From: Luca Ceresoli <luca.ceresoli@bootlin.com>
To: Andrzej Hajda <andrzej.hajda@intel.com>,
Neil Armstrong <neil.armstrong@linaro.org>,
Robert Foss <rfoss@kernel.org>,
Laurent Pinchart <Laurent.pinchart@ideasonboard.com>,
Jonas Karlman <jonas@kwiboo.se>,
Jernej Skrabec <jernej.skrabec@gmail.com>,
Maarten Lankhorst <maarten.lankhorst@linux.intel.com>,
Maxime Ripard <mripard@kernel.org>,
Thomas Zimmermann <tzimmermann@suse.de>,
David Airlie <airlied@gmail.com>,
Simona Vetter <simona@ffwll.ch>
Cc: Hui Pu <Hui.Pu@gehealthcare.com>,
Thomas Petazzoni <thomas.petazzoni@bootlin.com>,
dri-devel@lists.freedesktop.org, linux-kernel@vger.kernel.org,
Luca Ceresoli <luca.ceresoli@bootlin.com>,
Dmitry Baryshkov <lumag@kernel.org>
Subject: [PATCH 2/2] drm/bridge: ti-sn65dsi83: protect device resources on unplug
Date: Fri, 08 Aug 2025 15:24:29 +0200 [thread overview]
Message-ID: <20250808-drm-bridge-atomic-vs-remove-v1-2-a52e933b08a8@bootlin.com> (raw)
In-Reply-To: <20250808-drm-bridge-atomic-vs-remove-v1-0-a52e933b08a8@bootlin.com>
To support hot-unplug of this bridge we need to protect access to device
resources in case sn65dsi83_remove() happens concurrently to other code.
Some care is needed for the case when the unplug happens before
sn65dsi83_atomic_disable() has a chance to enter the critical section
(i.e. a successful drm_bridge_enter() call), which occurs whenever the
hardware is removed while the display is active. When that happens,
sn65dsi83_atomic_disable() in unable to release some resources, thus this
needs to be done in sn65dsi83_remove() after drm_bridge_unplug().
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
---
drivers/gpu/drm/bridge/ti-sn65dsi83.c | 53 +++++++++++++++++++++++++++++++++++
1 file changed, 53 insertions(+)
diff --git a/drivers/gpu/drm/bridge/ti-sn65dsi83.c b/drivers/gpu/drm/bridge/ti-sn65dsi83.c
index 033c44326552ab167d4e8d9b74957c585e4c6fb7..9e4cecf4f7cb056f0c34e87007fcebf50780e49c 100644
--- a/drivers/gpu/drm/bridge/ti-sn65dsi83.c
+++ b/drivers/gpu/drm/bridge/ti-sn65dsi83.c
@@ -157,6 +157,7 @@ struct sn65dsi83 {
struct drm_bridge *panel_bridge;
struct gpio_desc *enable_gpio;
struct regulator *vcc;
+ bool disable_resources_needed;
bool lvds_dual_link;
bool lvds_dual_link_even_odd_swap;
int lvds_vod_swing_conf[2];
@@ -406,6 +407,10 @@ static void sn65dsi83_reset_work(struct work_struct *ws)
{
struct sn65dsi83 *ctx = container_of(ws, struct sn65dsi83, reset_work);
int ret;
+ int idx;
+
+ if (!drm_bridge_enter(&ctx->bridge, &idx))
+ return;
/* Reset the pipe */
ret = sn65dsi83_reset_pipe(ctx);
@@ -415,12 +420,18 @@ static void sn65dsi83_reset_work(struct work_struct *ws)
}
if (ctx->irq)
enable_irq(ctx->irq);
+
+ drm_bridge_exit(idx);
}
static void sn65dsi83_handle_errors(struct sn65dsi83 *ctx)
{
unsigned int irq_stat;
int ret;
+ int idx;
+
+ if (!drm_bridge_enter(&ctx->bridge, &idx))
+ return;
/*
* Schedule a reset in case of:
@@ -441,6 +452,8 @@ static void sn65dsi83_handle_errors(struct sn65dsi83 *ctx)
schedule_work(&ctx->reset_work);
}
+
+ drm_bridge_exit(idx);
}
static void sn65dsi83_monitor_work(struct work_struct *work)
@@ -478,10 +491,15 @@ static void sn65dsi83_atomic_pre_enable(struct drm_bridge *bridge,
__le16 le16val;
u16 val;
int ret;
+ int idx;
+
+ if (!drm_bridge_enter(bridge, &idx))
+ return;
ret = regulator_enable(ctx->vcc);
if (ret) {
dev_err(ctx->dev, "Failed to enable vcc: %d\n", ret);
+ drm_bridge_exit(idx);
return;
}
@@ -625,6 +643,8 @@ static void sn65dsi83_atomic_pre_enable(struct drm_bridge *bridge,
dev_err(ctx->dev, "failed to lock PLL, ret=%i\n", ret);
/* On failure, disable PLL again and exit. */
regmap_write(ctx->regmap, REG_RC_PLL_EN, 0x00);
+ ctx->disable_resources_needed = true;
+ drm_bridge_exit(idx);
return;
}
