[PATCH v2 2/3] arm64: dts: ti: Add support for Variscite VAR-SOM-AM62P

[Stefano Radaelli <stefano.radaelli21@gmail.com>]

Add device tree support for the Variscite VAR-SOM-AM62P system on module.
This SOM is designed to be used with various carrier boards.

The module includes:
- AM62Px Sitara MPU processor
- Up to 8GB of DDR4-3733 memory
- eMMC storage memory
- PS6522430 chip as a Power Management Integrated circuit (PMIC)
- Integrated 10/100/1000 Mbps Ethernet Transceiver Analog Devices ADIN1300
- Resistive touch panel interface controller TI TSC2046
- I2C interfaces

Only SOM-specific peripherals are enabled by default. Carrier board
specific interfaces are left disabled to be enabled in the respective
carrier board device trees.

Link: https://www.variscite.it/product/system-on-module-som/cortex-a53-krait/var-som-am62p-ti-sitara-am62px/

Signed-off-by: Stefano Radaelli <stefano.radaelli21@gmail.com>
---
v2:
 - Fixed warnings and cleanup

 arch/arm64/boot/dts/ti/k3-am62p5-var-som.dtsi | 374 ++++++++++++++++++
 1 file changed, 374 insertions(+)
 create mode 100644 arch/arm64/boot/dts/ti/k3-am62p5-var-som.dtsi

