From: Frank Li <Frank.Li@nxp.com>
To: Linus Walleij <linus.walleij@linaro.org>,
Bartosz Golaszewski <brgl@bgdev.pl>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
linux-gpio@vger.kernel.org (open list:GPIO SUBSYSTEM),
devicetree@vger.kernel.org (open list:OPEN FIRMWARE AND
FLATTENED DEVICE TREE BINDINGS),
linux-kernel@vger.kernel.org (open list)
Cc: imx@lists.linux.dev
Subject: [PATCH 1/1] dt-bindings: gpio: convert gpio-pisosr.txt to yaml format
Date: Thu, 22 May 2025 18:37:41 -0400 [thread overview]
Message-ID: <20250522223742.516254-1-Frank.Li@nxp.com> (raw)
Covert gpio-pisosr.txt to yaml format.
Additional changes:
- Add ref to spi-peripheral-props.yaml.
- Set ngpios max value to 32.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
.../devicetree/bindings/gpio/gpio-pisosr.txt | 34 ----------
.../devicetree/bindings/gpio/pisosr-gpio.yaml | 67 +++++++++++++++++++
2 files changed, 67 insertions(+), 34 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/gpio/gpio-pisosr.txt
create mode 100644 Documentation/devicetree/bindings/gpio/pisosr-gpio.yaml
diff --git a/Documentation/devicetree/bindings/gpio/gpio-pisosr.txt b/Documentation/devicetree/bindings/gpio/gpio-pisosr.txt
deleted file mode 100644
index fba3c61f6a5bc..0000000000000
--- a/Documentation/devicetree/bindings/gpio/gpio-pisosr.txt
+++ /dev/null
@@ -1,34 +0,0 @@
-Generic Parallel-in/Serial-out Shift Register GPIO Driver
-
-This binding describes generic parallel-in/serial-out shift register
-devices that can be used for GPI (General Purpose Input). This includes
-SN74165 serial-out shift registers and the SN65HVS88x series of
-industrial serializers.
-
-Required properties:
- - compatible : Should be "pisosr-gpio".
- - gpio-controller : Marks the device node as a GPIO controller.
- - #gpio-cells : Should be two. For consumer use see gpio.txt.
-
-Optional properties:
- - ngpios : Number of used GPIO lines (0..n-1), default is 8.
- - load-gpios : GPIO pin specifier attached to load enable, this
- pin is pulsed before reading from the device to
- load input pin values into the device.
-
-For other required and optional properties of SPI slave
-nodes please refer to ../spi/spi-bus.txt.
-
-Example:
-
- gpio@0 {
- compatible = "ti,sn65hvs882", "pisosr-gpio";
- gpio-controller;
- #gpio-cells = <2>;
-
- load-gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
-
- reg = <0>;
- spi-max-frequency = <1000000>;
- spi-cpol;
- };
diff --git a/Documentation/devicetree/bindings/gpio/pisosr-gpio.yaml b/Documentation/devicetree/bindings/gpio/pisosr-gpio.yaml
new file mode 100644
index 0000000000000..db98ba413fb6b
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/pisosr-gpio.yaml
@@ -0,0 +1,67 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/gpio/pisosr-gpio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Generic Parallel-in/Serial-out Shift Register GPIO Driver
+
+description:
+ This binding describes generic parallel-in/serial-out shift register
+ devices that can be used for GPI (General Purpose Input). This includes
+ SN74165 serial-out shift registers and the SN65HVS88x series of
+ industrial serializers.
+
+maintainers:
+ - Frank Li <Frank.Li@nxp.com>
+
+properties:
+ compatible:
+ enum:
+ - pisosr-gpio
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ const: 2
+
+ ngpios:
+ maximum: 32
+ default: 8
+
+ load-gpios:
+ description:
+ GPIO pin specifier attached to load enable, this
+ pin is pulsed before reading from the device to
+ load input pin values into the device.
+
+ spi-cpol: true
+
+required:
+ - compatible
+ - gpio-controller
+ - '#gpio-cells'
+
+allOf:
+ - $ref: /schemas/spi/spi-peripheral-props.yaml#
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+
+ spi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpio@0 {
+ compatible = "pisosr-gpio";
+ reg = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ load-gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+ spi-max-frequency = <1000000>;
+ spi-cpol;
+ };
+ };
--
2.34.1
next reply other threads:[~2025-05-22 22:38 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-05-22 22:37 Frank Li [this message]
2025-05-27 18:08 ` Rob Herring (Arm)
2025-06-10 8:11 ` Bartosz Golaszewski
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20250522223742.516254-1-Frank.Li@nxp.com \
--to=frank.li@nxp.com \
--cc=brgl@bgdev.pl \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=imx@lists.linux.dev \
--cc=krzk+dt@kernel.org \
--cc=linus.walleij@linaro.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®