From: binarycraft007 <elliot.huang.signed@gmail.com>
To: andersson@kernel.org
Cc: conor+dt@kernel.org, devicetree@vger.kernel.org,
johan@kernel.org, konrad.dybcio@oss.qualcomm.com,
konradybcio@kernel.org, krzk+dt@kernel.org,
linux-arm-msm@vger.kernel.org, linux-kernel@vger.kernel.org,
lumag@kernel.org, maud_spierings@hotmail.com, robh@kernel.org,
Elliot Huang <elliot.huang.signed@gmail.com>
Subject: [PATCH 1/1] arm64: dts: qcom: support sound on Asus Vivobook S15
Date: Mon, 2 Jun 2025 16:16:38 +0800 [thread overview]
Message-ID: <20250602081638.51724-1-elliot.huang.signed@gmail.com> (raw)
In-Reply-To: <174770727723.36693.13352978360096773573.b4-ty@kernel.org>
From: Elliot Huang <elliot.huang.signed@gmail.com>
This adds sound support for vivobook s15, tested:
- 2 speakers.
- 2 dmics
- headset with mic(distorted).
Signed-off-by: Elliot Huang <elliot.huang.signed@gmail.com>
---
.../dts/qcom/x1e80100-asus-vivobook-s15.dts | 202 ++++++++++++++++++
1 file changed, 202 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/x1e80100-asus-vivobook-s15.dts b/arch/arm64/boot/dts/qcom/x1e80100-asus-vivobook-s15.dts
index 71b2cc6..cce2460 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100-asus-vivobook-s15.dts
+++ b/arch/arm64/boot/dts/qcom/x1e80100-asus-vivobook-s15.dts
@@ -23,6 +23,32 @@ aliases {
serial1 = &uart14;
};
+ wcd938x: audio-codec {
+ compatible = "qcom,wcd9385-codec";
+
+ pinctrl-0 = <&wcd_default>;
+ pinctrl-names = "default";
+
+ qcom,micbias1-microvolt = <1800000>;
+ qcom,micbias2-microvolt = <1800000>;
+ qcom,micbias3-microvolt = <1800000>;
+ qcom,micbias4-microvolt = <1800000>;
+ qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
+ qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+ qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
+ qcom,rx-device = <&wcd_rx>;
+ qcom,tx-device = <&wcd_tx>;
+
+ reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>;
+
+ vdd-buck-supply = <&vreg_l15b_1p8>;
+ vdd-rxtx-supply = <&vreg_l15b_1p8>;
+ vdd-io-supply = <&vreg_l15b_1p8>;
+ vdd-mic-bias-supply = <&vreg_bob1>;
+
+ #sound-dai-cells = <1>;
+ };
+
gpio-keys {
compatible = "gpio-keys";
pinctrl-0 = <&hall_int_n_default>;
@@ -105,6 +131,88 @@ pmic_glink_ss1_ss_in: endpoint {
};
};
+ sound {
+ compatible = "qcom,x1e80100-sndcard";
+ model = "X1E80100-ASUS-Vivobook-S15";
+ audio-routing = "SpkrLeft IN", "WSA WSA_SPK1 OUT",
+ "SpkrRight IN", "WSA WSA_SPK2 OUT",
+ "IN1_HPHL", "HPHL_OUT",
+ "IN2_HPHR", "HPHR_OUT",
+ "AMIC2", "MIC BIAS2",
+ "VA DMIC0", "MIC BIAS3",
+ "VA DMIC1", "MIC BIAS3",
+ "VA DMIC0", "VA MIC BIAS3",
+ "VA DMIC1", "VA MIC BIAS3",
+ "TX SWR_INPUT1", "ADC2_OUTPUT";
+
+ va-dai-link {
+ link-name = "VA Capture";
+
+ cpu {
+ sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
+ };
+
+ codec {
+ sound-dai = <&lpass_vamacro 0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+
+ wcd-capture-dai-link {
+ link-name = "WCD Capture";
+
+ cpu {
+ sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
+ };
+
+ codec {
+ sound-dai = <&wcd938x 1>, <&swr2 1>,
+ <&lpass_txmacro 0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+
+ wcd-playback-dai-link {
+ link-name = "WCD Playback";
+
+ cpu {
+ sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
+ };
+
+ codec {
+ sound-dai = <&wcd938x 0>, <&swr1 0>,
+ <&lpass_rxmacro 0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+
+ wsa-dai-link {
+ link-name = "WSA Playback";
+
+ cpu {
+ sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
+ };
+
+ codec {
+ sound-dai = <&left_spkr>, <&right_spkr>,
