-beryllium-common: add touchscreen related nodes

[Joel Selvaraj via B4 Relay <devnull+foss.joelselvaraj.com@kernel.org>]

From: Joel Selvaraj <foss@joelselvaraj.com>

Enable qupv3_id_1 and gpi_dma1 as they are required for configuring
touchscreen. Also add pinctrl configurations needed for touchscreen.
These are common for both the tianma and ebbg touchscreen variant.
In the subsequent patches, we will enable support for the Novatek NT36672a
touchscreen and FocalTech FT8719 touchscreen that are used in the Poco F1
Tianma and EBBG panel variant respectively. This is done in preparation
for that.

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Joel Selvaraj <foss@joelselvaraj.com>
---
 .../dts/qcom/sdm845-xiaomi-beryllium-common.dtsi   | 39 ++++++++++++++++++++++
 1 file changed, 39 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi
index 617b17b2d7d9dfb686445e02cfc8f97de5b6f7a6..e93ed6effdd7384c750e671a2bc1be3a472c54f8 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi
@@ -243,6 +243,10 @@ &gmu {
 	status = "okay";
 };
 
+&gpi_dma1 {
+	status = "okay";
+};
+
 &gpu {
 	status = "okay";
 
@@ -408,6 +412,10 @@ &qupv3_id_0 {
 	status = "okay";
 };
 
+&qupv3_id_1 {
+	status = "okay";
+};
+
 &sdhc_2 {
 	status = "okay";
 
@@ -513,6 +521,37 @@ sdc2_card_det_n: sd-card-det-n-state {
 		function = "gpio";
 		bias-pull-up;
 	};
+
+	ts_int_default: ts-int-default-state {
+		pins = "gpio31";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-pull-down;
+		output-disable;
+	};
+
+	ts_reset_default: ts-reset-default-state {
+		pins = "gpio32";
+		function = "gpio";
+		drive-strength = <16>;
+		output-high;
+	};
+
+	ts_int_sleep: ts-int-sleep-state {
+		pins = "gpio31";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+		output-disable;
+	};
+
+	ts_reset_sleep: ts-reset-sleep-state {
+		pins = "gpio32";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
 };
 
 &uart6 {

-- 
2.49.0