diff --git a/arch/arm64/boot/dts/ti/k3-am62p5-var-som.dtsi b/arch/arm64/boot/dts/ti/k3-am62p5-var-som.dtsi
new file mode 100644
index 000000000000..a12522e554fe
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am62p5-var-som.dtsi
@@ -0,0 +1,374 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Common dtsi for Variscite VAR-SOM-AM62P
+ *
+ * Copyright (C) 2021-2022 Texas Instruments Incorporated - https://www.ti.com/
+ * Copyright (C) 2025 Variscite Ltd. - https://www.variscite.com/
+ *
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pwm/pwm.h>
+#include "k3-am62p5.dtsi"
+
+/ {
+	compatible = "variscite,am62p-var-som", "ti,am62p5";
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		post-power-on-delay-ms = <100>;
+		power-off-delay-us = <10000>;
+		reset-gpios = <&main_gpio0 54 GPIO_ACTIVE_LOW>,	/* WIFI_PWR_EN */
+			      <&main_gpio0 59 GPIO_ACTIVE_LOW>;	/* WIFI_EN */
+	};
+
+	mmc_pwrseq: mmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_mmc_pwrseq>;
+		reset-gpios = <&main_gpio0 49 GPIO_ACTIVE_LOW>;
+	};
+
+	memory@80000000 {
+		/* 8G RAM */
+		reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
+		      <0x00000008 0x80000000 0x00000001 0x80000000>;
+		device_type = "memory";
+		bootph-pre-ram;
+	};
+
+	opp-table {
+		/* Add 1.4GHz OPP for am62p5-sk board. Requires VDD_CORE at 0v85 */
+		opp-1400000000 {
+			opp-hz = /bits/ 64 <1400000000>;
+			opp-supported-hw = <0x01 0x0004>;
+			clock-latency-ns = <6000000>;
+		};
+	};
+
+	reserved_memory: reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		rtos_ipc_memory_region: rtos-ipc-memory@9b500000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x9b500000 0x00 0x00300000>;
+			no-map;
+		};
+
+		mcu_r5fss0_core0_dma_memory_region: mcu-r5fss-dma-memory-region@9b800000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x9b800000 0x00 0x00100000>;
+			no-map;
+		};
+
+		mcu_r5fss0_core0_memory_region: mcu-r5fss-memory-region@9b900000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x9b900000 0x00 0x00f00000>;
+			no-map;
+		};
+
+		wkup_r5fss0_core0_dma_memory_region: r5f-dma-memory@9c800000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x9c800000 0x00 0x00100000>;
+			no-map;
+		};
+
+		wkup_r5fss0_core0_memory_region: r5f-memory@9c900000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x9c900000 0x00 0x01e00000>;
+			no-map;
+		};
+
+		secure_tfa_ddr: tfa@9e780000 {
+			reg = <0x00 0x9e780000 0x00 0x80000>;
+			no-map;
+		};
+
+		secure_ddr: optee@9e800000 {
+			reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */
+			no-map;
+		};
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "On-module +V3.3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	reg_1v8: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "On-module +V1.8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&reg_3v3>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	reg_3v3_phy: regulator-3v3-phy {
+		compatible = "regulator-fixed";
+		regulator-name = "On-module +V3.3_PHY";
+		gpios = <&main_gpio0 45 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+		status="okay";
+	};
+};
+
+&cpsw3g {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii1>;
+};
+
+&cpsw3g_mdio {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_mdio1>;
+	cpsw3g_phy0: ethernet-phy@4 {
+		reg = <4>;
+		compatible = "ethernet-phy-id0283.bc30";