+ <&swr0 0>, <&lpass_wsamacro 0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+ };
+
reserved-memory {
linux,cma {
compatible = "shared-dma-pool";
@@ -290,6 +398,13 @@ vreg_bob2: bob2 {
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
+ vreg_l1b_1p8: ldo1 {
+ regulator-name = "vreg_l1b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
vreg_l2b_3p0: ldo2 {
regulator-name = "vreg_l2b_3p0";
regulator-min-microvolt = <3072000>;
@@ -304,6 +419,14 @@ vreg_l4b_1p8: ldo4 {
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
+ vreg_l12b_1p2: ldo12 {
+ regulator-name = "vreg_l12b_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-always-on;
+ };
+
vreg_l13b_3p0: ldo13 {
regulator-name = "vreg_l13b_3p0";
regulator-min-microvolt = <3072000>;
@@ -586,6 +709,24 @@ &i2c7 {
/* PS8830 USB4 Retimer? @ 0x8 */
};
+&lpass_tlmm {
+ spkr_01_sd_n_active: spkr-01-sd-n-active-state {
+ pins = "gpio12";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-low;
+ };
+};
+
+&lpass_vamacro {
+ pinctrl-0 = <&dmic01_default>;
+ pinctrl-names = "default";
+
+ vdd-micb-supply = <&vreg_l1b_1p8>;
+ qcom,dmic-sample-rate = <4800000>;
+};
+
&mdss {
status = "okay";
};
@@ -742,6 +883,59 @@ &smb2360_1_eusb2_repeater {
vdd3-supply = <&vreg_l14b_3p0>;
};
+&swr0 {
+ status = "okay";
+
+ pinctrl-0 = <&wsa_swr_active>, <&spkr_01_sd_n_active>;
+ pinctrl-names = "default";
+
+ /* WSA8845, Left Speaker */
+ left_spkr: speaker@0,0 {
+ compatible = "sdw20217020400";
+ reg = <0 0>;
+ reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "SpkrLeft";
+ vdd-1p8-supply = <&vreg_l15b_1p8>;
+ vdd-io-supply = <&vreg_l12b_1p2>;
+ qcom,port-mapping = <1 2 3 7 10 13>;
+ };
+
+ /* WSA8845, Right Speaker */
+ right_spkr: speaker@0,1 {
+ compatible = "sdw20217020400";
+ reg = <0 1>;
+ reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "SpkrRight";
+ vdd-1p8-supply = <&vreg_l15b_1p8>;
+ vdd-io-supply = <&vreg_l12b_1p2>;
+ qcom,port-mapping = <4 5 6 7 11 13>;
+ };
+};
+
+&swr1 {
+ status = "okay";
+
+ /* WCD9385 RX */
+ wcd_rx: codec@0,4 {
+ compatible = "sdw20217010d00";
+ reg = <0 4>;
+ qcom,rx-port-mapping = <1 2 3 4 5>;
+ };
+};
+
+&swr2 {
+ status = "okay";
+
+ /* WCD9385 TX */
+ wcd_tx: codec@0,3 {
+ compatible = "sdw20217010d00";
+ reg = <0 3>;
+ qcom,tx-port-mapping = <2 2 3 4>;
+ };
+};
+
&tlmm {
gpio-reserved-ranges = <34 2>, /* Unused */
<44 4>, /* SPI (TPM) */
@@ -849,6 +1043,14 @@ tpad_default: tpad-default-state {
bias-disable;
};
+ wcd_default: wcd-reset-n-active-state {
+ pins = "gpio191";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-low;
+ };
+
wcn_bt_en: wcn-bt-en-state {
pins = "gpio116";
function = "gpio";
--
2.49.0
next prev parent reply other threads:[~2025-06-02 8:20 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-03-28 18:46 [PATCH v7] arm64: dts: qcom: x1e80100-vivobook-s15: Add bluetooth Maud Spierings via B4 Relay
2025-05-20 2:14 ` Bjorn Andersson
2025-06-02 8:16 ` binarycraft007 [this message]
2025-06-02 8:27 ` [PATCH 1/1] arm64: dts: qcom: support sound on Asus Vivobook S15 Krzysztof Kozlowski
2025-06-02 8:30 ` Elliot Huang
2025-06-02 10:00 ` Krzysztof Kozlowski
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20250602081638.51724-1-elliot.huang.signed@gmail.com \
--to=elliot.huang.signed@gmail.com \
--cc=andersson@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=johan@kernel.org \
--cc=konrad.dybcio@oss.qualcomm.com \
--cc=konradybcio@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=lumag@kernel.org \
--cc=maud_spierings@hotmail.com \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®