[PATCH v3 1/7] gpu: nova-core: Add code comments related to devinit

[Alexandre Courbot <acourbot@nvidia.com>]

From: Joel Fernandes <joelagnelf@nvidia.com>

Add several code comments to reduce acronym soup and explain how devinit
magic and bootflow works before driver loads. These are essential for
debug and development of the nova driver.

[acourbot@nvidia.com: reformat and reword a couple of sentences]

Signed-off-by: Joel Fernandes <joelagnelf@nvidia.com>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
---
 drivers/gpu/nova-core/gfw.rs  | 39 +++++++++++++++++++++++++++++++++++----
 drivers/gpu/nova-core/regs.rs | 16 ++++++++++++++--
 2 files changed, 49 insertions(+), 6 deletions(-)

diff --git a/drivers/gpu/nova-core/gfw.rs b/drivers/gpu/nova-core/gfw.rs
index d5b68e02d405750b18d634d772f15f413453e80d..8ac1ed18719926493369c2aae9a59b2b55fa2b12 100644
--- a/drivers/gpu/nova-core/gfw.rs
+++ b/drivers/gpu/nova-core/gfw.rs
@@ -1,10 +1,22 @@
 // SPDX-License-Identifier: GPL-2.0
 
-//! GPU Firmware (GFW) support.
+//! GPU Firmware (`GFW`) support, a.k.a `devinit`.
 //!
 //! Upon reset, the GPU runs some firmware code from the BIOS to setup its core parameters. Most of
 //! the GPU is considered unusable until this step is completed, so we must wait on it before
 //! performing driver initialization.
+//!
+//! A clarification about devinit terminology: devinit is a sequence of register read/writes after
+//! reset that performs tasks such as:
+//! 1. Programming VRAM memory controller timings.
+//! 2. Power sequencing.
+//! 3. Clock and PLL configuration.
+//! 4. Thermal management.
+//!
+//! devinit itself is a 'script' which is interpreted by an interpreter program typically running
+//! on the PMU microcontroller.
+//!
+//! Note that the devinit sequence also needs to run during suspend/resume.
 
 use kernel::bindings;
 use kernel::prelude::*;
@@ -14,13 +26,32 @@
 use crate::regs;
 use crate::util;
 
-/// Wait until `GFW` (GPU Firmware) completes, or a 4 seconds timeout elapses.
+/// Wait for the `GFW` (GPU firmware) boot completion signal (`GFW_BOOT`), or a 4 seconds timeout.
+///
+/// Upon GPU reset, several microcontrollers (such as PMU, SEC2, GSP etc) run some firmware code to
+/// setup its core parameters. Most of the GPU is considered unusable until this step is completed,
+/// so it must be waited on very early during driver initialization.
+///
+/// The `GFW` code includes several components that need to execute before the driver loads. These
+/// components are located in the VBIOS ROM and executed in a sequence on these different
+/// microcontrollers. The devinit sequence typically runs on the PMU, and the FWSEC runs on the
+/// GSP.
+///
+/// This function waits for a signal indicating that core initialization is complete. Before this
+/// signal is received, little can be done with the GPU. This signal is set by the FWSEC running on
+/// the GSP in Heavy-secured mode.
 pub(crate) fn wait_gfw_boot_completion(bar: &Bar0) -> Result {
+    // Before accessing the completion status in `NV_PGC6_AON_SECURE_SCRATCH_GROUP_05`, we must
+    // first check `NV_PGC6_AON_SECURE_SCRATCH_GROUP_05_PRIV_LEVEL_MASK`. This is because
+    // `NV_PGC6_AON_SECURE_SCRATCH_GROUP_05` becomes accessible only after the secure firmware
+    // (FWSEC) lowers the privilege level to allow CPU (LS/Light-secured) access. We can only
+    // safely read the status register from CPU (LS/Light-secured) once the mask indicates
+    // that the privilege level has been lowered.
+    //
     // TIMEOUT: arbitrarily large value. GFW starts running immediately after the GPU is put out of
     // reset, and should complete in less time than that.
     util::wait_on(Delta::from_secs(4), || {
-        // Check that FWSEC has lowered its protection level before reading the GFW_BOOT
-        // status.
+        // Check that FWSEC has lowered its protection level before reading the GFW_BOOT status.
         let gfw_booted = regs::NV_PGC6_AON_SECURE_SCRATCH_GROUP_05_PRIV_LEVEL_MASK::read(bar)
             .read_protection_level0()
             && regs::NV_PGC6_AON_SECURE_SCRATCH_GROUP_05_0_GFW_BOOT::read(bar).completed();
diff --git a/drivers/gpu/nova-core/regs.rs b/drivers/gpu/nova-core/regs.rs
index e8b8aabce3f36abe6a7fba3e11f677e36baa3897..ce08fab8fa96fcacf6947512ebdf4975ebd8772c 100644
--- a/drivers/gpu/nova-core/regs.rs
+++ b/drivers/gpu/nova-core/regs.rs
@@ -104,9 +104,21 @@ pub(crate) fn higher_bound(self) -> u64 {
     }
 }
 
-/* PGC6 */
+/*
+ * PGC6 register space.
+ *
+ * `GC6` is a GPU low-power state where VRAM is in self-refresh and the GPU is powered down (except
+ * for power rails needed to keep self-refresh working and important registers and hardware
+ * blocks).
+ *
+ * These scratch registers remain powered on even in a low-power state and have a designated group
+ * number.
+ */
 
-register!(NV_PGC6_AON_SECURE_SCRATCH_GROUP_05_PRIV_LEVEL_MASK @ 0x00118128 {
+// Privilege level mask register. It dictates whether the host CPU has privilege to access the
+// `PGC6_AON_SECURE_SCRATCH_GROUP_05` register (which it needs to read GFW_BOOT).
+register!(NV_PGC6_AON_SECURE_SCRATCH_GROUP_05_PRIV_LEVEL_MASK @ 0x00118128,
+          "Privilege level mask register" {
     0:0     read_protection_level0 as bool, "Set after FWSEC lowers its protection level";
 });
 

-- 
2.50.0