+		reset-gpios = <&main_gpio0 46 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10000>;
+		reset-deassert-us = <100000>;
+	};
+};
+
+&cpsw_port1 {
+	/*
+	 * The required RGMII TX and RX 2ns delays are implemented directly
+	 * in hardware via passive delay elements on the SOM PCB.
+	 * No delay configuration is needed in software via PHY driver.
+	 */
+	phy-mode = "rgmii";
+	phy-handle = <&cpsw3g_phy0>;
+	status = "okay";
+};
+
+&main_i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	clock-frequency = <400000>;
+	status = "okay";
+};
+
+&main_i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	clock-frequency = <400000>;
+	status = "okay";
+};
+
+&main_pmx0 {
+	pinctrl_mmc_pwrseq: main-emmc-pwrseq-pins {
+		pinctrl-single,pins = <
+			AM62PX_IOPAD(0x00c8, PIN_OUTPUT, 7) /* (AB23) VOUT0_DATA4.GPIO0_49 */
+		>;
+	};
+
+	pinctrl_i2c2: main-i2c2-default-pins {
+		pinctrl-single,pins = <
+			AM62PX_IOPAD(0x00b0, PIN_INPUT_PULLUP, 1) /* (T22) GPMC0_CSn2.I2C2_SCL */
+			AM62PX_IOPAD(0x00b4, PIN_INPUT_PULLUP, 1) /* (U25) GPMC0_CSn3.I2C2_SDA */
+		>;
+	};
+
+	pinctrl_i2c3: main-i2c3-default-pins {
+		pinctrl-single,pins = <
+			AM62PX_IOPAD(0x01d0, PIN_INPUT_PULLUP, 2) /* (A23) UART0_CTSn.I2C3_SCL */
+			AM62PX_IOPAD(0x01d4, PIN_INPUT_PULLUP, 2) /* (C22) UART0_RTSn.I2C3_SDA */
+		>;
+	};
+
+	pinctrl_mcasp1: main-mcasp1-default-pins {
+		pinctrl-single,pins = <
+			AM62PX_IOPAD(0x0090, PIN_INPUT, 2) /* (U24) GPMC0_BE0n_CLE.MCASP1_ACLKX */
+			AM62PX_IOPAD(0x0098, PIN_INPUT, 2) /* (AA24) GPMC0_WAIT0.MCASP1_AFSX */
+			AM62PX_IOPAD(0x008c, PIN_OUTPUT, 2) /* (T25) GPMC0_WEn.MCASP1_AXR0 */
+			AM62PX_IOPAD(0x0084, PIN_INPUT, 2) /* (R25) GPMC0_ADVn_ALE.MCASP1_AXR2 */
+			AM62PX_IOPAD(0x00a0, PIN_OUTPUT, 1) /* (P24) GPMC0_WPn.AUDIO_EXT_REFCLK1 */
+		>;
+	};
+
+	pinctrl_mdio1: main-mdio1-default-pins {
+		pinctrl-single,pins = <
+			AM62PX_IOPAD(0x0160, PIN_OUTPUT, 0) /* (F17) MDIO0_MDC */
+			AM62PX_IOPAD(0x015c, PIN_INPUT, 0) /* (F16) MDIO0_MDIO */
+		>;
+	};
+
+	pinctrl_mmc2: main-mmc2-default-pins {
+		pinctrl-single,pins = <
+			AM62PX_IOPAD(0x0120, PIN_INPUT_PULLUP, 0) /* (K24) MMC2_CMD */
+			AM62PX_IOPAD(0x0118, PIN_INPUT_PULLDOWN, 0) /* (K21) MMC2_CLK */
+			AM62PX_IOPAD(0x011C, PIN_INPUT_PULLUP, 0) /* () MMC2_CLKLB */
+			AM62PX_IOPAD(0x0114, PIN_INPUT_PULLUP, 0) /* (K23) MMC2_DAT0 */
+			AM62PX_IOPAD(0x0110, PIN_INPUT_PULLUP, 0) /* (K22) MMC2_DAT1 */
+			AM62PX_IOPAD(0x010c, PIN_INPUT_PULLUP, 0) /* (L20) MMC2_DAT2 */
+			AM62PX_IOPAD(0x0108, PIN_INPUT_PULLUP, 0) /* (L21) MMC2_DAT3 */
+		>;
+	};
+
+	pinctrl_rgmii1: main-rgmii1-default-pins {
+		pinctrl-single,pins = <
+			AM62PX_IOPAD(0x014c, PIN_INPUT, 0) /* (B15) RGMII1_RD0 */
+			AM62PX_IOPAD(0x0150, PIN_INPUT, 0) /* (B16) RGMII1_RD1 */
+			AM62PX_IOPAD(0x0154, PIN_INPUT, 0) /* (A14) RGMII1_RD2 */
+			AM62PX_IOPAD(0x0158, PIN_INPUT, 0) /* (B14) RGMII1_RD3 */
+			AM62PX_IOPAD(0x0148, PIN_INPUT, 0) /* (A16) RGMII1_RXC */
+			AM62PX_IOPAD(0x0144, PIN_INPUT, 0) /* (A15) RGMII1_RX_CTL */
+			AM62PX_IOPAD(0x0134, PIN_INPUT, 0) /* (A18) RGMII1_TD0 */
+			AM62PX_IOPAD(0x0138, PIN_INPUT, 0) /* (C17) RGMII1_TD1 */
+			AM62PX_IOPAD(0x013c, PIN_INPUT, 0) /* (A17) RGMII1_TD2 */
+			AM62PX_IOPAD(0x0140, PIN_INPUT, 0) /* (C16) RGMII1_TD3 */
+			AM62PX_IOPAD(0x0130, PIN_INPUT, 0) /* (B17) RGMII1_TXC */
