Re: [PATCH v4 0/2] Support for Texas Instruments TPS6131X flash LED driver

[Lee Jones <lee@kernel.org>]

On Fri, 09 May 2025, Matthias Fend wrote:

> The TPS61310/TPS61311 is a flash LED driver with I2C interface. Its power
> stage is capable of supplying a maximum total current of roughly 1500mA.
> The TPS6131x provides three constant-current sinks, capable of sinking up
> to 2 × 400mA (LED1 and LED3) and 800mA (LED2) in flash mode. In torch mode
> each sink (LED1, LED2, LED3) supports currents up to 175m
> 
> Signed-off-by: Matthias Fend <matthias.fend@emfend.at>
> ---
> Changes in v4:
> - Added/removed/adjusted comments
> - Use defines for register defaults
> - Updated source format
> - Check for error in torch refresh timer
> - Return error from tps6131x_parse_node()
> - Link to v3: https://lore.kernel.org/r/20250423-leds-tps6131x-v3-0-ca67d346a4ea@emfend.at
> 
> Changes in v3:
> - Add comment for locking
> - Drop handling based on CONFIG_V4L2_FLASH_LED_CLASS
> - Stop if getting reset GPIO fails
> - Optimize locks
> - Fix type of num_channels (u32 -> int)
> - Convert a remaining return sequence to dev_err_probe
> - Link to v2: https://lore.kernel.org/r/20250318-leds-tps6131x-v2-0-bc09c7a50b2e@emfend.at
> 
> Changes in v2:
> - Bindings: Extend device description
> - Bindings: Drop unused address/size cells
> - Bindings: Use fallback compatible 
> - Bindings: Corrected minimum current for 50mA steps
> - Bindings: Drop node label
> - Fix name of REGISTER4 INDC shift define
> - Save device instead i2c_client in private data
> - Add comment for mutex
> - Use macro to convert from uA to mA
> - Use defines to describe initial register values
> - Add safety delay during reset sequence
> - Use fixed value enum to set the mode
> - Renamed some local variables
> - Re-sorted local variables
> - Replaced ifdefs for V4L2_FLASH_LED_CLASS
> - Improved some error messages
> - Link to v1: https://lore.kernel.org/r/20250228-leds-tps6131x-v1-0-d1071d90f9ea@emfend.at
> 
> ---
> Matthias Fend (2):
>       dt-bindings: leds: add Texas Instruments TPS6131x flash LED driver
>       leds: tps6131x: add support for Texas Instruments TPS6131X flash LED driver
> 
>  .../devicetree/bindings/leds/ti,tps61310.yaml      | 120 +++
>  MAINTAINERS                                        |   7 +
>  drivers/leds/flash/Kconfig                         |  11 +
>  drivers/leds/flash/Makefile                        |   1 +
>  drivers/leds/flash/leds-tps6131x.c                 | 815 +++++++++++++++++++++
>  5 files changed, 954 insertions(+)

I get errors on apply:

  WARNING: Message contains suspicious unicode control characters!
         Subject: [PATCH v4 2/2] leds: tps6131x: add support for Texas Instruments TPS6131X flash LED driver
            Line: + * Register contents after a power on/reset. These values ​​cannot be changed.
            -----------------------------------------------------------------^
            Char: ZERO WIDTH SPACE (0x200b)
         If you are sure about this, rerun with the right flag to allow.

FWIW, I also saw these in your mails:

  > The values <200b><200b>are fixed because they are written directly to a register.
  > In V1, I used an enum without values <200b><200b>and mapped it to the register value in
  > a function. I was asked to omit this mapping and use the enum directly.

Never seen this before.  Not sure what's going on.

Please fix and resubmit.

-- 
Lee Jones [李琼斯]