@@ -633,6 +653,9 @@ static void sn65dsi83_atomic_pre_enable(struct drm_bridge *bridge,
/* Wait for 10ms after soft reset as specified in datasheet */
usleep_range(10000, 12000);
+
+ ctx->disable_resources_needed = true;
+ drm_bridge_exit(idx);
}
static void sn65dsi83_atomic_enable(struct drm_bridge *bridge,
@@ -640,6 +663,10 @@ static void sn65dsi83_atomic_enable(struct drm_bridge *bridge,
{
struct sn65dsi83 *ctx = bridge_to_sn65dsi83(bridge);
unsigned int pval;
+ int idx;
+
+ if (!drm_bridge_enter(bridge, &idx))
+ return;
/* Clear all errors that got asserted during initialization. */
regmap_read(ctx->regmap, REG_IRQ_STAT, &pval);
@@ -659,6 +686,8 @@ static void sn65dsi83_atomic_enable(struct drm_bridge *bridge,
/* Use the polling task */
sn65dsi83_monitor_start(ctx);
}
+
+ drm_bridge_exit(idx);
}
static void sn65dsi83_atomic_disable(struct drm_bridge *bridge,
@@ -666,6 +695,10 @@ static void sn65dsi83_atomic_disable(struct drm_bridge *bridge,
{
struct sn65dsi83 *ctx = bridge_to_sn65dsi83(bridge);
int ret;
+ int idx;
+
+ if (!drm_bridge_enter(bridge, &idx))
+ return;
if (ctx->irq) {
/* Disable irq */
@@ -685,6 +718,9 @@ static void sn65dsi83_atomic_disable(struct drm_bridge *bridge,
dev_err(ctx->dev, "Failed to disable vcc: %d\n", ret);
regcache_mark_dirty(ctx->regmap);
+
+ ctx->disable_resources_needed = false;
+ drm_bridge_exit(idx);
}
static enum drm_mode_status
@@ -1005,7 +1041,24 @@ static void sn65dsi83_remove(struct i2c_client *client)
{
struct sn65dsi83 *ctx = i2c_get_clientdata(client);
+ drm_bridge_unplug(&ctx->bridge);
drm_bridge_remove(&ctx->bridge);
+
+ /*
+ * sn65dsi83_atomic_disable() should release some resources, but it
+ * cannot if we call drm_bridge_unplug() before it can
+ * drm_bridge_enter(). If that happens, let's release those
+ * resources now.
+ */
+ if (ctx->disable_resources_needed) {
+ if (!ctx->irq)
+ sn65dsi83_monitor_stop(ctx);
+
+ gpiod_set_value_cansleep(ctx->enable_gpio, 0);
+ usleep_range(10000, 11000);
+
+ regulator_disable(ctx->vcc);
+ }
}
static const struct i2c_device_id sn65dsi83_id[] = {
--
2.50.1
next prev parent reply other threads:[~2025-08-08 13:53 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-08-08 13:24 [PATCH 0/2] drm/bridge: handle gracefully atomic updates during bridge removal Luca Ceresoli
2025-08-08 13:24 ` [PATCH 1/2] drm/bridge: add drm_bridge_unplug() and drm_bridge_enter/exit() Luca Ceresoli
2025-08-08 13:24 ` Luca Ceresoli [this message]
2025-08-19 12:29 ` [PATCH 2/2] drm/bridge: ti-sn65dsi83: protect device resources on unplug Maxime Ripard
2025-08-20 11:13 ` Luca Ceresoli
2025-08-27 7:46 ` Maxime Ripard
2025-09-08 13:49 ` Luca Ceresoli
2025-09-10 10:59 ` Maxime Ripard
2025-09-10 16:47 ` Luca Ceresoli
2025-09-15 12:03 ` Maxime Ripard
2025-09-15 14:51 ` Luca Ceresoli
2025-09-26 16:37 ` Luca Ceresoli
2025-10-07 15:09 ` Maxime Ripard
2025-10-09 14:48 ` Luca Ceresoli
2025-09-08 13:49 ` Luca Ceresoli
2025-09-10 7:52 ` Maxime Ripard
2025-09-10 16:34 ` Luca Ceresoli
2025-09-11 6:44 ` Maxime Ripard
2025-09-11 13:09 ` Luca Ceresoli
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20250808-drm-bridge-atomic-vs-remove-v1-2-a52e933b08a8@bootlin.com \
--to=luca.ceresoli@bootlin.com \
--cc=Hui.Pu@gehealthcare.com \
--cc=Laurent.pinchart@ideasonboard.com \
--cc=airlied@gmail.com \
--cc=andrzej.hajda@intel.com \
--cc=dri-devel@lists.freedesktop.org \
--cc=jernej.skrabec@gmail.com \
--cc=jonas@kwiboo.se \
--cc=linux-kernel@vger.kernel.org \
--cc=lumag@kernel.org \
--cc=maarten.lankhorst@linux.intel.com \
--cc=mripard@kernel.org \
--cc=neil.armstrong@linaro.org \
--cc=rfoss@kernel.org \
--cc=simona@ffwll.ch \
--cc=thomas.petazzoni@bootlin.com \
--cc=tzimmermann@suse.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®