+			AM62PX_IOPAD(0x012c, PIN_INPUT, 0) /* (B18) RGMII1_TX_CTL */
+		>;
+		bootph-all;
+	};
+
+	pinctrl_spi0: main-spi0-default-pins {
+		pinctrl-single,pins = <
+			AM62PX_IOPAD(0x01bc, PIN_OUTPUT, 0) /* (B21) SPI0_CLK */
+			AM62PX_IOPAD(0x01b4, PIN_OUTPUT, 0) /* (D20) SPI0_CS0 */
+			AM62PX_IOPAD(0x01c0, PIN_OUTPUT, 0) /* (B20) SPI0_D0 */
+			AM62PX_IOPAD(0x01c4, PIN_INPUT, 0) /* (C21) SPI0_D1 */
+		>;
+	};
+
+	pinctrl_uart5: main-uart5-default-pins {
+		pinctrl-single,pins = <
+			AM62PX_IOPAD(0x00ec, PIN_INPUT, 4) /* (AC21) VOUT0_DATA13.UART5_CTSn */
+			AM62PX_IOPAD(0x00e8, PIN_OUTPUT, 4) /* (AD21) VOUT0_DATA12.UART5_RTSn */
+			AM62PX_IOPAD(0x00d0, PIN_INPUT, 4) /* (AC23) VOUT0_DATA6.UART5_RXD */
+			AM62PX_IOPAD(0x00d4, PIN_OUTPUT, 4) /* (AE23) VOUT0_DATA7.UART5_TXD */
+		>;
+	};
+
+	pinctrl_bt: main-btgrp-pins {
+		pinctrl-single,pins = <
+			AM62PX_IOPAD(0x00f4, PIN_OUTPUT, 7) /* (Y20) VOUT0_DATA15.GPIO0_60 (BT_EN) */
+		>;
+	};
+
+	pinctrl_restouch: main-restouch-pins {
+		pinctrl-single,pins = <
+			AM62PX_IOPAD(0x00c4, PIN_INPUT_PULLUP, 7) /* (Y23) VOUT0_DATA3.GPIO0_48 */
+		>;
+	};
+
+	pinctrl_wifi: main-wifi-default-pins {
+		pinctrl-single,pins = <
+			AM62PX_IOPAD(0x00dc, PIN_OUTPUT, 7) /* (AC22) VOUT0_DATA9.GPIO0_54 - WIFI_PWR_EN - */
+			AM62PX_IOPAD(0x00f0, PIN_OUTPUT, 7) /* (AA20) VOUT0_DATA14.GPIO0_59 - WIFI_EN - */
+		>;
+	};
+};
+
+&mcu_pmx0 {
+	pinctrl_wkup_clkout0: wkup-clkout0-default-pins {
+		pinctrl-single,pins = <
+			AM62PX_MCU_IOPAD(0x0084, PIN_OUTPUT, 0) /* (F13) WKUP_CLKOUT0 */
+		>;
+	};
+};
+
+&main_spi0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi0>;
+	ti,pindir-d0-out-d1-in;
+
+	/* Resistive touch controller */
+	ads7846@0 {
+		compatible = "ti,ads7846";
+		reg = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_restouch>;
+		interrupt-parent = <&main_gpio0>;
+		interrupts = <48 IRQ_TYPE_EDGE_FALLING>;
+		spi-max-frequency = <1500000>;
+		pendown-gpio = <&main_gpio0 48 GPIO_ACTIVE_LOW>;
+		ti,x-min = /bits/ 16 <125>;
+		ti,x-max = /bits/ 16 <4008>;
+		ti,y-min = /bits/ 16 <282>;
+		ti,y-max = /bits/ 16 <3864>;
+		ti,x-plate-ohms = /bits/ 16 <180>;
+		ti,pressure-max = /bits/ 16 <255>;
+		ti,debounce-max = /bits/ 16 <10>;
+		ti,debounce-tol = /bits/ 16 <3>;
+		ti,debounce-rep = /bits/ 16 <1>;
+		ti,settle-delay-usec = /bits/ 16 <150>;
+		ti,keep-vref-on;
+		wakeup-source;
+		status = "okay";
+	};
+};
+
+&main_uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>, <&pinctrl_bt>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "nxp,88w8987-bt";
+	};
+};
+
+&mcasp1 {
+	status = "okay";
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_mcasp1>;
+	op-mode = <0>;          /* MCASP_IIS_MODE */
+	tdm-slots = <2>;
+	serial-dir = <  /* 0: INACTIVE, 1: TX, 2: RX */
+	       1 0 2 0
+	       0 0 0 0
+	       0 0 0 0
+	       0 0 0 0
+	>;
+	tx-num-evt = <0>;
+	rx-num-evt = <0>;
+};
+
+/* eMMC */
+&sdhci0 {
+	status = "okay";
+	ti,driver-strength-ohm = <50>;
+	mmc-pwrseq = <&mmc_pwrseq>;
+	disable-wp;
+	bootph-all;
+};
+
+/* WIFI */
+&sdhci2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_mmc2>, <&pinctrl_wifi>;
+	bus-width = <4>;
+	disable-wp;
+	non-removable;
+	keep-power-in-suspend;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	ti,fails-without-test-cd;
+	status = "okay";
+};
+
+&usbss0 {
+	ti,vbus-divider;
+};
+
+&usbss1 {
+	ti,vbus-divider;
+};
-- 
2.43.0